Question about 1993 Dodge Dakota

1 Answer

How to remove wiper arms from truck - 1993 Dodge Dakota

Posted by on

Ad

1 Answer

Lift the wiper blade off the windshield
On the right side of the arm, where it goes over the serrated drive wheel,there is a little metal slide.
Move it out to the right, and take off wiper arm

Now to do it real easy,you buy a tool from Snap-On, you will love
It hooks over the end of the arm,you wrap you fingers around the arm, to remove spring tension.
Really nice tool and easy to use

Posted on Nov 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions to replqce driver side wiper motor 2005 cavalier


Wiper motor or wiper blade or arm ? There is one wiper motor for both windshield wipers . You would need to take both wiper arms off an remove the plastic cowling under wiper arms . The motor is under there . Plastic push pins hold the cowling . Open the hood after removing the wiper arms . Plastic caps on the wiper arms come off , 1/2 or 13mm nut has to be removed . Then rock the arms back an fourth till they come off . There may be a video on youtube showing how . Check it out .

Feb 22, 2017 | Cars & Trucks

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

I'm looking for instructions on how to replace the window wiper motor and switch


Windshield Wiper Motor Removal & Installation To Remove:
Using the J 39232, remove the wiper transmission from the wiper motor crank arm. gmpc_wa_1.gif

  1. Remove the wiper arms
  2. Remove the air inlet grille panel.
  3. Disconnect the connectors from the wiper motor assembly.
  4. Remove the three screws and the wiper drive system module.
  5. Using GM special tool J 39232 or equivalent, separate the wiper motor crank arm from the wiper drive ball joint.
  6. Remove the wiper motor crank arm from the wiper motor.
    • Remove the rubber boot.
    • Loosen the mounting screw.
    • Tap on the screw with a plastic or leather faced hammer while supporting the wiper motor crank arm.
    • Tap the screw until the crank arm is loose.
    • Remove the screw and crank arm from the motor.
  7. Remove the three screws and separate the wiper motor from the module assembly.
To Install:
  1. Position the wiper motor on the wiper drive system module assembly. Install the three mounting screws. Tighten the screws to 62 in lb (7 Nm).
  2. Install the wiper motor crank arm on the wiper motor.
    • Connect the wiper motor electrical connector.
    • Turn the wiper switch to the accessory position.
    • Turn the wiper switch to the pulse position.
    • Turn the wiper switch off when the wiper motor is in the middle of the wipe cycle.
    • Disconnect the connector from the motor.
    • Maintain a gap of 0.157-0.314 in (4-8 mm) between the wiper motor crank arm and the bracket tab. If the gap is not 0.157-0.314 in (4-8 mm), remove the wiper motor crank arm and repeat installation.
    • Install the mounting screw. Tighten to 142 in lb (16 Nm).
    • Install the rubber boot.
  3. Position the wiper drive system module on the vehicle. Install the three mounting screws. Tighten the screws to 68 in lb (10 Nm).
  4. Using GM special tool J 39232 or equivalent, connect the wiper motor crank arm to the wiper drive ball joint.
  5. Connect the wiper motor assembly electrical connector.
  6. Install the air inlet grille panel.
  7. Install the wiper arms.
  8. Check the windshield wiper operation.
---

Oct 28, 2010 | 1999 Buick Regal

1 Answer

I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
  1. Turn ignition switch to ACCY position.
  2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
  3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
To Install:
  1. Insert wiper arm hook through opening in wiper blade.
  2. Place wiper blade pivot in the inside radius of wiper arm hook.
  3. Pull on wiper blade pivot into hook until it locks into place.
  4. Check wipers for proper operation.
Wiper Arm To Remove:
NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
  1. Remove washer hose.
  2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
  3. Remove wiper arm from shaft.
To Install:
  1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
  2. Press arm assembly on shaft and push retaining latch IN.
  3. Connect washer hose.
  4. Remove windshield markings and check wipers for proper operation.
prev.gif next.gif

Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Wipers will not move, makes noise and there is power to the motor. Motor was replaced. Someone told me that the arms probably moved to far and are now stuck, how do I fix this?


Windshield Wiper Blade & Arm Removal & Installation Front To Remove:
  1. Mark the location of the wiper on the windshield.
  2. Remove or disconnect the following:
    • Nut cover
    • Nut from the wiper arm
    • Wiper arm
Wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt.gif
To Install:
  1. Install or connect the following:
    • Secure the wiper arm with the nut.
      1. Tighten to: 17 ft-lb (23 Nm)
    • Nut cover
Rear To Remove:
  1. Put the wiper arm in the park position.
  2. Remove or disconnect the following:
    • The washer hose from the connector
    • The cap from the wiper arm
    • The nut from the wiper arm
    • The wiper arm from the wiper motor shaft
Rear wiper arm mounting nut gm_truck_s10_w-wpr-arm_ret-nt_rr.gif
To Install:
  1. Install or connect the following:
    • The wiper arm on the wiper motor shaft in the park position with the wiper arm resting on the park ramp
    • The nut on the wiper arm
      1. Tighten the nut. Torque to: 17 ft lbs (23 nm)
    • The cap on the wiper arm
    • The washer hose on the connector

---
The wiper motor hopefully is ok, but if the wiper arms were not mounted at the right spot, it could have damaged the motor as it returned to the rest position, unfortunately.

If there is noise, the noise could be coming from the wiper arm joint being stripped out or the motor itself assuming that the ball joints under the hood and behind the firewall are still connected.

Check these items, and I'm sure you will get to the bottom of this.

Good luck on this repair.

Oct 08, 2010 | 1997 Chevrolet Blazer

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

Removing windshield wiper assembly ford excursion


Wiper Pivot Arm Removal and Installation
  1. Lift the windshield wiper pivot arm to the full upright position.
  1. Remove the windshield wiper pivot arm.
    1. Release the locking tab.
    1. Remove the windshield wiper pivot arm.
52fed05.gif
  1. NOTE: During installation, it is necessary to pull the locking tab out to its full open (unlatched) position and hold while assembling the pivot arm onto the mounting arm and pivot shaft. Align the key on the pivot arm head with the keyway on the shafts. This will make sure the pivot arm is correctly aligned. If necessary, the key can be removed. To adjust wiper pivot arms, refer to Wiper Blade and Pivot Arm Adjustment in this section.
    To install, reverse the removal procedure.

Jul 02, 2009 | 2005 Ford Excursion

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

2 Answers

Cant take off the windsheild wipers


Here is the procedure to remove the wiper motor. It says to remove wipers by removing the nut covers then remove the wiper nuts. Is this what your talking about?
If your talking about the wiper arms they just pop off at the swivel.
Use this link for info on removing blade assy.
http://www.autozone.com/az/cds/en_us/0900823d/80/04/f8/26/0900823d8004f826/repairInfoPages.htm

Wiper Motor
Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Park the wiper pivot arms in the highest position on the glass.
  3. Disconnect the battery ground cable.
  4. Remove the wiper pivot arm nut covers.
  5. Remove the nuts and the wiper pivot arms.
  6. Remove the cowl top vent panels.
  7. Remove the four bolts, wiper mounting arm and wiper pivot shaft assembly.
  8. Disconnect the electrical connector.
  9. Remove the bolt and the windshield wiper motor operating arm from the motor.
  10. Remove the three bolts and remove the windshield wiper motor.
  11. To install, reverse the removal procedure.

Jan 28, 2009 | 2005 Ford Taurus

Not finding what you are looking for?

Open Questions:

See all 1993 Dodge Dakota Questions

1993 Dodge Dakota Logo

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...