Question about 2005 Chevrolet Malibu

1 Answer

Where do i fill my coolant? - 2005 Chevrolet Malibu

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 75 Answers

If you have the v6 3.5 liter engine the coolant jug is located at the back firewall it is a little clear jug with a black lid that is the only way to fill coolant if it is low, due to the fact they dont have a radiator cap like the older cars had, if you are changing your coolant you will also have to bleed the air out of the lines something like brakes if you dont your engine will overheat and blow a headgasket.

Posted on Nov 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coolant fills up engine


coolant filling the engine oil? I would suspect a head gasket or piston liner gasket failure, I this is happening when you fill radiator and engine is still off I would look at the block itself for a crack in the piston wall(internal damage), if this is while running consider the head gaskets

Mar 24, 2014 | 2001 Mitsubishi Montero

1 Answer

Put water in radiator


Usually, all you need to do is fill the radiator, leave the radiator cap off, start car and let it idle until engine reaches normal operating temperature, and the thermostat opens (upper hose will get hot or warm). Then shut off the car, top up radiator and overflow bottle, replace cap, and you are good to go.
I own a Sentra and was recommended when filling the radiator to keep the car running while filling to help expel air. Also many cars have a bleed valve on top of or near the thermostat housing which should be open while filling with coolant, and as soon as coolant starts coming out the bleeder valve, it should be closed, and then continue filling radiator. If you don't have such a bleed valve, and you still think air might be trapped in the engine, you could find a coolant temperature sensor or sender unit that is at or near the top of the coolant passages or areas of the engine where coolant is found, crack it open to make sure only coolant and no air comes out.
The Sentra engine is easy to trap air, but by running engine when filling, and waiting until thermostat opened before shutting off and capping the radiator, I had no trouble filling the coolant-no air was trapped.
Good luck.

Jul 03, 2013 | Jeep Cars & Trucks

1 Answer

What is proper method for flushing the radiator and engine in a 1999 Pontiac Montana?


1: Drain coolant system
2: Purchase coolant flush, making sure you have the proper amount for your size of coolant system
3: Pour coolant flush into your radiator, filling the rest with water
4: On the coolant flush bottle it will tell you how long to run your vehicle
5: Once done running, let cool enough to open radiator cap, and drain system COMPLETELY by first draining out of pep **** on radiator, then taking one side of the hoses off the radiator and draining those
6: Put hoses back on and fill system with coolant. When the fluid gets to the top of the fill port on radiator, start vehicle and let run, allowing air to escape the system, and fill as necessary

Oct 27, 2012 | 1999 Pontiac Montana

1 Answer

Will a leak cause the radiator fan relay curcuit to malfunction on a 2003 jeep liberty 3.7


a leak in coolant system will cause air pocket in the coolant system around the engine coolant temperature sensor.coolant sensor is a thermistor in which when hot cool cause it resistance decrease which affect the voltage from sensor to pcm which will cause engine coolant to turn on.if coolant level okay,check coolant fan fuse and relay, if all is good,engine coolant temperature sensor could be bad or have vechicle code scan for pcm problems it control the coolant fan.fill coolant system to correct level make sure engine coolat reservoir is at full cold mark and not empty.fill coolant system check for leaks,refill coolant overflow jug back to full cold mark dont over fill, if coolant overflow stay empty you have leak either its leaking or you have radiator hoses or radiator leaking coolant.when coolant overflow jug run dry it cause air get in coolant system causing overheating problems.

Jul 25, 2012 | 2003 Jeep Liberty

1 Answer

1993 jeep grand cherokee havc code 06


Chrysler & Jeep Cooling System & HVAC Service: Every car make has its quirks, and Chrysler and Jeep vehicles are no exception. In researching this article, we found several examples of heater problems in these vehicles that seem to be fairly common.

On 2001 and 2002 Sebring Sedan, Sebring Convertible and Stratus Sedan, plus 1993 to 2002 Chrysler Concorde, LHS, New Yorker and 300M, Eagle Vision and Dodge Intrepid models with V6 engines, customers may complain their engine is overheating, or the heater is putting out little or no heat.

Chrysler Technical Service Bulletin 07-002-02 says the problem can be caused by a low coolant level in the cooling system. On these vehicles, air trapped inside the cooling system can displace coolant when the system is refilled. The radiator and coolant reservoir may appear to be full, but there still may be air inside the heater core and heater hoses. This will create a low coolant level that may lead to overheating and low heater output. The bulletin provides a special fill procedure to eliminate the trapped air so the cooling system can be completely filled.

The procedure goes as follows:
1. Obtain Chrysler special tool 8195 (Cooling System Filling Aid). The tool looks like a funnel and attaches onto the filler neck (just as a regular pressure cap does). But it also has a hose clip.
2. Attach the filling aid tool to the cooling system filler neck. Use the clip to pinch off the overflow hose attached to the fill neck. Attach a 4-6' long 1/4" ID clear hose to the bleed valve. Put the end of the hose into a clean container (to prevent coolant from spilling onto the accessory drive belts).
3. Open the cooling system air bleed valve before any coolant is added. If you do not do this, air can remain trapped inside the system and you won't get all the air out. On 1998 and later models with 2.7L engine, the valve is located on the water outlet connector at the front of the engine. On 3.2L and 3.5L engines, the valve is located on the lower intake manifold, left of center under the upper intake manifold. On 1993-'97 models with 3.3L and 3.5L engines, the valve is on the thermostat housing.
4. Pour a 50/50 mixture of coolant and water into the large side of the filling aid funnel. Use distilled, deionized or reverse-osmosis purified water, not ordinary tap water, which may contain salt or minerals that could contaminate the coolant.
5. Slowly fill the cooling system through the large side of the filling aid. Watch the hose connected to the bleed valve. When a steady stream of coolant comes out of the hose, close the bleed valve and continue filling to the top of the filling aid.
6. On 1993-'97 models, place a small, clean container below the end of the overflow hose. Then remove the clip from the overflow hose. Any excess coolant in the filling aid will now drain into the overflow section of the coolant bottle or into the container.
7. On 1993-'97 models, remove the reservoir and recycle the excess coolant.
8. Remove the filling aid from the fill neck. Make sure the filler neck and cap are clean, then replace the pressure cap on the coolant bottle.

Note: 1998 and later coolant bottles have two chambers. Coolant will normally only be in the inboard (smaller) of the two. The outboard chamber is only to recover coolant in the event of an overheat and should normally be empty - except for the coolant drained from the filling aid. This coolant will be drawn back into the pressurized side of the cooling system over time.

Hope helps.

Jan 12, 2011 | 1993 Jeep Grand Cherokee

1 Answer

How do I change the coolant? there is not a radiator cap to pour the coolant in after the coolant drains


you fill it through the resivior, after you drain it you then fill resivior and it will fill engine from there.

Aug 09, 2010 | 2006 Ford Ranger

1 Answer

Just been given a friends car to drive - Daewoo Lanos and I would like to check the water... where do I fill it? I can see the Coolant tank and the windscreen well but cant seem to see where to fill...


Dont use water. Pressurized system requires coolant/water mixture to maintain proper boiling point. Coolant is added to coolant tank you have identified, there is no direct fill to the radiator, it fills out of the coolant tank.

Jul 07, 2010 | 2001 Daewoo Lanos

1 Answer

Coolant leak front under oil fill cover s engine


OK, 4.3 V6 ? Coolant leak is coming from under the oil fill cover ? , do you mean the oil fill tube ? Could be a bypass hose is leaking, or a manifold gasket is bad, need more info maybe, pics

Feb 01, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Cant find vent screw for coolant system on 94 ford 4.6 v8


You shouldent need a coolant vent screw in a v8 water system as fill 1/2 way with coolant ,start engine with HEATER turned to Hot and at idle carry on filling slowly.
Fill to normal level and go....

Sep 23, 2009 | Ford Thunderbird Cars & Trucks

2 Answers

Where is the drain valve on 2002 dodge caravan radiator?


its a pitcock facing the cab bottom of the radiator, plastic flat. once you find the pitcock just put a bucket underneath and turn it.then refill. if you want to flush(run fluid thru to clean it out) the radiator id suggest taking it in. you dont have to flush it every time you change the coolant out.

Mar 28, 2009 | 2002 Dodge Caravan

Not finding what you are looking for?
2005 Chevrolet Malibu Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...