Question about 2000 Ford Windstar

1 Answer

2000 ford windstar

How do i remove the water pump

Posted by on

  • Anonymous Jan 15, 2009

    DOES ENGINE NEED TO BE JACKED UP TO REMOVE WATER PUMP?

  • Anonymous Feb 05, 2009

    How do you get this off the engine?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

It would be best to drop the engine, but can be done by only removeing 3 of the engine support bolts (only loosen the the one under the drivers seat) when the alternator and bracket is removed and idler bracket is removed you can take all bolts out of the water pump and by prying the engine to the drivers side the water pump will just barley come off.

I just completed this very job it took me about 5hours!! good luck

Posted on Feb 11, 2009

6 Suggested Answers

chuck943
  • 783 Answers

SOURCE: 2000 ford windstar anti theft light flashing vehicle won't start

This means that your key is not being recogonized.Ethier the chip in the key is bad or the patts transciever at the lock cylinder. Do you have a spare key? If not you will have to get 2 new keyss cut and programmed.

Posted on Feb 16, 2009

emissionwiz
  • 70365 Answers

SOURCE: i have a 2000 ford windstar no heat still

the problem (which is all to common on Windstar and Explorer) is the air temperture control blend door actuator motor is defective, this motor is what moves a door that gives hot, cold or a blend of hot and cold air blend to give u the desired outlet air temp.

Posted on Feb 27, 2009

localwonder
  • 6784 Answers

SOURCE: remove fuel pump from tank ford windstar 98

To gain access to the fuel pump, it is necessary to remove the fuel tank.

  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump module attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump module locking ring counterclockwise using a locking ring removal tool or a brass drift and remove the locking ring.
  4. Remove the fuel pump module.
  5. Remove the seal gasket and discard it.

To install:
  1. Put a light coating of grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
  2. Insert the fuel pump module into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  3. Install the tank in the vehicle.
  4. Install a minimum of 10 gallons of fuel and check for leaks.
  5. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi.
  6. Check for fuel leaks at the fittings.
  7. Remove the pressure gauge.
  8. Start the engine and check for fuel leaks.

Posted on May 27, 2009

  • 3600 Answers

SOURCE: lower radiator hose connecting tube to water pump.

remove the radiator hose remove the two bolts that hold the tube on and buy new tube and replace is in reverse order.

Posted on Jun 17, 2009

  • 270 Answers

SOURCE: power steering pump on a 2001 ford windstar

There is a special tool for that. It should be available at most auto parts stores.

Posted on Oct 17, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water pump relacement 2000 ford windstar


I have the information you require but I need to know what size motor is in your van. You can get back to me through the Reply box or window below .

Dec 16, 2010 | 2000 Ford Windstar

1 Answer

Replace oil pump on 3.8 Ford Windstar. Do I need any special tools or just remove lower water hose?


water hose? its a lot more involved than that. if it needs an oil pump...it needs more than that. have a shop check it out.

Dec 05, 2010 | 1996 Ford Windstar

1 Answer

I need to know where is the oil presure switch of a 2003 ford windstar 3.8l


On a 1996 3.8 L Should be under the power steering on the block. Looking at the pulleys on the right side just above the oil pan. This would involve removing the pwr steering punp and hoses.

I don't know if a 2003 is different.. You could inspect the area visually to check it.

To get to replace it...
96 - 98 windstar 3.8 oil pressure switch is located under power steering pump. Remove serpentine belt and alternator. Remove PS pump pulley with special puller to get access to PS pump bolts. Drain PS pump and remove PS hoses. Remove PS pump.

Nov 30, 2010 | 2000 Ford Windstar

1 Answer

Replacing belt on 2000 ford wingstar(diagram) 3.8litre engine


6a0c58e.gif


Item Part Number Description 1 8620 Drive belt 2 3D673 Power steering pump pulley 3 8A528 Water pump pulley 4 10300 Generator pulley 5 6C348 Idler pulley 6 2E884 A/C clutch pulley 7 6B321 Crankshaft vibration damper pulley 8 6B209 Drive belt tensioner

Aug 12, 2010 | 2000 Ford Windstar

2 Answers

Describe where the transmission pump is on a 2001 ford windstar van


it is inside the transmission case in the front of the trans

Mar 11, 2010 | 2000 Ford Windstar

1 Answer

2000 Ford windstar engine is making a rattling sound after replacing a serpentine belt which may have been damaged by water pump freezing overnight although water pump is fine


Check all the pulleys for play in the bearings of the pulleys,and check the water pump play,pin the water pump by hand to see if it is it.The frozen water pump,will leak,most likely,hope the engine is o k.

Jan 29, 2010 | 2000 Ford Windstar

1 Answer

Lower radiator hose connecting tube to water pump. how do i remove and replace old metal tube 2000 ford windstar


remove the radiator hose remove the two bolts that hold the tube on and buy new tube and replace is in reverse order.

Jun 17, 2009 | 2000 Ford Windstar

1 Answer

Power Steering Pump


you need an 18mm crows foot wrench 12" 3/8 extention N ratchet N 10mm socket. remove the belt, use crows foot to remove the pressure line, remove other tubes, remove 4 10mm bolts and pluck the pump out, go to autozone or some large chain auto parts store and buy a pully remover/installer use it then bring it back,( they have a loaner program) without the puller you will never get the pully off.

Apr 11, 2009 | 2000 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...