Question about 1993 Nissan 240SX

1 Answer

1993 BNISSAN V6 TRUCK CLUTCH PROBLEMS

SHOVED THCLUTCH WHILE DRIVING AND IT HIT THE FLOOR AND WOULD NOT COME BACK UP, HAVE CHANGED THE SLAVE AND THE MATER AND BLED THE DAMPNER. BUT WHEN IPUT IT IN 4TH AND LET OUT THE CLUTCH THE ENGINE STILL RUNS . DO I HAVE TO REPLACE THE CLUTCH?? I HAVE EXTENDED THE PUSH ARM OF THE MATER TO THE MAX BUT IT STILL WONT DIE WHEN ENGAGED.
PLEASE HELP DESPERATE
PRAIRIE SCHOONER

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 359 Answers

Yes unfortunately it sounds like your clutch has gone

Posted on Jun 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch goes straight to the floor


The usual problem is the slave cylinder.

Apr 20, 2014 | 1997 Ford F150 Regular Cab

1 Answer

I have a 1994 Isuzu Rodeo 5 speed V6 3.2L, it'll


Sounds like clutch adjustment or replacement. (Not disengaging the trans fully). Check to make sure you have enough juice in the clutch master reservoir and that there isn't a leak at the clutch slave cylinder first.........

Sep 13, 2013 | Cars & Trucks

1 Answer

No pressure in my clutch 1993 toyota camry


Slave cylinder is in the front you will see brake line going to it.

Nov 28, 2011 | 1993 Toyota Camry V6

2 Answers

Replaced whole clutch and slave cylinder on 1996 Toyota T100 2wd 2mos. ago. Today while driving the clutch hit the floor. I did'nt see any fluid leakage. Any ideas.


Sounds like you need to bleed the system again, or you have an air leak. try bleeding again and just check your fittings for tightness.

Jan 20, 2011 | Toyota T100 Cars & Trucks

1 Answer

My clutch pedal sits on the floor, doesnt come up on its own. I replaced both the master and slave cylinders and the bleeding process is too long. Still no response from my clutch pedal and I am super...


pull up clutch pedal, all the way up. now fill fluid to top, now open the slave cylinder, it should bleed just with gravity. let it drip for a few minutes or until you have to fill it up 2 times. Make sure that when the pedal is all the way up, that the piston is all the way back on the master cylinder. look up at the back of the master cylinder under the dashl. there is an adjustment. you want just very little play between the pedal rod and the piston, just enough that there is some play. but you need some play there. if there isnt any play, adjust the rod.

Dec 06, 2010 | 1993 Ford Probe

1 Answer

My 1993 jeep wrangler clutch keeps giving out even after i bleed the line..any thoughts? it works fine for a little while then goes to the floor again


replace the CLUTCH MASTER and SLAVE assembly! Age of that classic jeep needs NEW CLUTCH MASTER and SLAVE! That part together w/ clutch slave should be change! Personally i have experience replacing the kit only, it didn't last longer than expected and even got me in trouble, and I spend like i bought a NEW one! So its up to you to decide? taaah!

Nov 10, 2010 | 1995 Jeep Wrangler

1 Answer

Clutch Problems in 1993 dodge stealth


It is probably your clutch master cylnder or perhaps the slave cylnder...but it is definetly one of the two, and its best to replace both at the same time.

Dec 11, 2009 | 1993 Dodge Stealth

2 Answers

Having trouble with my 1989 ford f-150 starting, it is a standard tranny, just changed the clutch and slave cylinder the truck started before I did this. The lights work and all the power options, but it...


There is a safety switch off of the clutch pedal so you don't start it with it in gear, and the clutch out. This is adjustable,and sounds like is your problem. Look under your dash for a small switch that is acuated by the pedal.

Aug 21, 2009 | 1989 Ford F 150

1 Answer

Clutch fluid


I would first check for leaks, and if no leaks i would check your master and slave cylinders if they are working properly

Dec 17, 2008 | 1993 Ford Ranger SuperCab

1 Answer

1993 nissan 240sx clutch problems


Did you bleed the system fully after changing the cylinders? Those are the two main components that cause such problems. If you bled the system out, and it still has the problem, then you most likely have a ruptured line somewhere that is allowing air into the system.

Aug 24, 2008 | 1993 Nissan 240SX

Not finding what you are looking for?
1993 Nissan 240SX Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...