Question about 1992 Ford Taurus

Open Question

How to replace water pump on a 1992 ford taurus

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: How do I change the water pump on a 97 Ford Taurus V-6

detach the cable from the negative terminal of the battery then loosen the 4 water pump pulley bolts be sure to do this before removing the drive belt then remove the drive belt, alternator, and remove accessory drive belts and idler assembly bolts loosen the hose clamp and detach the heater hose from the water pump and then remove bolts from water pump they around $36.00 at NAPA

Posted on Jan 18, 2009

  • 31 Answers

SOURCE: I need step by step instructions to replace front struts.

1.Turn ignition to OFF position to place steering column in unlocked position.
2.Remove hub nut
3.Loosen, but do not remove, three top mount-to-shock tower
4.Raise vehicle on a hoist.
5.Remove tire and wheel assembly
6.Move brake caliper and wire out of the way
7.Remove brake rotor
8.Remove cotter pin from tie rod end stud and remove slotted nut.
Discard cotter pin and nut
9.remove tie rod from knuckle
10.Remove stabilizer bar link nut, and remove link from strut
11.Remove and discard lower arm-to-steering knuckle pinch bolt and nut. (A drift punch may be used to remove bolt.) Using a screwdriver, slightly spread knuckle-to-lower arm pinch joint and remove lower arm from steering knuckle.
12.Press halfshaft from hub
13.Remove shock absorber strut-to-steering knuckle pinch bolt. Using a large screwdriver, slightly spread knuckle-to-strut pinch joint, if required, for removal
14.Remove steering knuckle and hub assembly from shock absorber strut
15.Remove three top mount-to-shock tower nuts and remove strut and spring assembly from vehicle
16.Compress spring with Spring Compressor
17.Place 10mm box-end wrench on top of shock strut shaft and hold while removing top shaft retaining nut with a 21mm 6-point crow foot wrench and ratchet
18.Loosen Spring Compressor , then remove top mount bracket assembly, bearing plate assembly and spring.
INSTALLATION
1.Place a 10mm box-end wrench on top of shock strut shaft and hold while tightening top shaft retaining nut with a 21mm 6-point crow foot wrench and ratchet to 53-72 Nm (40-53 lb-ft).
2.Install strut and spring assembly and three top mount-to-shock tower nuts
3.Install steering knuckle and hub assembly to shock absorber strut.
4.Install a new shock absorber strut-to-steering knuckle pinch bolt. Tighten to 98-132 Nm (73-97 lb-ft).
5.Install halfshaft into hub
6.Install lower arm to steering knuckle ensuring that ball stud groove is properly positioned and boot seal is not damaged. Install a new pinch bolt and nut. Tighten to 53-72 Nm (40-53 lb-ft).
7.Install stabilizer bar link to strut and install a new stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft).
8.Install tie rod end onto knuckle.
9.Install a new tie rod end slotted nut. Tighten to 31-47Nm (23-34 lb-ft).
10.Install a new slotted nut retaining cotter pin.
11.Install brake rotor
12.Install brake caliper
13.Install tire and wheel assembly
14.Tighten three top mount-to-shock tower nuts to 30-40Nm (23-29 lb-ft).
15.Lower vehicle and tighten hub nut to 230-275 Nm (170-202 lb-ft)
16.Depress brake pedal several times prior to moving vehicle.

Hope this helps. Good luck !

Posted on Mar 14, 2009

  • 718 Answers

SOURCE: overheating,reserve coolant tank boiling

Ford 2000 Taurus

To solve the problem you have the things to do in this order;

) When the engine is cold top off the radiator with fluid. (When the pump was replaced the fluid should have been also)
) Make sure the radiator fluid has anti-freeze in it. This is also anti boil also !
) Add fluid to the overflow reservoir.
) Make sure the drive belt was replaced on the water pump.
) With the engine running, you can add fluid to the radiator for the first minute or so. You want to get air pockets out.
) Replace radiator cap.
) Let car warm up. When it's hot you should get the radiator fan coming on.
) When it get hotter the air-conditioning fan may come on.
) If the fan does not come on, the heat sensor is probably bad.
) If all fans come on, and it overheats, you may have a bad thermostat. Trace the upper radiator hose to where it connects to the engine. That's where it located.

Do not operate the engine when it overheats, You will damage the head gaskets and cause radiator fluid to leak into the cylinders.
If you smell radiator fluid in the exhaust fumes, it may already be leaking.

Posted on May 07, 2009

gypsycat00
  • 224 Answers

SOURCE: need to replace thermostat 2000 taurus

If it's the 3.0L Vulcan Engine (OHV), the thermostat is on the driver's side of the vehicle. Follow the upper radiator hose back to a metal area with three 10mm bolts. This is the thermostat housing. Undo the bolts, and there's the thermostat. Mark the back of it with the old thermostat in it (if you get one with a jiggle valve, it'll make it easier to put the new one in because the jiggle valve needs to be on top). The thermostat and housing aren't perfectly round, so you'll have to play with it a little to get it to line up. Make sure to change the gasket. The spring side of the thermostat goes into the engine.

The water pump is in the serpentine assembly. It's the larger pulley located toward the firewall. It'll be easiest to remove the water pump if you also remove the coolant recovery tank. The water pump pulley has four 1/2" bolts that you need to take out WITH THE BELT STILL ATTACHED. I can't stress this enough. The belt will keep the pulley in place so that you can remove the bolts. Take the pulley off, then the belt. Remove the heater hose at the top and the radiator hose at the bottom. There are 12 bolts of two diameters (1/2" and 10mm if I'm not mistaken). Tap the heater hose lightly with a soft-faced mallet to break the seal with the gasket. Trash the old gasket. Replace gasket (you can also line the mating surface of the water pump with RTV Sealant, put the new gasket on the new pump, and line the other side of gasket with a second coat of RTV sealant if you want a really good seal). Install the water pump and torque to manufacturer's specs. Attach the pulley to the water pump hand tight and put the belt back on. Tighten the pulley bolts. Put the coolant recovery tank back in place. Fill with coolant, start engine, bleed and check for leaks.

To bleed cooling system: Idle the engine until the thermostat opens (you'll be able to tell bacause the upper radiator hose will be uber hot and you'll feel coolant running through this hose). Squeeze all hoses in the system that you can reach, but don't burn yourself. Stop the engine and let it cool. Open the radiator cap and squeeze the COLD upper radiator hose. You'll see some bubbles in your recovery tank. You might have to monitor your coolant level for a couple of days while the final bits of air are purged through your radiator cap (that's why it's pressurized).

Hope this helps. It's not hard, but it took me quite awhile.

Posted on Jun 27, 2009

c17hydro
  • 2984 Answers

SOURCE: 2002 ford taurus wtaer pump

Removal & Installation 3.0L (2V) To Remove:

  1. Drain the engine cooling system.
  2. Loosen the water pump pulley.
  3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
  4. Remove the accessory drive belt.
  5. Remove the generator.
  6. Remove the bolt and the accessory drive belt tensioner.
  7. Remove the nut, the bolt and the support bracket.
  8. Remove the bolts and the water pump pulley.
  9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
  10. Remove the bolts and the water pump, and clean the sealing surfaces
To Install:
  1. Install the water pump. Tighten bolts in the sequence shown:
    1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
    2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
    3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
    4. Install the support bracket.
    5. Install the accessory drive shaft tensioner.
    6. Install the generator.
    7. Install the roll restrictor bracket, bolt and the nut.
    8. Install the water pump pulley.
    9. Install the accessory drive belt.
    10. Connect the battery ground cable.
    11. Fill the engine cooling system.

9de9feb.gif
Water pump bolt torque sequence (3.0L (2V) engine)

Posted on Jul 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a water pump on a 2004 ford taurus


Wanda, Check out the video and links I posted to see how to remove and replace Taurus water pump.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Install Water Pump Ford 3 0L V6 FWD WP 9038 AW4094
Ford Taurus Water pump Replacement
Need step by step water pump change
2004 Ford Taurus water pump Google Search

May 31, 2016 | 2004 Ford Taurus

1 Answer

Water pump installiaton


Water pump installiaton ford

Dec 02, 2013 | 1992 Ford Taurus

1 Answer

How to remove the water pump drive belt on a 1999 ford taurus dohc 6cyl


here is a video for the sohc motor is it about the same way

Jan 27, 2013 | 1999 Ford Taurus

1 Answer

How to replace water pump on 1992 ford tarus


Water pump diagram of the 3.0 V6
7_8_2012_9_05_16_pm.gif

Jul 08, 2012 | 1992 Ford Taurus

1 Answer

Replace t-state from water pump


For water pump replacement i suggest you to check the help link provided below.

click the link below :----

Water pump replacing procedure for all vehicles?

http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
---------

HOW TO REPLACE A WATER PUMP

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

------------------
How to route Water Pump Belt?

http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

---------
How to replace Water Pump on Car ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

---------
How to Remove Water Pump?

http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

-------
Where is Water Pump located ?

http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

-----------

This will help. Thanks.

Jan 21, 2012 | 1998 Ford Taurus

1 Answer

Need to replace water pump on 2003 ford taurus


For replacing water pump , you also have to remove, accessory belt,timing belt,timing belt cover and other minor components. Removing water pump is not very difficult, but removal of this other components is necessary, then only you can replace water pump. For detailed procedure, click the link below:--- http://technoanswers.blogspot.com/2011/10/water-pump-removal-instructions-for.html -------- This should help.Thanks.Helpmech.

Oct 28, 2011 | 2003 Ford Taurus

1 Answer

No where is fuel filter in 1992 ford taurus


its under the back seat, you have to yank the entire seat to replace it and the pump

Jun 29, 2010 | 1992 Ford Taurus

1 Answer

I had the water pump changed on my 1992 Ford Taurus. Afterwards when the car was turned on it was letting out a lot of white, grey smoke from the tail pipe and the car was shaking. what can be causing it?...


it's quite possible that the head gasket is blown and it's allowing water to enter one of the cylinders and that's a good possibility for the white smoke. It may be that before the water pump was changed that it overheated and allowed the head to blow a gasket.

May 27, 2010 | 1992 Ford Taurus

1 Answer

1992 ford tauras is leaking atifreeze underneath the block, is it


Hi..my name is Keith..and if its leaking up front in the middle..its your water pump..it has a weep hole in the bottom of it..and when the bushing goes bad..the coolant comes out the hole in the bottom of the water pump..but it could be other things..but thats the most likely suspect..if not please write me back and i will help you further

Jul 04, 2009 | 1992 Ford Taurus

Not finding what you are looking for?
1992 Ford Taurus Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...