Question about 1998 Nissan Frontier

1 Answer

Have a miss when running, check engine light on.Change spark plug and wires also dist.cap,rotor.Used scanner said cyliner 2 miss firing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,672 Answers

Check the timing and firing order! U might have mistake in installing those Hi tension wire!

Posted on Nov 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota


I think you have burnt valve seat or head gasket either cylinder head has to be removed

Nov 23, 2013 | Cars & Trucks

2 Answers

I have a 1994 gmc 1500 sierra 5.7 liter v8 truck. Ive change the egr valve spark plugs wires distributor cap. It runs good on the highway no studdering in the engine at all. But at times it may miss a...


Hello: You might check the dist cap and rotor for white powder corrosion. Check the spark plug wires. Make sure wires are not against metal. If you load up the truck does it miss?

Jan 09, 2011 | 1994 GMC Sierra

3 Answers

I changed the spark plugs and wires on my chevy s10 2wd pick up, which is a 4 cylinder and now it will not turn over. I might have the wires mixed up on the distributer cap. Can someone show me a picture...


GET A PIECE PAPER DRAW A LARGE CIRCLE TOP UPPER HALF CIRCLE LEFT TO RIGHT WRITE NUMBERS 1 AND 3 BOTTOM HALF CIRCLE LEFT TO RIGHT RIGHT NUMBERS 2 AND 4 THAT YOUR DISTRIBUTOR SPARK PLUGS WIRES LOCATION.STANDING ON SIDE OF ENGINE WHERE DISTRIBUTOR IS LOOKING DOWN AT DISTRIBUTOR 1 AND 3 FIRST TWO SPARK PLUGS TERMINALS NEXT TO ENGINE. AND 2 AND 4 SPARK PLUGS TERMINAL ON CAP FACING YOU. THIS IS CYLINDERS LOCATIONS STANDING IN FRONT OF ENGINE.RUN WIRES FROM DISTRIBUTOR CAP TO PLUGS TO THE ENGINE SPARK PLUGS.

Oct 17, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

94 royal begis to cut out, chugs at about 55


Replace the spark plugs and wires along with a distributor cap and rotor. Be careful to leave the old wires and plug wires connected to dist.cap, just remove dist. cap from the distributor and lay aside with plug wires on it then install rotor then new cap and proceed to replace each wire for cap and spark plug one at a time so you don't mix up the spark plug wire firing order. Cap laying to the side is used for reference purpose.

Feb 26, 2010 | 1994 Oldsmobile 88

1 Answer

NO SPARK FROM PLUGS


REMOVE DIST. CAP AND CRANK ENGINE SEE IF ROTOR TURN IF IT NOT, CHECK TIMING BELT, IF IT TURNS CHECK FOR SPARK ON DIST. CAP WHERE COIL WIRE GOES IF SPARK CHANGE OUT SPARK PLUG WIRES.IF NO SPARK CHECK IGNITION COIL AND PICK UP COIL.

Nov 05, 2009 | 1992 Volkswagen Passat

1 Answer

1990 K5 Blazer DIED(Electrical?)?


There may be no injector pulse if the computor does not see a RPM signal.
There will be no spark if the ignition module does not see a dist pulse from the dist pickup.......a RPM signal.
Because you do not have both ......I would suggest to check/change the dist pick up.
Follow the wires from the ignition module inside the dist to the pickup which is also inside the dist.
If it is just a bad dist pickup....keep all your old parts as good spares.
Also...is the dist turning? to provide a RPM signal?
You will have to remove the dist to change the pick-up.....mark your timing locations......"rotor position" and "dist body location"before removal.
A quick test before installing the "repaired dist" .....plug it in the the truck wiring and turn on the key....DO NOT CRANK THE ENGINE OR YOU WILL LOSE YOUR DIST ROTOR CORRECT POSITION......as you spin the dist by hand .....the injectors should spray.

Aug 23, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

My 92 automatic 1.8l subie wagon new dist coil wires plugs cap rotor starter. alt is newer still no spark but rotor is turning drove home turned off car did not start again did this the first time and...


try and use the factory recomended coil, incorrect coil can heat up and than not acheive the required discharge to fire the plugs. also will lead to the coil failing, or ECM faulting and throwing a Check Engine Light.

Jul 12, 2009 | 1992 Subaru Loyale

Not finding what you are looking for?
1998 Nissan Frontier Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...