Question about 2000 Jeep Grand Cherokee

3 Answers

Blower motor resistor, where is it located/ - 2000 Jeep Grand Cherokee

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 5,332 Answers

It will be up under the dash on the passenger side near the blower motor. It will have 5 or six wires in its connector

Posted on Nov 10, 2010

Testimonial: "yes you were right thanks alot "

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 749 Answers

The blower motor resistor is located on the passenger side under the dash within a few inches blower motor.

Posted on Nov 10, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,168 Answers

Hello Tireman.

The blower motor resistor is mounted to the bottom of the heater-A/C housing, under the instrument panel and just inboard of the blower motor.

REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Depress locking tab and unplug the wire harness connector from the blower motor resistor or controller (power module).
  3. Depress locking tab and unplug the resistor or controller connector from the blower motor.
  4. Remove the 2 screws that secure the blower motor resistor or controller to the heater-A/C housing.
5.Remove the blower motor resistor or controller from the heater-A/C housing.

INSTALLATION

  1. Install the blower motor resistor or controller to the heater-A/C housing. The housing is indexed to allow (controller/power module) mounting in only one position. Tighten the mounting screws to 2.2 Nm (20 in. lbs.) .
  2. Plug in the wire harness connector to the blower motor resistor or controller.
  3. Plug in the connector from the blower motor resistor or controller to the blower motor.
  4. Connect the battery negative cable.
There you are, I hope your repair goes well.
Thank you for using FixYa.

KL

Posted on Nov 10, 2010

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: locating heater blower motor resistor

the resistor is behind your glove box. open the box and push in the sides to release it and let it hang down...the resistor is right there. I didn't try to replace it, a friend did it, but the part was under $20.

Posted on Feb 01, 2009

michigan man
  • 3533 Answers

SOURCE: 03 Santa Fe blower motor resistor replacement

the part you need to replace is the blower motor resistor assembly it has a screw on each side of it with a plug in th middle and for the most part it is on the passanger under the dash behind a black cover stop by a auto store and take a look at one and then you know what you are looking for and at the same time you can find out how much its going to cost i am only going to guess it somewhere around $15.00 to 25.00 dollars.

Posted on Feb 14, 2009

  • 2 Answers

SOURCE: how to replace a blower motor resistor in a 2004 jeep liberty

You have to take the glove box off and it is right behind it, need a #20 Torx to take it replace it. The glove box is the hardest part of the job, I just replaced mine on an 05 Grand Cherokee but it didn't fix it for me, was well worth the $8.60 to try though.

Posted on Apr 06, 2009

  • 4 Answers

SOURCE: have to change blower motor resistor where is it located

Located behind glovebox. 2 screws and 2 plugs. very simple

Posted on May 30, 2009

  • 412 Answers

SOURCE: help with location and replacing blower motor resistor

depends on what year van..1996-2000,located in engine compartment just above right strut tower at firewall..2001-2007..located behind glove box

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 mustang blower motor resistor location


The blower motor resistor can be accessed from below the RH side of the instrument panel.
  1. Disconnect the blower motor resistor electrical connector.
  1. Remove the 2 blower motor resistor screws.
  1. Remove the blower motor resistor.
  1. To install, reverse the removal procedure.

Feb 21, 2015 | 2005 Ford Mustang V6

1 Answer

Need to locate the motor blower resistor for my 1999 mercury mountaineer, it has dual air, the resistor for the back is fine but the one in the front is bad and i cannot locate it. Please help.


If you have a manual system, you have a resistor. If electronic, you have a blower motor speed controller. Please rate if this helps.

here is info:

Control System Outputs-Manual A/C
Blower Motor Switch Resistor
The heater blower motor switch resistor has the following features:
  • The assembly is located on the evaporator housing in the engine compartment.
  • Three resistance elements are mounted on the resistor board to provide four blower motor speeds.
  • Depending on the heater blower motor switch position, series resistance is added or bypassed in the blower motor circuit to decrease or increase blower motor speed.
  • An overheating protective device (thermal limiter) will open the resistor coil circuit when the temperature reaches 121°C (250°F) interrupting the blower motor operation in all speeds except HI.
  • The thermal limiter cannot be reset and is not serviceable.
Control System Outputs-EATC
Blower Motor Speed Control
The blower speed control is located on the evaporator housing in the engine compartment.
  • The function of the blower motor speed control is to convert low power signals from the electronic automatic temperature control module to a high current, variable ground feed for the blower motor (18527).
  • The blower motor speed is infinitely variable and is controlled by the electronic automatic temperature control module software.
  • A delay function provides a gradual increase or decrease in blower motor speed under all conditions.

Jan 10, 2011 | 1999 Mercury Mountaineer

3 Answers

How doi locate the resistor for a blower motor on a 1997 gmc sierra 1500


Hi!!
Check under dash, passenger side, if necessary, remove cover to access Blower Housing Assy., the harness has two terminals, one for the Blower Motor and one for the Blower Motor RESISTOR which is fastened by two 7 or 8 mm. screws to the Housing.
Here is a picture of the Blower Housing Assy. showing the Resistor.
1kbron_100.gif
Good Day!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Dec 18, 2010 | 1997 GMC Sierra

2 Answers

I need to locate my blower motor resistor on my 1999 S-10. do u know where it is located on my s-10?


The resistor is located under the hood on the passenger side. At the back of the engine compartment you need to locate the airbox it can be identified by a circular piece that's right beside the fender on the firewall (this is your blower motor) to the right if it (looking from the front of the truck) about 4 -6" you will see a wire plug. Unplug this connector and locate the four screws that attach it to the air box. Remove these screws and pull the resistor from the housing.

Hope helps (remember to rate this answer).

Dec 13, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

My 94 Sundance heater/AC blower motor has quit. I've bought a new resister, but cannot find where it's located. Any help?


The blower motor resistor is located in the same duct that the blower motor blows through. If you see the blower motor, within a foot of it is the resistor. The blower motor actually blows over the resistor to keep it cool. The blower motor is usually only in 1 of 2 different locations. On passenger side, access under the hood or under dash access behind glovebox. In both cases the resitor will be in the duct that the blower motor blows through.

Jun 16, 2010 | 1994 Plymouth Sundance

1 Answer

1999 grand marquis were the blower motor resistor is located


this is for manual heater system. If you have electronic (digital display) you don't have one. Instead you have a blower motor speed controller.

here is info

Control System Outputs—Manual A/C
Blower Motor Switch Resistor
The heater blower motor switch resistor has the following features:
  • The assembly is located in the engine compartment on the evaporator housing toward the center of the vehicle.
  • Three resistor elements are mounted on the resistor board to provide four blower motor speeds.
  • Depending on the heater blower motor switch position, series resistance is added or bypassed in the A/C blower motor circuit to decrease or increase A/C blower motor speed.
  • An overheating protective device (thermal limiter) will open the resistor coil when the temperature reaches 121°C (250°F) interrupting the blower motor operation in all speeds except HI.
  • The thermal limiter cannot be reset and is not serviceable.

Dec 12, 2009 | 1999 Mercury Villager

1 Answer

2005 Kia Sorento only blows hot and cold air on high. Is it a blower motor resistor and if it is where is it located?


If the blower moter only works on hi speed it is the blower motor resistor that is bad. The blower motor resistor is located under the passenger side of the dash next to the blower motor. It is not necessary to remove the blower motor to change the resistor.

May 12, 2009 | 2005 Kia Sorento

1 Answer

Blower motor fuse is located 99 mercury cougar


SECTION 412-04: Control Components 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Blower Motor Resistor Removal
  1. Remove the upper footwell trim panel (passenger side).
    • Remove the pushpins.
  1. Disconnect the blower motor resistor electrical connector.
  1. Remove the blower motor resistor.
-------------------------------------------------------------------------
f9d16f6.gif

May 06, 2009 | 1999 Mercury Cougar

1 Answer

Where is the heater blower motor resistor located


if you locate the blower motor the rester is the wire that atachec to blower motor fallow wire till you find a circuit bord this is ur resistor

Dec 06, 2008 | 1999 Mercury Villager

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

1,874 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...