Question about 1995 Jeep Wrangler

1 Answer

My 1993 jeep wrangler clutch keeps giving out even after i bleed the line..any thoughts? it works fine for a little while then goes to the floor again

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,672 Answers

Replace the CLUTCH MASTER and SLAVE assembly! Age of that classic jeep needs NEW CLUTCH MASTER and SLAVE! That part together w/ clutch slave should be change! Personally i have experience replacing the kit only, it didn't last longer than expected and even got me in trouble, and I spend like i bought a NEW one! So its up to you to decide? taaah!

Posted on Nov 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Having trouble bleeding brakes for 2009 jeep wrangle 4wh drive when car is off the brakes seem fine , but when the car is on the brake pedal goes almost to the floor


Because when you start it the brake booster will start working, start bleed on wheel farthest from master cylinder and work closer, one at a time pump up and bleed each line at least once after you don't see air anymore...

Jul 22, 2014 | 2009 Jeep Wrangler

1 Answer

After changing transmission and clutch in 91 Wrangler, clutch goes to floor. Tried bleeding line but didn't work.


The clutch should go to the floor =) But if it's not disengaging the clutch disk, there's definitely a problem between the pedal and the clutch disk. I'm guessing you have a hydraulic clutch?

Apr 19, 2012 | 1991 Jeep Wrangler

1 Answer

I have no clutch pressure half way, then very little from there to the floor. why?


check fluid in little cylinder beside brake master cyl.if very low or empty will need to bleed cylinder on side of transmission.

Feb 13, 2011 | 1993 Jeep Wrangler

1 Answer

How do you do you bleed a clutch line on a 1993 jeep wrangler?


Just like you would bleed brakes. Fill the reservior with brake fluid, open the bleeder screw and have a friend press the clutch pedal in. Close the bleeder screw and let up on the clutch. Do that until the clutch pedal has a good feel. Be sure to check the reservoir frequently as they don't hold much fluid and if you let it get low you'll **** more air into the system.

Jul 31, 2010 | 1993 Jeep Wrangler

2 Answers

98 wrangler - brake pedal goes all the way to the floor. The master cylinder and all brake lines are free of leaks. I'm not losing any brake fluid anywhere. I replaced the booster that is attached to the...


You changed the master cylinder and vacuum booster and have no leaks anywhere, but did you bleed the entire brake system after you did this work? A little bit of air in any of the lines will make the brakes ineffective.

May 30, 2017 | 1998 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

1 Answer

Problem going into gear


Your clutch system works the same as brakes do. The necessity to bleed tells you that there is a malfunction permitting air into the system. Check where the pedal rod goes into the firewall under the dash, the line itself, and the slave unit (some are inside the bellhousing...look for fluid dripping from bottom to verify if leaking) Not unlike brake master, they can also internally bypass. If you find no leaks, change master. Bleed system and you should be fine

Jul 11, 2009 | 1995 Jeep Wrangler

1 Answer

Brake fluid seems to be full


bleed brake lines they have air in them

Mar 21, 2009 | 1993 Jeep Wrangler

1 Answer

Push down on clutch pedal can't get car into gear


Likely, you have a hydraulic clutch system. Check clutch master cylijnder for fluid and leakage, check hydraulic line and slave cylinder for leaks. If fluid low or empty, bleed as you would a brake wheel cylinder. If full,have someone work the clutch while you watch slave cylinder to make sure it is moving clutch fork. If system full and little or no movement, the master may be "bypassing" internally (replace) Also, check pedal mechanical linkage. Not often but sometimes these parts can break! Could also be athat clutch itself is worn, but this does not happen overnight and you would have noted slip long before this!

Dec 29, 2008 | 1993 Jeep Wrangler

2 Answers

I cant not find the bleed screw or line for a 2000 jeep wrangler 6 cyl,its not where the book says is suppose to be


bleed screw or line for what?? Could you be alittle more specific?? It's hard to help you if you don't give a little more information than bleed screw and line. there are many bleed screws and lines on your Jeep.

Jul 24, 2008 | Jeep Wrangler Cars & Trucks

Not finding what you are looking for?
1995 Jeep Wrangler Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...