Question about 1997 Chevrolet Tahoe

2 Answers

My power stering is not working ok i have replace the power stering pump and i have check the sector and it is ok the car work well when it is runing but when i stop it turn hard i have check if it is air in the sistem and notihng

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

Power Steering Fluid Filling & Bleeding

  1. Repair the power steering system.
  2. Turn the engine OFF.
  3. Raise the vehicle so the front wheels are off the ground.
  4. Turn the steering wheel all the way to the left.
  5. Fill the power steering fluid reservoir to the FULL/COLD level and leave the cap off.
  6. Have an assistant watch the fluid in the reservoir while you turn the steering wheel fully to the right and fully to the left at least 20 times. NOTE: On systems with long return lines or fluid coolers, turn the steering wheel from lock to lock at least 40 times.
  7. Add fluid as needed to keep the fluid level at the FULL/COLD level.
  8. Install the reservoir cap and start the engine.
  9. Center the front wheels and lower the vehicle.
  10. Run the engine for about 2 minutes.
  11. Turn the steering wheel in both directions and verify correct power steering operation.

Posted on Nov 10, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 1,851 Answers

The system is designed to only work when the pump is turning and this happens when the engine is running. The system is working as it should.
Gary @ FixYa

Posted on Nov 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mercury Sable 99 power stering problem


ALL FORDS WILL DO THAT THERE IS NO BY PASS IN GEAR BOX OR RACK , WITH ENGINE OFF THEY WILL OVER FLOW. ONLY FORD SORRY TO SAY YOU FIX IT BUT IS ALL THE SAME ..

Feb 16, 2013 | Mercury Sable Cars & Trucks

1 Answer

Have power stering flued but no power stering


If power steering fluid is full, but the belt driven power steering pump's pulley doesn't turn at a good speed, then the power steering won't work properly. Check that the belt tensioner is providing enough belt tension for the power steering pump to do its job.

If the rack and pinion is bad, it may also cause a lack of power steering in your vehicle.

Good luck on this repair.

Jan 25, 2011 | 2003 Pontiac Grand Am

1 Answer

Power stering making noise and hard to drive


check you power steering fluid
then make sure the pump is turning ok with the belt
if all though things are good then replace the pump
hope this helps
give feedback please

Jan 24, 2011 | 1998 Toyota Corolla

1 Answer

I am leaking power stering fluid, is it best to replace the power stering pump or overhaul it replace the gasket


where is the leak coming from gear box or pump,if its the pump,replace whole pump

Mar 25, 2010 | 1998 Dodge Dakota

2 Answers

No power steering however the fluid level is ok.


Hello there:
This is a indication that the power stering pump belt may be may be too loose and needs to be tightened or that air is in the system and needs to be bled off or the pump as failed all together and needs to be replaced ok
So check these solutions that i have provided before you decide to replace the pump ok?
Hope this is very helpful for you
Best regards MIchael

Dec 21, 2009 | 2004 Pontiac Grand Prix

1 Answer

Power stering, changed the pump but still not


The whole power-steering assembly itself is the next thing to look at. I think it is defective, and could be replaced for a rebuilt one.

Dec 03, 2009 | 2004 Mini Cooper

2 Answers

The power steering message came on in my car and I dont know what I need to do??


first of all check to see if you have a leak . second locate your poewer steering resivoir and determine the cap is on and tight open the cap add fluid if it's low make sure to replace the cap securly afterwords

Jun 22, 2009 | 2006 Chevrolet Malibu

1 Answer

Sterring


change the power stering fluid and check the belt i had the same thang happen to me if that doint help u need a new pump

Oct 14, 2008 | 1990 Nissan Maxima

Not finding what you are looking for?
1997 Chevrolet Tahoe Logo

674 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...