Question about 1993 Toyota 4Runner

1 Answer

Changing a rear brake bulb on a hilux surf

How do i get the cover off

Posted by on

1 Answer

You need to undo the 2 bolts on the inside of the body panel, visible when the tailgate is lowered and the gently pull the light unit to the side to remove it from the rear wing. Once this is out replacing the bulb is straight forward. Refitting is a reversal of the above

Posted on Jul 30, 2008

  • Daryl Bird Jun 13, 2013

    Spot on thank you

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why toyota hilux surf gear liver stucking in (p)parking position?please help me i have checked my breake lights but still no lights.


check power to brake light switch. if no power then try to trouble shoot and restore power to brake light pedal switch

Sep 23, 2014 | 1996 Toyota Hilux

1 Answer

Toyota repair manual 1992 hilux surf ssr-x


Hi. it could either be engine lacking power ie fuel or fuel pump,
rings,compression down,brakes binding,timing no vacuum advance working, or clutch slipping.

May 23, 2014 | 1986 Toyota Hilux 2200

1 Answer

How to change high mount brake light bulb in a 2002 lincoln navigator


Instructions
    • 1 Open one of the rear doorsicon1.png of the LS. Position yourself on your knees in the back seat, facing the rear deck or rear dash.
    • 2 Remove the cover from the high-mount brakeicon1.png light assembly, by hand. Pull the cover toward the front of the vehicle. Do not pull extremely hard, or you will break the clips that mount through the deck from the trunk.
    • 3 Pull the old light bulbsicon1.png out of the high-mount assembly. Wrap the new bulbs in a paper tower prior to picking them up. Insert new bulbs into the assembly, by hand. Do not touch the bulb lenses with your hands directly.
    • 4 Install the high-mount cover onto the rear deck and push the cover toward the rear glass to lock it in place.


Read more: http://www.ehow.com/how_10060583_replace-upper-brake-bulb-2001-lincoln-ls.html#ixzz30cNQ559F

May 03, 2014 | Cars & Trucks

1 Answer

How do I access rear signal light to change a bulb on a 2010 jeep, liberty limited?


remove sidings cover then you can see it clearly twist left side to remove bulb then change it

Jan 16, 2014 | 2010 Jeep Liberty

1 Answer

Have toyota hilux surf 1996, what should the rear brake balance be, also for park brake? Would this be the reason right front & left rear holding on?


The front brakes not releasing can only be restricted rubber
brake hoses & rusted caliper pistons,as well as rust on every sliding
surface & no lube, for calipers & pads

The rear is rusted & frozen parking brake cables

Feb 12, 2013 | 1996 Toyota Hilux

1 Answer

Need to change rear brake light bulb on a 2000_L sedan. Owners manual addresses only the turn signal bulb change proceedure. The brake light fixture is flat not round.


there is an access cover in the trunk.Open that and just pull the bulb fixture out replace the bulb and place back in the hole.

Apr 07, 2012 | Saturn Cars & Trucks

1 Answer

How do I replace the brake light in the rear window? How do I get to the bulb?


  • Hi, I can help.

  • To change the third brake on a 1989 Reliant you basically pull out ******* the cover and it pops off the rear window.
  • Now you give the bulb socket a quarter turn to the left.
  • Now pull the old bulb strait out.
  • Now replace the bulb socket.
  • Now firmly replace the cover.

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa

Regards, Tony

Sep 19, 2011 | 1989 Plymouth Reliant

1 Answer

How do i remove right rear lens to change brake light bulb?


Remove the two bolt covers on the rear pillar by prying on the bottom edge with a flat-tip screwdriver.
Remove the bolts with a Phillips head screwdriver, and remove the light assembly from the rear pillar.
Determine which of the two bulbs is burned out: turn signal or brake/taillight.
Remove the socket by turning it one-quarter turn counterclockwise.
Remove the bulb by pulling it straight out of its socket.
Push the new bulb straight into the socket until it bottoms.
Test the lights to make sure the new bulb is working.
Put the socket back into the light assembly, and turn it clockwise to lock it in place.
Install the rear light assembly in the rear pillar. Tighten the two bolts. Snap the bolt covers into position.

Hope this helps you.

Nov 22, 2009 | 2005 Honda Odyssey

2 Answers

Rear drum brakes on hilux wont lock up when heavy brake on gravel


More than likely won't if equiped with Antilock system

Jun 09, 2009 | 1994 Toyota Pickup

1 Answer

Rear brake assembly


hi mate do a google search for 85 hilux rear drum brake diagram and it will give you a few pictures i had the same prob and helped me to fix it

Mar 13, 2009 | 1985 Toyota 4Runner

Not finding what you are looking for?
1993 Toyota 4Runner Logo

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...