Question about 1998 Isuzu Rodeo

1 Answer

I have to replace the power steering hose on my 1998 4 x 4 diesel rodeo what is the best way to remove it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

The best way I can say is to cut off the line as close as you can at the fitting on each end. Then use a ratchet and a six point socket that will fit the fitting, and remove the fitting. I would spray some WD-40 on the fittings to help get them loose.

Posted on Nov 10, 2010

Testimonial: "Thank you very much. I have been struggling with the lower nut for about 6 hours. I never thought of this Again thank you very much"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I drive a 1998 isuzu rodeo v6. Just wondering what the thing is called that brings the power steering fluid to the tires. I'm assuming that's where it's leaking from. Thanks for any help!


Hi Dillon J
The items name is Power Steering Unit
Your leaking power steering fluid from either the power steering unit, or a hose that connects to the power steering unit...
You need to have it repaired as soon as possible, because if you loose all your fluid it will be almost impossible to steer.
Please rate me
Bud

Oct 29, 2012 | Cars & Trucks

1 Answer

HOW DO I REPLACE THE HIGH PRESSURE LINE FOR A POWER STEERING UNIT ON A 1998 MUSTANG?


Disconnect battery ground cable.
Remove engine Air Cleaner (ACL) .
Disconnect electrical connector in back of engine cooling fan motor.
Remove radiator fan shroud.
Disconnect constant control relay module harness from headlamp harness and place constant control relay module on top of engine to provide accessibility to power steering lines.
Remove wiring harness guide retaining screws and position guide aside.
Remove screw at power steering hose bracket.
Remove anti-rattle clip.
Remove plastic strap retaining tubes to power rack and pinion steering gear.
Remove power steering pressure hose at power steering pump.
Remove power steering pressure hose at power rack and pinion steering gear.
Remove power steering pressure hose from vehicle.
Reverse procedure to install new hose.
Fill and bleed power steering system.

Aug 20, 2011 | Ford Mustang Cars & Trucks

1 Answer

Power steering and brakes quit working on 98 suburban 6.5 diesel


  1. diesel uses what they refer to as hydro-boost to create pwr brake boost
  2. if the p/s and p/ brakes both go out at same time
  3. check p/s belt
  4. fluid level in pwr steering pump
  5. have any repairs been done recently to p/s hoses?

Aug 19, 2010 | 1998 Chevrolet Suburban

1 Answer

1998 silverado...no power brakes or steering


Hydra boost brakes? On a 1500? Is it a diesel? Pump is full of fluid? Can you explain which hose he did this to?

Apr 03, 2010 | 1988 Chevrolet C1500

1 Answer

How to r&r powersteering pump 1998 mercury grand marquis


Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL
  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Oct 04, 2009 | 1998 Mercury Grand Marquis

1 Answer

Do you have the steps to replace the pump


Notes Power steering pump, replacing

Note: As the illustrations in this service information are used for different model years and/or models, some variation may occur. However, the essential information in the illustrations is always correct.

Preparation

Warning: Used fluid is considerably more dangerous than new fluid. Avoid skin contact with the oil.

Remove

  • the oil hose from the mounting on top of the power steering pump
  • the auxiliaries belt.
Note: If there is dirt in the fluid, drain the system and remove the hoses from the steering gear.

Removing the power steering pump/engine strut
Applies only to diesel cars:

Remove

113652509


  • the screw at the pump
  • the screw at the engine.
Leave the strut hanging in the delivery line.

Removing the feeder hose and delivery line
Install

113652510


  • the lock grip pliers on the feeder hose as close to the power steering pump as possible
  • the lock grip pliers on the return hose at the fluid reservoir.
Note: Place paper over the generator (GEN) as protection against oil.

Remove

  • the screw nipple. Remove the delivery line from the pump
  • the hose clamp. Remove the feeder hose from the power steering pump.
Warning: Avoid skin contact with the oil.

Removing the power steering pump
Remove

113652511


  • the 3 screws
  • the servo pump.
Installing the power steering pump
Install

  • the servo pump
  • the three screws. Tighten to 25 Nm .
Installing the power steering pump
Install

  • the feeder hose. Tighten the clamp
  • the delivery line. Do not tighten yet.
Installing the power steering pump/engine strut
Applies only to diesel cars:

Install

  • the strut
  • the screw at the engine. Tighten to 24 Nm
  • the screw at the pump. Tighten to 24 Nm .
Finishing
Tighten the delivery line. Tighten to 25 Nm .
Remove paper and lock grip pliers.
Install the auxiliaries belt.

113652512



Jun 06, 2009 | 2004 Volvo XC90

1 Answer

Location of power steering pump


Usually they are located near or part of the power steering reservoir. Look for the cap to fill the power steering with fluid the pump should be underneath.

May 06, 2009 | 1998 Isuzu Rodeo

1 Answer

Replacing the power steering pump on a 1998 isuzu rodeo


Remove low pressure and high pressure hoses (this one could be hard to break loose). You might want to have an oil pan handy, to capture the oil. Disconnect electrical sensor. Remove the bolt that holds belt tension adjustment plate. And finally remove the bolt that holds the pump in place. It is bolted from the back and located at the right lower corner of the pump if you are facing the front of the car. Remove the pump assy. I could not remove belt pulley at home, no matter how hard I tried. Ended up taking it to an automotive shop and they removed it in no time, using one of those "pneumatic impact guns". Assemble new pump. Fill the reservoir with PS oil. Make sure both of the front wheels are off the ground, start the engine and slowly spin the steering wheel back and forth for about 5 minutes or untill screeching sound stops and the liquid in the reservoir stops foaming. That will bleed any air that is in the system. Don't go all the way to the end of stroke. Good luck.

May 06, 2009 | 1998 Isuzu Rodeo

1 Answer

Lost power steering


power steering pumps can go out w/ no warning. on your model car you can replace it easily if you are handy and patient. loosen belt and hoses. label hoses, remove pump and replace in reverse. hope this helps

Nov 01, 2008 | 1992 Isuzu Rodeo

1 Answer

Power steering pump


not too hard if you have some tools.
  1. Raise and support the vehicle.
  1. Remove the power steering pump pulley (3A733). Refer to the procedure in this section.
  1. Place a drain pan under the power steering pump (3A674).
  1. Remove the power steering pressure hose bolt from the power steering pump. Place the power steering pressure hose (3A719) up and out of the way.
  2. Remove the two power steering reservoir pump hose bolts. Place the power steering reservoir pump hose up and out of the way.
  3. Remove the three front power steering pump bolts.
    1. Remove the rear power steering pump bolt.
    1. Remove the power steering pump from the vehicle.

Aug 21, 2008 | 1998 Mercury Villager

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...