Question about Mitsubishi Lancer

1 Answer

Well I give up looking for a wiring diagram. The fast idel and choke system doesnt't work. The solenoid in the vacuum system is not beeing excited when the engine is cold. Where can I fid a wiring diagram on the internet? Thanks Ken

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Year? engine? the 2.6L engine and carb is really bad. the vacuum choke pull off would go bad, then the cat converter would plug up because the engine ran so rich. Chrysler used that same engine in their minivans and Mazda also used it a few years.

Posted on Nov 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a vacuum hose routing diagram for a 99 VW Beetle 2.0


VACUUM LINE DIAGRAMS


There are few direct links showing exact vacuum line diagrams. I suggest you to refer the direct links.


Click the link below: -----

---------------

How to locate the vacuum leak?

http://howtobyme.blogspot.in/2012/01/how-to-locate-vacuum-leak.html

-----------------

Vacuum Hose Routing Diagram For 1995 Chevrolet Corvette Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html

------------

VACUUM DIAGRAMS For Audi A4?

http://repairhelpcenter.blogspot.com/2011/11/vacuum-diagrams-for-audi-a4.html

--------------------

VACUUM DIAGRAMS For VW Passat?

http://vwrepairhelp.blogspot.com/2011/11/vacuum-diagrams-for-vw-passt.html

-------------

Vacuum line diagram For 1996 Chevrolet Lumina?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-line-diagram-for-1996-chevrolet.html

--------------

Vacuum Hose Routing Diagram For 1995 Chevrolet Corvette Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html

-------------

Vacuum diagram for Isuzu?

http://technoanswers.blogspot.com/2012/01/vacuum-diagram-for-isuzu.html

-------------

Ford 4 wheel drive vacuum solenoid working system?

http://technoanswers.blogspot.in/2012/02/ford-4-wheel-drive-vacuum-solenoid.html

------------

These will help.

Thanks.

Dec 06, 2012 | 1998 Volkswagen Beetle

2 Answers

No vacume to the erg


Vacuum line clogged or Vacuum controlling solenoid/motor issue.

There re few direct links showing exact vacuum line diagrams. I suggest you to refer the direct links.


Click the link below: -----

---------------

How to locate the vacuum leak?

http://howtobyme.blogspot.in/2012/01/how-to-locate-vacuum-leak.html

-----------------

Vacuum Hose Routing Diagram For 1995 Chevrolet Corvette Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html

------------

VACUUM DIAGRAMS For Audi A4?

http://repairhelpcenter.blogspot.com/2011/11/vacuum-diagrams-for-audi-a4.html

--------------------

VACUUM DIAGRAMS For VW Passat?

http://vwrepairhelp.blogspot.com/2011/11/vacuum-diagrams-for-vw-passt.html

-------------

Vacuum line diagram For 1996 Chevrolet Lumina?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-line-diagram-for-1996-chevrolet.html

--------------

Vacuum Hose Routing Diagram For 1995 Chevrolet Corvette Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html

-------------

Vacuum diagram for Isuzu?

http://technoanswers.blogspot.com/2012/01/vacuum-diagram-for-isuzu.html

-------------

Ford 4 wheel drive vacuum solenoid working system?

http://technoanswers.blogspot.in/2012/02/ford-4-wheel-drive-vacuum-solenoid.html

------------

These will help.

Thanks.

Nov 27, 2012 | 2003 Cadillac Deville

1 Answer

R & R motor and where do the vacum lines


There re few direct links showing exact vacuum line diagrams.I suggest you to refer the direct links.

Click the link below:-----
---------------
How to locate the vacuum leak? http://howtobyme.blogspot.in/2012/01/how-to-locate-vacuum-leak.html

-----------------
Vacuum Hose Routing Diagram For 1995 Chevrolet Corvette Throttle Body?

http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html

------------


VACUUM DIAGRAMS For Audi A4?

http://repairhelpcenter.blogspot.com/2011/11/vacuum-diagrams-for-audi-a4.html

--------------------
VACUUM DIAGRAMS For VW Passat? http://vwrepairhelp.blogspot.com/2011/11/vacuum-diagrams-for-vw-passt.html
------------- Vacuum line diagram For 1996 Chevrolet Lumina? http://schematicsdiagram.blogspot.com/2011/12/vacuum-line-diagram-for-1996-chevrolet.html
-------------- Vacuum Hose Routing Diagram For 1995 Chevrolet Corvette Throttle Body? http://schematicsdiagram.blogspot.com/2011/12/vacuum-hose-routing-diagram-for-1995.html
------------- Vacuum diagram for Isuzu? http://technoanswers.blogspot.com/2012/01/vacuum-diagram-for-isuzu.html


-------------
Ford 4 wheel drive vacuum solenoid working system? http://technoanswers.blogspot.in/2012/02/ford-4-wheel-drive-vacuum-solenoid.html

------------
These will help.
Thanks.

Nov 26, 2012 | Cars & Trucks

1 Answer

I have a 2kd-ftv motor in a toyota hiace van, it starts and runs for 3-4 seconds getting lower and lower in revs till it stalls , sometimes it doesnt stall and picks up after same amount of time and idels...


Hi, you need to firstly replace the fuel filter, the problem is the idle solenoid in the pump has dirt in the piston! From the passenger side of the engine remove the solenoid at the back of the fuel pump 2x 5mm Alan bolts, there is 2 solenoids in the pump the one closest to the block is fuel temp. After the idle solenoid is removed, in the solenoid is a piston held in place by a circlip and there is also a spring in there, clean out all dirt inside and reassemble replace both o'rings and reinstall your problem will be solved. I have just fixed one 2 days ago.

Oct 31, 2010 | 2005 Toyota Tacoma

1 Answer

Fast idle


The specification calls for 900 rpms for the idle speed when warm for the 1987 Dodge Shadow.

One can adjust this with a screw on the carburetor, if it has one.

If it's fuel injected the idle speed is automatically controlled.

Fast Idle Speed HOLLEY 5220/6520 Fig. 5: Turn the adjusting screw with a screwdriver to raise or lower the fast idle speed — make sure that the adjusting screw is resting against the lowest speed step 86735g04.gif
NOTE: This procedure is performed while the carburetor is installed on the engine.
  1. On 1981–82 cars, disengage the two-way electrical connector at the carburetor (red and tan wires).
  2. On all years, disconnect the jumper wire at the radiator fan and install a jumper wire so that the fan runs continuously.
  3. On 1983–86 models, pull the PCV valve out of the valve cover and allow it to draw underhood air.
  4. Disengage the oxygen sensor system connector located on the left fender shield near the shock tower.
  5. Ground the carburetor switch with a jumper wire.
  6. Open the throttle slightly and place the adjustment screw on the slowest speed step of the fast idle cam.
  7. With the choke fully open, adjust the fast idle speed to comply with the value indicated on the underhood sticker.
  8. Return the vehicle to curb idle, then reposition the adjusting screw on the slowest speed step of the fast idle cam to verify fast idle speed. Re-adjust as necessary.
  9. Turn the engine OFF, remove the jumper wire and reconnect the fan.
  10. Reinstall the PCV valve and remove the tachometer. On 1983–86 models, reattach the oxygen sensor system connector, and remove the jumper wire from the carburetor.
Fast Idle Opening MIKUNI
  1. Before adjustment, leave the carburetor alone for approximately one hour at 73°F (23°C).
  2. Adjust the fast idle opening by turning the fast idle adjusting screw to the following specified values (drill diameter):
    • 2.6L engines equipped with manual transaxles — 0.028 in.
    • 2.6L engines equipped with automatic transaxles — 0.031 in.
Choke Valve Setting MIKUNI Fig. 6: After tightening the choke cover lockscrews, cut the heads off of lockscrews A (total of 3 screws) and stake the heads of lockscrews B (total of 2 screws) with a blunt punch 86735g56.gif
NOTE: This procedure need only be performed if the carburetor is disassembled.
  1. Fit the strangler spring to the choke lever.
  2. Assemble the choke valve, aligning the inscribed line or black painted line on the tooth of the choke pinion with the inscribed line on the cam lever.
  3. Temporarily tighten the new lockscrews.
  4. Set the choke valve by moving the pinion arm up or down, align a punched mark on the float chamber cover at the center of the three inscribed lines, and secure the pinion arm with the lockscrews.
  5. Install the choke cover and tighten the lockscrews.
  6. Cut off the heads off of lockscrews A.
  7. Stake the heads of lockscrews B using a blunt punch.
Vacuum Kick HOLLEY 5220/6520 NOTE: This procedure is performed while the carburetor is installed on the engine. If the vacuum kick is adjusted to open the choke too far, the engine may stall or idle very roughly just after cold start. If it is adjusted so that the choke does not open enough, there may be black smoke in the exhaust. NOTE: To perform this procedure, you will need a hand held vacuum pump capable of producing at least 15 in. Hg (50.6 kPa) of vacuum. The vacuum kick diaphragm may be damaged if you attempt to retract it manually. You will also need a drill or dowel which has a diameter equivalent to the specification for Vacuum Kick in the Carburetor Specifications Chart.
  1. Remove the air cleaner. Open the throttle, close the choke and hold it in the closed position, and then release the throttle to trap the fast idle cam in the choke-closed position.
  2. Disconnect the vacuum hose at the choke vacuum kick diaphragm. Connect a vacuum pump and apply 15 in. Hg (50.6 kPa) or more of vacuum.
  3. Gently move the choke blade toward the closed position just until play is eliminated from the vacuum kick linkage (so that the vacuum kick is determining choke blade position).
  4. Insert the drill or dowel into the gap between the upper edge of the choke blade and the air horn wall, toward the center of the gap. The dowel or drill should just fit into the gap. If necessary, rotate the Allen head screw in the center of the diaphragm housing to create the proper gap and then recheck with the measuring device.
  5. Restore all vacuum connections and reinstall the air cleaner.

Aug 05, 2010 | 1987 Dodge Shadow

2 Answers

Vacume hubs i am looking for the air leak need vacume diagram for a 05 f150 supercrew


IF this is a case that the IWEs will not disengage, it could be the IWE solenoid or the vacuum lines to the IWEs. Could also be a problem with the vent lines from the IWE ( the other vacuum line that runs up into the engine compartment, and just hangs there ).

This is the block diagram of the vacuum lines for the IWE ( not actual routing ). You can use a vacuum pump / gauge to see if the lines will hold vacuum. Don't be surprised if the vacuum lines test OK, there is a TSB on the IWE solenoid where it could ingest water, and allow water in the lines, which will not keep the IWE gears disengaged.

Block diagram of the IWE system
b893440.jpg

TSB on the IWE solenoid ( right click save as )
http://my.voyager.net/~sscully/file_tsb06_08_15.pdf


May 30, 2010 | 2005 Ford F-150

3 Answers

4x4 lights on dash come on,transferr case kicks


Sounds like the selinoid on the transfer case is not fully ingaged.....?

Dec 20, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

1985 S10 Blazer; Choke light comes on, overcharge indicated


As for your choke problem--- Check for blown fuse under dash labeled as choke. If ok then check for faulty fuseable link at starter.

Mar 31, 2009 | 1985 Chevrolet S-10 Blazer

1 Answer

Idleling of 1984 F250 Ford PU


mcdevito75, That carb, solonoid most likely works with both, electricity and vacum, That blue wire should hook up to that solonoid, look at the plug ans solonoid and see if there"s a point for the wire. If it has broken off yo"ll have to replace the solonoid. Also have the choke system on your truck checked out, if the choke is not operateing as it should this too can cause your problem. Have your local repair shop take a look.

Dec 04, 2008 | 1984 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...