Question about Peugeot 604

1 Answer

Where abouts is the thermostat located on Peugeot 806? I think this is the problem as the coolant will not gain any temperature and the mini boiler keeps on kicking in. Please can you help?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,672 Answers

Follow the UPPER RADiATOR hose, in the engine side there is this iNLET where the HOSE is connected, thats the area were u could see the THERMOSTAT VALVE!

Posted on Nov 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the heater matrix on a peugeot 806


Clamp the hoses to the matrix or drain the coolant but you will still get a bit off leakage when you disconnect the hoses in the footwell
remove the glovebox door and the panel below and you can then see the blower housing

Jan 10, 2017 | Peugeot Cars & Trucks

1 Answer

I have a Peugeot 207 (2011) but not a TU engine. I am looking for the coolant temperature sensor which is not located on or in the housing. Please help


Look on google images for 207 thermo switch and see if you recognise something. Its most often in the thermostat housing.

Dec 29, 2016 | Peugeot 207 Cars & Trucks

2 Answers

Peugeot 308 1.6vti enginefan keeps coming on


The engine fan is activated by coolant temperature, and it is normal for it to turn on when the coolant temperature increases. Be certain that your coolant level is correct, and expect it to engage from time to time, especially in warmer weather.

May 08, 2015 | 2008 Peugeot 308 1.6

1 Answer

Code p0128


As you have determined, the P0128 code is related to a low coolant temperature.

This can be one or two issues - the thermostat or the temperature sensor itself. If you're confident that the thermostat was properly replaced - you should probably look into the temperature senor itself.

Here's a video about the P0128 code diagnosing process.



Feb 25, 2015 | Mini Cars & Trucks

1 Answer

What is po 128 in Mini Cooper S?


P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

May 04, 2014 | 2008 Mini Cooper S

1 Answer

Overcooling in winter


IT is an indication that the thermostat is held partially opened and allowing coolant circulation through the radiator resulting to cooler than normal engine operating temperatures . I would have it checked out at a radiator shop as the normal thermostat operating temperature is opening at around 80c and fully opened at 95 c

Feb 15, 2014 | Cars & Trucks

1 Answer

Mini is engine is heating up and no heat in cabin, I want to replace the thermostat but need to know where and how


I think it's right under the coolant fill cap. I have a 2003 mini, and I can see the radiator hose going in there, but it's hard to look in. I copied the instructions from autozone.com and will paste them below. The instructions don't mention it, but I think you will need to remove the air filter housing to access the thermostat housing bolts. Also, there is a bleeder port on the upper radiator hose that I would crack open after the job is done to let any air out. The instructions don't mention that either, but it's always good to bleed the system. Let me know if you have more questions.

If the radiator is filled to the top with coolant and the engine is run without the radiator cap in place, the coolant will expand and spill over as the engine warms up.
  • Drain some coolant into a clean container until the coolant level is below the thermostat housing.
  • Remove the upper radiator hose connection from the thermostat housing.
  • Loosen the housing bolts and remove the housing.
  • Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
  • Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
  • The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
  • When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
  • Install the gasket.
  • Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
  • When the engine has reached operating temperature make sure the thermostat opens.
  • You should be able to see coolant circulating within the radiator.
  • Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
  • If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.
NOTE
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.

Sep 21, 2010 | 2006 Mini Cooper

1 Answer

2002 Blazer. Code 0128 Coolant Thermostat. Coolant Temperature


sound like """"sounds'''like thermostat issue! u might think about starting at that point!hope this helps. John

Dec 22, 2009 | 2002 Chevrolet Blazer

1 Answer

Location of horn (s), Peugeot 806 2.0 HDi (2001)


in the corner of the bumper, i think n/s remove in **** shield or undo from bumper and pull back

Apr 09, 2009 | 2005 Peugeot 405

1 Answer

Peugeot 806 s reg front brakes binding


Flush the brake fluid at the calipers for the whole system. Keep adding new fluid into the master to be sure to flush it all and check to make sure you're using the same DOT spec (3 or 4). Water expands when it gets hot, possibly keeping positive brake pressure at non-braking. Brake fluid absorbs water and the only place to get water is at the seals in the calipers.
Bad flex hoses would be an all-the-time problem, not just at higher temperatures.

Jun 21, 2008 | Peugeot Liberte Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...