Question about 2003 Isuzu Rodeo

Open Question

Require info for holden rodeo 2.4 litre lg1 engine timing belt specs

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 1994 isuzu holden rodeo injection timing adjustment

try u-pull our patrs

Posted on Sep 12, 2008

Ad
stevenhurc
  • 450 Answers

SOURCE: NEW CLUTCH SLIPPING ON 2004 V6 HOLDEN RODEO

did you bleed the hydralic clutch system on this vehicle? = air in system or not bleed properly.
most of the flywheels for this model were not to be machined...... however it is ok to machine these only slightly but you must machine the surface the clutch plate contacts with the same amount as the outer raised section the pressure plate bolts to.
new flywheels have painted stamped writing saying do not machine...so if hydralic system is ok find out about flywheel.
also may pay to check clamping force of pressure plate most clutch places can do this or some workshops that is if fingers on pressure plate are all at the same height, not broken or cracked..

Posted on Dec 05, 2009

  • 1 Answer

SOURCE: I WOULD LIKE TIMING BELT

motor does half a turn than wants to jam like its got to much comprestion ,motor is brand new, it came with new timing belt and everything timed,but want go and back fires through inlet manifold.

Posted on Mar 27, 2011

emissionwiz
  • 83081 Answers

SOURCE: require info on tensioning serpentine

The serpentine belt is tensioned by an automatic spring loaded pulley, it is a pulley with an arm that moves when the engine is running. Make sure the belt is run over the pulleys correctly according to the routing diagram under the hood, if it seems loose and the automatic tensioner is not defective, also verify you have the correct belt number.

Posted on Jun 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for the crank shaft pulley bolt for a 1989 Holden rodeo


The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault cod es, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

Jun 10, 2018 | Holden Cars & Trucks

1 Answer

Tensioning timing belt


Timing belts usually have an automatic (spring Loaded) adjuster. Usual replacement is done at 100,000 k or 60,000 miles. If you do not replace it you run the risk of it breaking which could do damage to the engine. refer to your owners manual.

Aug 30, 2014 | 1999 Holden Vectra

1 Answer

What could aSwooshing noise from engine area be?


All most sure to be a belt. spray some WD40 or similar on to the belts one at a time ,if it stops you may have to change it. Has the timing belt been changed and tension been checked , if not and it sounds at the engine front, that could be it.

Aug 05, 2014 | 1992 Holden Barina

1 Answer

Timing chain diagram rodeo holden 2007


triple posted.
post country?
post real isuzu engine spec, numbers.!!!
its no jeep , nor is it really a holden, its an ISUZU (mostly)

Jan 27, 2014 | Jeep Commander Cars & Trucks

1 Answer

How many litres of fluid will fill a 1991 holden rodeo transmission?


General advice:Relative
Manual transmission back dif 1,5-2l,front (gear box)3-3,5
Automatic:Over 4l.
Yet,u need to confirm with the dipstick (the one availabile or a rigid wire used as deepstick)
U may take note of what comes out before replacing.
Some transmission need to start the engine and run the trans then ceck level again.
I know is a general advice,but u must treat the cars as a innumerous marks/models and deal fine without factory specs.If not,u need owner manual,dealers visit,shop info,etc.
Cheers let others know if u done it.

Oct 27, 2013 | Cars & Trucks

2 Answers

Hi, i am looking for a isuzu dmax (holden rodeo) 2004 shop manual and parts catalog preferably on CD; engine is a 4HJ1 (orlando at orlando.mah@gmail.com)


this was from 2007 Australia, you can purchase CD from dealers spare parts outlets for workshop manual all light commercial vehicles are covered, infomedia do CD
LCRV SMI Version 2, part no: 92148175 ___ $A320.00
they still do this here

Jul 12, 2009 | 2004 Isuzu Rodeo

1 Answer

Holden 94 rodeo petrol


Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Aug 18, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
2003 Isuzu Rodeo Logo

Related Topics:

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

83081 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14505 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...