Question about 2007 Mitsubishi Outlander XLS

Open Question

Factory passcode reset for hands free phone doesn't work. (Dealer says turn key to on, hold the hangup button for two seconds, release and repeat twice.)

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The dealer lost the key code tag for my 2017 Audi A4 how do I get a new one the dealer does not know how


This is how you can program the key yourself.
1. Press and hold the unlock button on the remote.
2. While continuing to hold down the unlock button, insert the key into the ignition. Turn the ignition to the on position, and keep holding down the unlock button while the ignition is on for approximately two seconds. After two seconds have elapsed, turn the ignition off and release the button. Repeat these steps for each key fob.

Sep 11, 2017 | Audi Cars & Trucks

Tip

Oldsmobile service light 1991-01


Alero

2000-01

Turn the ignition to the ON position, engine OFF. Press the RESET button and release. The CHANGE OIL indicator will start flashing
2000: Press and release the RESET button again.
1999: Press and hold the RESET button until an audible chime is heard and then release the button.


Intrigue


2000-01

Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHANGE OIL SOON indicator flashes two times, the system is resetting. Turn the key off after the the light has finished flashing, then start the vehicle. If the CHANGE OIL SOON indictor comes back on, the engine oil life monitor has not reset. Repeat the procedure again. If the vehicle is equipped with the U20 option code, the vehicle as an oil life low indicator. The oil life low indicator shows an estimate of the oil's remaining useful life. When the oil life index is less than 10 percent, the display will show OIL LIFE LOW. To reset the oil life monitor, press and hold the MODE button until the light appears next to OIL LIFE. Press and hold the trip RESET button until the oil life percentage changes to 99 percent.


Alero,
Intrigue,
Cutlass Supreme


1999,
1998,
1996-9

To reset the "CHANGE OIL" light, turn the ignition switch to the "RUN" position with the engine off. Fully depress and release the accelerator pedal three times in five seconds. The light will flash twice and go out.


Aurora


1995-99

To reset the "OIL LIFE" message, press the "ENG" button with the ignition on until "OIL LIFE PERCENTAGE" is shown. Press the "RESET" button for 5 seconds. "RESET" will appear and then "OIL LIFE" will show 100%


Eighty-Eight,
Ninety-Eight,
Regency


1994-97

When "CHANGE OIL NOW" is displayed, press the "RESET" button. Press "SEL" to display "OIL". Press "SEL" to display oil life. Press and hold "RESET" for 5 seconds. A "RESET" message should display with oil life changed to 100%.


Eighty-Eight,
Ninety-Eight


1992-93,
1991-93

Press and release the "TEST" button on the Driver Information Center. This will illuminate "CHANGE OIL NOW" if it is not already illuminated. Press and release the "OIL" or "OIL INDEX" button. Next, press the "RESET" button and hold for at least 7 seconds.


Toronado,
Trofeo

w/o CRT Display

1991

To reset "OIL LIFE INDEX", press the "2 OPTIONS" button: three times if the vehicle is equipped with a phone and compass, once if equipped with neither. While "OIL LIFE INDEX" is displayed, press and hold the "RESET/ENTER" key at the bottom right of the 15 button switch for 5 seconds.













on Dec 07, 2009 | Oldsmobile Alero Cars & Trucks

1 Answer

I had my oil changed in October after the "oil


Try this procedure and let me know if this does not work;

Turn the ignition switch to the "On" position but do not start the engine.

1. Press the Trip/Reset button until "Setup Menu Hold Reset" is displayed.

2. Then press and hold down the Trip/Reset button for approximately 2 seconds until "Reset For System Check" is displayed then release the Trip/Reset button.

3. Then immediately press and hold down the Trip/Reset button again for approximately 2 more seconds until "OIL 100% RESET IF NEW" is displayed then release the Trip/Reset button.

4. Then immediately press the Trip/Reset button once to display "HOLD RESET IF NEW OIL" then release the Trip/Reset button.

5. Then immediately press and hold the Trip/Reset button again for approximately 2 seconds until "OIL LIFE SET TO 100%" is displayed.

Turn off the ignition switch, and then start the engine to verify that the reset procedure did work, and you might have to repeat the procedure if the Trip/Reset button is not pushed fast enough, or it is not held down long enough, or it is held down too long during the reset procedure, and it may take a few attempts to be successful.

Nov 11, 2010 | 2006 Ford Explorer

3 Answers

MY PT Cruiser Functional transmitter and the one to be programmed both have no "PANIC" Button . How I programme the spare Fob


If you don't have the Panic button then sorry, you can't program yourself, the dealer will have to program it to the RKE (Remote Keyless Entry) module in the vehicle, using their DRB scan tool.

Sep 05, 2010 | 2001 Chrysler PT Cruiser

1 Answer

Ignition is locked, recently changed battery & now can not start truck. tried reseting alarm by unhooking battery, turned steering wheel also played w/ gear shifter to no avail. 2002 avalanche


Turn on the ignition with engine OFF.
Try to start engine, then release the key to ON
Wait 10 or more minutes till SECURITY TELLTALE turns OFF.
Turn OFF the ignition, wait 5 seconds.
Repeat this procedure 3 more times, it takes 30 minutes.
You must turn the ignition key OFF before starting the engine.
To be on the safe side OFF means take the key off, and hold on your hand for 5 seconds.
If you missed something visit GM dealer, and they gladly will provide you a print out of this procedure.

Sep 05, 2010 | 2002 Chevrolet Avalanche

1 Answer

2009 MC300C - I want to reset service message after oil change. I am 150 miles from nearest MB dealer.


Reset “wrench” service light

1.) Turn the key to the on position (do not start car)
2.) Press trip reset button 3 times until service shows
3.) HOLD DOWN reset button
4.) WHILE HOLDING button, turn key off
5.) While key is in off position release the button and repress
6.) Turn key back on holding down the reset button
7.) Wait until service resets

This has to be done in 10 seconds. It may take a couple tries.
Variations include...make sure door is shut and car in neutral.

Sep 12, 2009 | 2009 Mercedes-Benz C-Class

2 Answers

HOW TO RESET SERVICE INDICATOR ON 2001 C CLASS CDI


  1. Make sure the doors are closed
  2. Turn key to position 2,
  3. press trip reset button 3 times, untill service indicator screen shows
  4. Hold down the reset button and turn key to position 0.
  5. while the key is at position 0, release the button and repress,
  6. turn key back to position 2 while holding down the button
  7. wait untill service resets.
this all has to be done within 10 seconds. it may take a few attempts.

Jul 17, 2009 | 2003 Mercedes-Benz C-Class

2 Answers

How can I get rid of the messages on my board....(ie. regular maintenance due)


1. Press and hold trip odometer reset button 2. Turn ignition key to run position KPII (not the start position)
3. Wait 30 seconds or until service light "!" begins blinking
4. Release Trip Odometer button
5. Turn ignition to off position
If that doesn't work try:
1. Press and hold trip odometer reset button
2. Turn ignition key to run position (not the start position)
3. Wait 30 seconds or until service light "!" begins blinking
4. Turn ignition to off position, the service light continues blinking
5. Release Trip Odometer button

should reset it for you

Jul 03, 2009 | 2003 Volvo S60

3 Answers

TWO KEY FOB IS NOT WORKING ONLY ONE


Have all keys with you inside the car and repeat again with the second key within 30 seconds...... "Press and hold the 'unlock' button while at the same time pressing the center 'lock' button three times. On the third time, release the 'lock' button at the same time you release the 'unlock' button." If you have a key with three buttons, ensure doors are unlocked. Put key in ignition and turn key over to 2d position where dash lights, etc come on. Pull key out. Press and hold the "unlock" button while at the same time pressing the center "lock" button three times. On the third time, release the "lock" button at the same time you release the "unlock" button

May 20, 2009 | 2003 Mini Cooper

Not finding what you are looking for?
2007 Mitsubishi Outlander XLS Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...