Question about Toyota Land Cruiser

Open Question

I have wired up my spy central door locking kit (c-103a) but the remote controls aren't working and i was wondering if there was something you have to do so they work

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Aftermarket installation of remote central locking on 2006 Nissan Navara ST-R

Doesn't matter, I have given up, the existing central locking components are completely different to that of the new kit, I think I will just have to put my tail between my legs and go genuine, getting a Nissan dealership to fit it for me.

Posted on Jul 20, 2008

Ad

SOURCE: peugeot 406 central locking

you need to reprogram the fob

Posted on Oct 07, 2008

  • 1 Answer

SOURCE: Central locking not working, Chrysler Voyager Limited 2005

hi this works on most voyagers disconect the possative terminal on the battery for ten minites excactly then reconnect and happy days your voyager centrol locking should work ok good luck

Posted on Feb 10, 2009

  • 4369 Answers

SOURCE: 2000 Ford Focus automatic door locks quit working.

check fuse 63 first.

Visual Inspection Chart Mechanical Electrical

  • Binding latch mechanisms
  • Binding linkage
  • Misaligned door
  • Central junction box fuse 63 (20A)
  • Damaged wiring harness
  • Loose or corroded connection(s)
  • Circuit
  • Door lock switch
  • Door lock actuator



It could also be your GEM (generic electronic module) which is expensive as it controls a lot of stuff. A scan tool can be used to cehck for fault codes from the GEM.

Posted on Jun 23, 2009

  • 3 Answers

SOURCE: 1999 Audi A3 1.8T Electric Windows and Central Locking Won't work

will your passenger door open with the key and is it just one side that your windows are not working or both. if its just one side it might be your regulator motor in the door thats not working if its both it might be your central locking pump usually in the boot. however if both of them are working fine it could be that your key needs reprogrammed however i think the 1st 2 are more likely to be the problem.

Posted on Jun 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My right side passenger door does not lock automatically anymore. Is there a fuse that operates this.


no all is related to one fuse you can remove the door internal controls and decore and remove center lock motor plug and test two connectors with multimeter with set on 12v and then lock un lock door and check the reading of the multimeter if it read signal then all plugs and wires from central lock control unit to the door central lock unit is okay it this cae you have to replace the door central lock unit with the same if no signal is readed while you lock unlock the door then you have to check central control unit and all wire plus out of it to the door plug

2- you can remove central control unit from driver door and test it in passenger door (usually the same unit ) if it works with lock unlock its then the replaced unit is faulty and needs to be replaced if it not work then check plugs wires from central lock unit (usually found inside driver door ) to the central lock unit in passenger door

3- check signal for said door fro the output of central door unit if no signal then it mean that faulty central lock control unit

Feb 23, 2015 | 2005 Honda Accord

1 Answer

Central locking system


check central locking system fuse it controls all door locks and other acessories.need go to dealership buy remote keys..

Mar 28, 2013 | 2000 Volvo S80

1 Answer

I have a 2002 ford f150 supercrew lariat, my power door lock on all 4 doors dont work and neither switch works, theres is no clicking sound or anything, but the lights on the switch light up, also the...


You can't figure out thing's without knowing how there work , what controls them . In this case a control module .
Principles of Operation

Power Door Locks
The central security module controls the power door lock and keyless entry system. The lock and unlock operation is carried out by supplying ground to the central security module from the door lock control switch. The normal path of the actuators is to ground through the central security module. The door lock control switch will lock and unlock all doors by grounding the appropriate circuit to the central security module. The central security module then supplies power to the appropriate common actuator circuit to lock or unlock all doors.
Plus we don't guess , we test the electrical circuits with a DVOM - digital multimeter or a test light . We use a wiring diagram so we know which part of the circuits to test .

Keyless Entry
The remote transmitter sends a frequency that is received by the central security module internal antenna. Depending on the frequency received, the central security module will lock all doors or unlock the driver door. If the unlock frequency is received again within five seconds of the first unlock, the central security module will unlock all doors.
If the frequency received is for the panic button, the central security module will cycle ground to the park lamp and horn. The park lamps and horn will continue to cycle until the panic button is pressed again or the ignition switch is turned to the RUN position or 2.75 minutes elapse.
Plus we hook up a scan tool that can read codes from the control module , not a code reader for engine codes , won't work ! Need a professional scan tool .Do you know what DTC'S are ? Diagnostic trouble codes !
Central Security Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action to Take B1309 Power Door Lock Circuit Short to Ground Central Security Module Go To Pinpoint Test C . B1341 Power Door Unlock Circuit Short to Ground Central Security Module Go To Pinpoint Test C . B1485 Brake Pedal Input Circuit Short to Battery Central Security Module Go To Pinpoint Test E . B1526 Keyless Entry Circuit Short to Ground Central Security Module Go To Pinpoint Test F . B1629 PRNDL Reverse Input Short to Battery Central Security Module Go To Pinpoint Test E . B2276 Less Than Two Transmitters Programmed Central Security Module Go To Pinpoint Test I . B2425 Remote Keyless Entry Out of Synchronization Central Security Module Go To Pinpoint Test I . - All Other DTCs Central Security Module REFER to Section 419-10 .
  • All door locks are inoperative
  • Battery junction box (BJB) fuse(s):
    • 8 (15A).
    • 115 (20A) (Super Crew).
  • Circuitry.
  • Central security module.
  • Go To Pinpoint Test C .

Seams you lack the knowledge and test equipment to tackle this type of repair . Your best bet mite be to have a qualified repair shop check it out.
So, without testing i couldn't even begin to suggest what mite be wrong . I would only be guessing , as would anyone on here would.

Jul 30, 2017 | Cars & Trucks

1 Answer

Where is the re-set button to program a remote door lock for my 2000 Subaru Forester?


Obtain all keys/remote controls. Remove driver's side kick panel/lower 'A' pillar trim. Connect central locking registration connectors (white) - black wire and black/blue wire Fig. 2 . Unlock the vehicle using the key. Program first key/remote control as follows: Press unlock button Fig. 1 [1], then lock button [2]. The door lock should lock and unlock in sequence confirming programming of first key/remote control. Repeat programming procedure for remaining key(s)/remote control(s). Once the last key/remote control is programmed disconnect central locking registration connectors. Check operation of all programmed keys/remote controls.

Sep 03, 2010 | 2000 Subaru Forester

2 Answers

Central locking on my Toyota RAV4 is working on opening 3 doos only. Driver door not responding to the remote.


The actuator for the power locks is probably frozen or bad, or else the wiring has broken to it. Or, the body control module is bad.

Good luck in fixing this.

Jul 08, 2010 | 2003 Toyota RAV4

1 Answer

1998 camry vienta grande. Central locking does


Your central processor is erratci and givng into wrong commands. Start from exiting one by one from the battery of the remote to the main hand rest., Check for poor connection in the wiring harness specially in the areas of the door hinges where the wires go into the customer control.Also try to find out if any moisture or oil has clogged on to the main Unit.
Hope you have patience.

Jun 28, 2010 | 1998 Toyota Camry

3 Answers

Yaris 2003 remote control lock problem


You need to reprogram the remote. Please se this website:
http://toyotaownersclub.com/forums/index.php?showtopic=85266

Oct 08, 2009 | 1998 Toyota Corolla

2 Answers

2000 Ford Focus automatic door locks quit working. Replaced Central locking module, but still does not work. All of the doors will only work manually. Remote works to open trunk only - will not work on...


check fuse 63 first.

Visual Inspection Chart Mechanical Electrical
  • Binding latch mechanisms
  • Binding linkage
  • Misaligned door
  • Central junction box fuse 63 (20A)
  • Damaged wiring harness
  • Loose or corroded connection(s)
  • Circuit
  • Door lock switch
  • Door lock actuator



It could also be your GEM (generic electronic module) which is expensive as it controls a lot of stuff. A scan tool can be used to cehck for fault codes from the GEM.

Jun 23, 2009 | 2000 Ford Focus

1 Answer

About central locking to upgrade to remote locking syatem


I have a 91 accord i'm going to upgrade it to a remote start system on it. what do you think?

Aug 31, 2008 | 1991 Honda Accord

1 Answer

Aftermarket installation of remote central locking on 2006 Nissan Navara ST-R


Doesn't matter, I have given up, the existing central locking components are completely different to that of the new kit, I think I will just have to put my tail between my legs and go genuine, getting a Nissan dealership to fit it for me.

Jul 20, 2008 | 2006 Nissan Murano

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...