Question about 2001 Chevrolet Silverado 1500

1 Answer

What brake ststem do 2001 silverados have? rear brakes

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,035 Answers

Hi. Your 2001 Chevy Silverado is equipped with Antilock Brake System (ABS). You will identify also if your car is equipped with ABS by looking at the instrument panel for a yellow ABS indicator light after you turn on the ignition.

All the best!

Posted on Nov 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Silverado 2500 HD Why Rear brakes don't work after I installed new hydro-boost power booster, master cylinder, calipers, and pads. I bled master cylinder before installing, and brakes beginn


Hello Patricia,

Have you checked the master brake cylinder reservoir for brake fluid loss?

I don't suspect the master cylinder as you have replaced it... but am more suspect of a leaking brake line or fitting which should have
been discovered when you had the system bled.

The only time I ever had a rear brake problem with a 2500 series Chevrolet was due to seized rear brake caliper guide pins...as your calipers are also new that is not your problem.

If your brake pedal feels spongy and travels to the floor board you have air in the system, a brake fluid leak or a failure in the power steering system, such as a broken hose, broken power steering pump drive belt, or failed pump, would result in a loss of pressure to both the hydro-boost and steering.

Find more information here:

. Hydro Boost Power Assist Systems Operation Diagnosis and Repair

Jul 23, 2017 | 2001 Chevrolet Silverado 2500HD

1 Answer

91 suburban drum brakes drag


check brake pad. it must drum fitted.

Oct 27, 2012 | 2001 Chevrolet Silverado 1500

1 Answer

Rear brakes are sticking/not releasing after changing pads and discs. 2001 chevy silverado


YOU HAVE REAR DRUM BRAKES YOU NEED TO TAKE THEM APART CHANGE RETURN SPRINGS AND CHECK WHEEL CYLINDERS ITS ONE OR THE OTHER

Oct 10, 2010 | 2001 Chevrolet Silverado 1500

2 Answers

2001 silverado changed rotors and break still brake pedal goes to floor and makes noise randomly 96000 miles


This will be in the rear,right?The rear are what gives you brake pedal height,so check the rear,this is the most likely cause.

Jan 26, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

Brakes pulsate when i come to a stop


the front rotors are warped,usually because the rear brakes are out of adjustment,causing you to over work the front brakes,change rotors and pads,check rear brakes if you need more help get back to me Thanks Ray,Please rate my fix as i strive to be the best

Dec 07, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

What is the diameter of the rear brake rotor


you can take a tape measure to do so or it should be stamped on the area where it mounts to the hub, stamped in. probably in millimeters(MM).

Nov 08, 2009 | 2001 Chevrolet Silverado

2 Answers

How to change rear brake disk on 01Chevy Silverado


need a torx 55. must remove caliper in the bracket then remove the caliper. Bracket bolts are 17mm I think.

Oct 23, 2009 | 2001 Chevrolet Silverado 1500

2 Answers

Bleeding Brakes on a 2001 Silverado Z71


Tony,

When bleeding brakes after the system has been opened for service (you didn't say if you were doing any work on the master cylinder) you should start with the farthest wheel away from the master cylinder, which is the righ rear. Fill the master cylinder, then have an assitant "pump up" the brake pedal. Tell them to hold it down firmly, then open the bleeder on the wheel cylinder(s). Do not release the brake pedal until you have closed the bleeder valve again. You'll know when the air is out - there won't be any more bubbles. Since this vehicle is 2001, this would be a great opportunity to flush the system. Just make sure you have enough brake fluid (DOT 3 or 4, depending on your vehicle). Good luck!

Mar 15, 2009 | 2001 Chevrolet Silverado

1 Answer

Hot brakes


Take the top off your master brake cylinder to relieve pressure. You may have over-pressured things if you didn't take the cylinder cap off when you compressed the rotors. You said pads, so I assume they are rear disc brakes.

Dec 31, 2008 | 2001 Chevrolet Silverado 1500

2 Answers

2001 Chevrolet Silverado


Bad sensor in one wheel, they are part of the wheel bearing. Could also be a bad abs computer module, either way, not cheap.

Jun 06, 2008 | 2000 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...