How to torque transmission pan - 2005 GMC Canyon

12-13 foot pounds

Pontiac Engine Torque Specs

Butler Performance https://butlerperformance.com > p-34888-pontiac-engi...
Pontiac Engine Torque Specs ; Oil Pump Cover Bolts, Engine Oil, 15 ft-lbs. ; Windage Tray, Engine Oil, 15 ft-lbs. ; Oil Pan, Engine Oil, 12 ft-lbs. ; Camshaft ...

Oil and Transmission Pan Bolts. How much torque?

GMForum.com https://www.gmforum.com > ... > 1992-1999
Jun 12, 2003 - the Torque Specifications for the Xmission Oil Pan Bolts are 12-13 Ft. Lbs. Works for me.

Transmission pan Torque spec
Apr 28, 2017
4T65E-HD transmission pan bolt torque values
Feb 8, 2008
More results from www.gmforum.com

2004 Pontiac Sunfire 2-dr Transmission Pan Gasket ...

MyCarSpecs https://www.mycarspecs.com > pontiac > sunfire > 2004
The transmission pan gasket helps to seal in transmission fluid and keep it from leaking everywhere. This will degrade over time and need replacement, ...

..

10 lb/ft

https://www.gmforum.com/2000-2005-90/4t65e-hd-transmission-pan-bolt-torque-values-271861/

https://www.google.com/search?q=torque+on+Transmission+pan+bolts+for+a+2004+Chevy+Cavalier

..

i posted this 2 time this week.

no trans model stated.
one is 70 INCH POUNDS
and other is 100.
why not learn what driveline is on car first, then ask questions.?
ill list 2 here

45RFE
or NAG1

learn that, and we can answer
better , you learn it the learn to use GOOGLE
example
" Jeep 45RFE pan torque"

eg
https://www.google.com/webhp?gws_rd=ssl#q=+Jeep+45RFE++pan+torque


easy huh , lots of others asking the same question, with no FSM
in the shop.

Drain the Transmission Fluid and Replace the Filter
Raise the car with ramps or a floor jack and support it with jack stands. Find the lower cover of the torque converter housing. Turn the torque converter until you find the drain plug. Place a drain pan beneath the drain hole, remove the plug and drain the fluid.
Remove the cooler lines at the transmission and flush them with compressed, low pressure air. Be careful during this step; fluid may shoot from the other cooler line.
Place a large drain pan beneath the transmission. Loosen the retaining bolts on the oil pan with a socket wrench until they are within a few turns of removal. If the seal doesn't break on its own, gently tap it with a rubber hammer. Fluid will drain from the edges of the pan.
Remove the pan retaining bolts when the fluid stops draining. There is still transmission fluid in the pan. Hold the pan carefully and drain as much as you can into the drain pan.
Scape the old gasket material from the mating surfaces on the oil pan and the transmission. Discard the old gasket. Clean the magnet in the pan. Clean the pan and the mating surfaces with a solvent and a clean, lint-free cloth. Replace the magnet and allow the pan to air dry.
Employ a socket wrench to remove the bolt that holds the filter onto the transmission. Some models may have two bolts. Pull the filter and any old seals or gaskets from the transmission. Install a new filter assembly, including any required seals or gaskets.
Put a new gasket on the oil pan and reinstall it on the transmission. Tighten the retaining bolts to 79- to 119-inch pounds with a torque wrench. Replace the cooler lines on the transmission and the drain plug on the torque converter.
OBD Tools 365 Days Shop

look it up, autozone diy or several othrer online

TRANSMISSION FLUID LEAKS,CAN BE FOUND AROUND PAN GASKET.CHECK PAN GASKET,IF IT LOOKS WET AND YOU SEE FLUID DRIPPING AROUND THE EDGE OF OIL PAN, REPLACE PAN GASKET, WHILE YOU REPLACING PAN GASKET REPLACE TRANSMISSION FILTER WHILE OIL PAN OFF.IF TRANSMISSION OIL PAN NOT LEAKING, CHECK TRANSMISSION OIL COOLER LINES GOING INTO RADIATOR YOU WILL LOOSE A LOT OF FLUID THERE ALSO TORQUE SHAFT SEAL WILL CAUSE HEAVY FLUID LEAK WHILE ENGINE RUNNING CHECK OIL COOLER LINES AND LOOK AT THE TORQUE AREA WHILE ENGINE RUNNING YOU WILL SEE FLUID POURING WHILE ENGINE RUNNING THE OIL PUMP PRESSURE WILL PUSH FLUID OUT AT THE LEAKING AREAS.

Check transmission pan & lines 4 leak. Tighten all pan bolts, line connectors & drain plug. U may need a new transmission pan gasket. Any cracks in transmission?

The transmission is not sealed in the v8 I looked up. It's bolted together. Fluid Pan Removal & Installation To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section
2. Raise and support the vehicle
3. Place a drain pan under the transmission fluid pan
4. Remove or disconnect the following:
   • Drain plug and drain the fluid
   • Shifter cable bracket NOTE: The transmission fluid pan gasket is reusable, clean and inspect for damage; if not damaged, the gasket should be reused.
     
   • Fluid pan and gasket
   • Transmission fluid filter
   • Clean and inspect the transmission fluid pan and magnet
   • Converter housing access plug
   • Converter drain plug

To Install:
NOTE: A new converter drain plug must be used to prevent leakage.

1. Install or connect the following:
   • Install the converter drain plug. Torque to 89 in-lbs (10 Nm)
   • Install the converter housing access plug
2. Lubricate the seals and install the transmission fluid filter. Torque the bolts to 89 in-lbs (10 Nm)
3. Install the oil pan magnet in the transmission fluid pan NOTE: The transmission fluid pan gasket is reusable, clean and inspect for damage; if not damaged, the gasket should be reused.
   
4. Install the transmission fluid pan and gasket and loosely install the screws.
5. Using a crisscross sequence, torque the screws to 8 ft-lbs (11 Nm)
6. Install the shifter cable bracket. Torque bolts to 18 ft-lbs (25 Nm)
7. Install the drain plug. Torque to 19 ft-lbs (26 Nm) NOTE: It will be necessary to hold the drain plug (larger plug) with a wrench when removing the fluid level indicator plug.
   NOTE: Use 3/16 inch Allen key to remove the fluid level indicator plug. Remove the fluid level indicator plug.
   
8. Verify the transmission fluid level

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

10 ft lbs no real patterm needed