Question about 1998 Pontiac Firebird

1 Answer

What has to be removed to replace ignition switch on a 98 firebird?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Remove steering column cover on the bottom.

Posted on Nov 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the ignition cylinder in my pontiac firebird 1996


You will have to remove all the cowlings from the steering column to access the ignition lock and switch. With the correct key inserted and selected to, probably, the ACC position, you should be able to push on either a pin or a tongue that protrudes from the switch into the housing and the pull the whole lock/switch mechanism out.

May 06, 2011 | 1996 Pontiac Firebird

1 Answer

How to replace a ignition swicth on a 1985 pontiac firebird


Disconnect Negative Battery cable. Disconnect electrical connector from switch. Remove 2 small bolts mounting switch to steering column. Remove actuator rod from switch if on outside, or it may be a knob underneath. New switch will usually be pre-set to "Off" position. Attach actuator rod to switch or mount switch over knob and mount to column with 2 small bolts, being careful not to change switch position while doing so. Re-connect wiring to switch, then Negative Battery cable. Check for proper operation with foot firmly on brake. Make sure that Accessory as well as Start and Run functions operate according to corresponding key position. Switch may need to be adjusted if out of sync.

Dec 05, 2010 | 1985 Pontiac Firebird

1 Answer

How do I remove the ignition switch in my 1969 Pontiac Firebird without the key?


You will need to remove the air bag, steering wheel, air bag coil, lock plate. directional switch to gain access to the retaining hold down screw that holds this lock in place

Nov 11, 2010 | 1995 Pontiac Firebird

1 Answer

How to remove and install new ignition switch into a 1995 firebird


First you have to disconnect your battery, then remove the air bag and all of the goodies in your steering column down to your signal assembly.You then have to unplug the little white and purple wires(this is the security **** that goes to the switch) you then remove the small hex bolt that is holding the switch in place.Pull it out and replace with new switch,don't forget to plug the security wires back up or your car will not start.

Aug 03, 2010 | 1995 Pontiac Firebird

1 Answer

Ignition switch removal in a 1973 firebird.


u have to move the switch,,there should be tree screws Philip head,,

Apr 15, 2010 | 1979 Pontiac Firebird

2 Answers

I cant get to the lower fog light housing on my 98 trans am


yes u get it at the bottom,,u have to remove the splash guards to get to it,,

Feb 20, 2010 | 1998 Pontiac Firebird

1 Answer

2001 pontiac firebird V6.Still wont start.full charge starter good,replaced s-relay replaced ignition switch that was a pain! fuses all good no D-codes.turn key nothing! ignition lock good.running out of...


did you flood if so change iol and filter remove plugs put some oil in each cylinder then turn over about 12 times put new plugs in and should fire

Jan 13, 2010 | 2000 Pontiac Firebird

1 Answer

The 3.8 series 2 engine doesnt turn over with the


sounds like it needs an ignition switch. the reason it dies after a few seconds after jumping the starter is bc the security system from gm thinks you're stealing the car so it kills the fire. the security system goes thru the key so if the switch is bad, it wont run no matter how you try to crank it

Oct 24, 2009 | 1998 Pontiac Firebird

1 Answer

Ignition switch removal


get a proper steering wheel puller, pull the steering wheel off. remove the screw for the hazard switch. remove 1 screw and a metal bracket for the signal switch. remove 3 screws holding the white switch in top of column. Then you need to pull this switch up out of the way, but in order to do this without wrecking it, you need to remove the plastic panels underneith the column to get at the column mounting bolts. there should be 2 13mm nuts holding the column to the dash. remove these. then there should be 4 13mm bolts holding the bracket to the column. remove these and there should be a plastic casing that th wires go through. remove this and unplug the wiring. now you can push the wiring up and out of the way without wrecking your signal switch. now remove 1 philips head screw holding the ignition switch in place and pry it out gently with a flat screwdriver.

installation is reverse procedure of removal

Mar 22, 2009 | 1988 Pontiac Firebird

Not finding what you are looking for?
1998 Pontiac Firebird Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...