2000 Toyota Land Cruiser Logo

Related Topics:

Posted on Nov 10, 2010
Be the first to answer

I lost all remote my vdj200 so how can i program the new remote 1 toyota vdj 2 one week ago 3 nething

Answer This Question

1 Related Answer

kapishtech

raj somaiya

  • 2272 Answers
  • Posted on Sep 14, 2010

SOURCE: I have a 2001 Toyota

Try resetting the alarm. The procedure is as follows:--- Insert the car key into ignition switch and turn the key to ON position. Now on the driver side there is a valet switch.The valet switch is near the hood release.Turn the valet switch on, then off three times in quick succession. Listen for a chirp from the alarm system. Press and hold the lock and unlock buttons on your wireless transmitter.You will hear the beep.When you hear a long beep from the alarm system at that time release the buttons.Turn the valet switch on, then off again quickly. Turn the key to "OFF" and remove the key from the ignition. Lock the doors with the remote to test the alarm system.It should get reset and function normally. To disarm the alarm this actually requires the Electronic Control Module to be removed and some wiring modifiactions are made.The ECM to alarm wiring has to be disconnected.But this is not advisable,as alarm is for car safety purpose. Thanks. keep updated for any more query.you can rate this solution and show your appreciation.




Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
3answers

I lost remote to my 2007 corolla how do i get a new one if i am not the original buyer
go to any Toyota dealer. They will sell you a new key fob but they also charge extra for programming. Total cost for the key fob and programming will be around $100. any Toyota dealer can do it for you
Read full answer
Apr 02, 2015 • 2007 Toyota Corolla
1helpful
1answer

Keyless remote camry
Toyota is having problems.. Nothing surprises me
Read full answer
May 10, 2014 • 2013 Toyota Camry
0helpful
1answer

Venza remote keyless entry problems
I have the 2010 Toyota Venza push to start. I lost the original key, so i bought a new key with the remote and its was programmed successful but this remote only had the three buttons on it, instead of four buttons ( Including the Hutch button). So i bought another new remote with the four buttons today and I want to know if it will work when i switch the programmed key into the new remote?
Read full answer
Feb 04, 2012 • Toyota Venza Cars & Trucks
0helpful
1answer

How to programme a clone keyless remote for 95 Toyota camry XLE Thanks
1 turn ignition to "on"
2 insert original remote into reader located in the glovebox
3 red security light should come on solid
4 insert new remote into reader straight after taking out old remote
5 new remote is now programmed
Read full answer
Jan 19, 2011 • 1995 Toyota Camry
0helpful
1answer

95 4cly camry sometimes shuts off when gas peadl is depressed. new sparkplugs and wires, new distributor cap and rotor. new fuel filter, pulled code from the computer it said TPS problem replaced that to...
Bad ignition coil. Replace.
Read full answer
Feb 16, 2010 • 1995 Toyota Camry
0helpful
1answer

2000 Celica GT - I can get into the programming mode just fine, but I have tried to program THREE separate remotes and none of them will program. They are used, so I am "rewriting" them, but they never...
I saw this on one of the toyota forums;
1) Getting a Replacement Remote

Look on ebay or google, make sure the remote has the following FCC-ID: bab237131-056

2) Installing the remote (credit to iPal)

1 open door, take key out...

2 insert and remove key from ignition 2 times

3 close and open driver's door 2 times

4 insert and remove key from ignition

5 close and open driver's door 2 times

6 insert key into ignition

7 close door

8 turn ignition from 'lock' to 'on' and back to 'lock'

if you do step #8

*1 time it's for add mode

*2 times for rewrite mode

*3 times for confirmation mode

*4 times for prohibition mode

9 remove key

10 then door lock will cycle 'lock' and 'unlock' a number of times
corresponding to your key cycles in step #8

11 press lock and unlock button together for 1 ~ 1.5 sec then release

12 then within 3 sec press lock button for 1 sec then release

13 if you did correctly door lock will cycle once...

if wrong, twice... then do it over...
Read full answer
Jan 27, 2010 • 2002 Toyota Celica
2helpful
1answer

Lost remote and like to program new remote. HELP. 2000 prado vx.
1. Start with the following conditions: you are in the vehicle a. Key is out of the ignition
b. Drive door is open ( all other doors are closed)
c. Driver door is unlocked (other door locks don't matter)
2. Insert the key into the ignition (don't turn it) and pull it out.
3. Perform these steps within 40 seconds: a. Cycle the power locks 5 times. Use an even pace and try
to go relatively fast. b. Close, then open the drivers door.
4. Perform these steps within 40 seconds: a. Cycle the power locks 5 times (same as before).
b. Turn the ignition to ON then back to OFF.
c. Turn the ignition to ON then back to OFF.
d. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should cycle (automatically)
indicating successful entry into programming mode. Return to step 1
if the locks do not cycle at this point.
6. Perform these steps within 40 seconds: a. Press the LOCK and UNLOCK buttons on the transmitter
simultaneously for 1 second. b. Immediately after letting go of the lock and unlock buttons,
press the lock button by itself and hold for 2 seconds.
Within 3 seconds, the door locks should cycle ( LOCK then
UNLOCK) once-- indicating successful programming. If
the door locks don't cycle, or cycle twice. Repeat steps
6a and 6b--this remote has not been accepted. c. Repeat steps 6a and 6b for EACH transmitter that will
operate the vehicle. Including any old transmitters.
7. Close the driver door.
Good luck and hope this helps.
Read full answer
Nov 04, 2009 • 2000 Toyota Land Cruiser
2helpful
1answer

How do i program a remote control for a 1998 toyota vienta
1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works
Read full answer
Aug 04, 2009 • 1998 Toyota Camry
0helpful
1answer

How can I re active the wireless remote control system ?
sit in car all doors closed put key in ignition and turn from OFF to ACC 3 times as fast as you can leaving it in ACC on the last cycle then press your remote button. your blinkers should flash to tell you this has worked.... may take you a couple of tries to get it!!
Read full answer
Jun 30, 2009 • 2002 Toyota Camry Solara
1helpful
1answer

Programing a new remote
Use these instuctions if your Deville has an Analog Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Panel (CCP) simultaneously.
(Instrument Panel Cluster (IPC) will light all telltales, then go blank) System is now in diagnostic mode.
Press PASSENGER COOLER button until “RFA” is displayed, then press FAN UP.
If “RFA DATA” is displayed, press FAN DOWN.
If “RFA OVERRIDE” is displayed, press FAN UP.
2. If “RFA 500 NO OVERRIDE” is displayed, press FAN DOWN.
If “RFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.
3. IPC will show “0” on right side of Driver Information Center (DIC) display.
Press warmer button on climate control unit until “99” is displayed.
4. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.
5. To program a second remote, press FAN DOWN button until “RFA 502 PROGRAM FOB #2” is displayed, then press
FAN UP. Repeat step 4.
To exit system, press AUTO, MODE UP, MODE DOWN, or RESET.




Use these instructions if your DeVille has a Digital Instrument Cluster
 1. Press OFF and WARM buttons on Climate Control Center (CCC) simultaneously. Instrument Panel Cluster (IPC) will
light all telltales, go blank then enter DIAGNOSTIC MODE. Press FAN DOW button to scroll through system until
“RFA” is displayed, then press FAN UP button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then
press FAN UP button. When “NO OVRD RF 500” is displayed, then press FAN UP button.
2. When “PGM FOBL 501” is displayed, press WARM button and “99” will be displayed in left upper corner of IPC just
below odometer. System is now ready to program remote.
3. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.)
4. To program second remote, pres FAN UP button until “PGM FOB2 502” is displayed, then follow steps 2 and 3 to
program second remote.
To exit system, press RECIRC or RESET buttons.

Disclaimer
Read full answer
Apr 25, 2009 • 1998 Cadillac DeVille
Not finding what you are looking for?

View Most Popular

2000 Land Cruiser

  • Cars & Trucks

Related Question

I lost remote to my 2007 corolla how do i get a new one if i am not the original buyer

  • 2007 Toyota Corolla

Related Topics

132 views

Ask a Question

Usually answered in minutes!

Popular Questions

Toyota Land Cruiser Prado (LC90) Owner's Manual (free download)

2000 Toyota Land Cruiser

Timing belt light of Toyota LandCruiser 2006

2006 Toyota Land Cruiser

Toyota Land cruiser. Will not

Toyota Land Cruiser Cars & Trucks

Injetor pump removal for 1hz diesel

1992 Toyota Land Cruiser

Landcruiser 79 air con not working

2000 Toyota Land Cruiser

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Toyota Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. 2000 Land Cruiser Manual

2000 Land Cruiser

Loading...