Question about 2004 Ford Freestar
All the ford radios have to have a special tool to get them out. you can pick them yup at a parts store. The tools are U shaped and go into the holes on each side of the radio. Just push them in untill you hear/ feel them click into place. most times you can pull the radio out with the tools, some times they need help. Gently pry on the side with a screwdriver and it will come out.
Posted on Nov 10, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2004 ford freestar drivebelt
All you need is a 13mm boxed end wrench. The tensioner pulley is the one all the way on the bottom towards the rear of the van. You can reach it under the van. Slide under the van in front of the passenger front tire and you will wee the pulley. Put the wrench on the bolt and pull towards you to release the tension on the belt.
Posted on Feb 08, 2009
The code is on the fuse box under the dash near the hood release. On my van there are two bar codes on a sticker attached to the fuse box. Under the first bar code, on the right side is the 5 digit code (bring your glasses the numbers are really small). After you get this code, just search the internet and there are plenty of forums on programing the keyless remote and also adding your own unique number to the key pad entry.
Posted on Aug 29, 2009
The procedure is as follows:--
Step 1. Open the tailgate fully.
Step 2. Remove the plastic surround which is part of the housing for the lever which opens the tailgate from the inside. This surround is held by one plastic lugs. The center of these lugs is found at- TOP EDGE ie edge closest to glass. One lug can be found in from each side. The third lug is in the middle, from the edge.
SIDES: One lug on each side down from each top corner.
BOTTOM: (4 lugs in total) One lug can be found in from each side.
Start at the top right corner by sliding the flathead screwdriver between the carpet trim and the plastic surround from the side. Push the screwdriver in firmly and gently twist at the same time. You will feel the lug come free. Repeat this process at the center of each lug. The surround will come free. It is fragile; if it breaks,you can get spare lugs at local auto part stores.
Step 3. Move to the bottom of the tailgate. With a 1/4 turn the 4 plastic fasteners can be removed.
Step 4. With the plastic surround removed in step 2, this has revealed 2 torx head screws. Remove them. The only thing holding the complete trim to the door now are the four fragile plastic tabs at the top. DO NOT PULL THE TOP OF THE PANEL. These four fasteners hold the top of the panel at the bottom of the window and fit into slots where the open side faces the top of the door. The trim panel is slid upwards to disengage these fasteners. Before sliding the trim up, you must support the trim while you disconnect a power supply connector on the right hand side. This can be done with one hand. Then slide the whole panel toward the top of the door, working the fasteners out of their slots. This is the only way you will remove this panel without breaking the panel itself. The trim is very light and will now come away.
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.
Posted on Jun 05, 2010
Testimonial: "While your info appears to be very helpful, I have not had the time to try it at this point. I had nothing bad to say concerning this. However, my dad was the one to originally request the info. Can you please resend this information, especially the diagram as it did not come through very large on his computer, to my computer? Email address is: IRIEFROMCA@YAHOO.COM Thanks for your help an support on this request."
Tips for a great answer:
Jul 28, 2015 | 2004 Ford Freestar
Oct 04, 2014 | 2004 Ford Freestar
Jul 08, 2014 | 2004 Ford Freestar
Aug 24, 2011 | 2004 Ford Freestar
Feb 03, 2011 | 2004 Ford Freestar
Jul 16, 2009 | 2005 Ford Freestar
Mar 28, 2009 | 2004 Ford Freestar
472 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: