Question about 1995 Ford Ranger Supercab

1 Answer

It back fired and when i started up it wont idle, runs at 60 mph without using gas

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Don't know what caused the backfire, but often the pressure from the backfire causes a vacuum line to come off (usually a large one; brake booster, PCV or similar size). this lets extra air past the throttle butterfly and raises the idle speed. find your vacuum leak and the idle speed should return to normal.

Posted on Nov 21, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I disconnected my battery in 08 tundra and now it wont idle


disconecting batt resets the computer. now it needs to learn how to set everything to run again. disconnect batt for atleast 60 seconds, re atach, start car it will start and die(dont press gas) do this over and over until it idles (could take up to 10 times). by pressing the gas you make the computer think it is idling to high so it keeps turning down the idle. it will idle fine after reseting computer and starting several times without hitting gas peddle.

Mar 09, 2013 | 2000 Toyota Tundra

1 Answer

Engine stalls at idle at 35 mph at 60 mph speeds


I think you mean the engine stalls or cuts out at Idle/30/60 mph.
More info wanted,as first is it a Man/or Auto ,what engine have you got 6 or v8??? When last servised by who,How many miles on the clock,dose it smoke when driving or starting ,are the revs ok on idle ,,about what temp dose it run at the 30/60 mph etc etc???
PLEASE send all info, ..
Ron.

Nov 30, 2010 | 1997 Jeep Grand Cherokee

1 Answer

NEED DRIVE CYCLE FOR 2004 CRV TO RESET CAT AND O2 MONOTOR


Here is the info

NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic may not run.

1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge.

Oct 02, 2010 | 2004 Honda CR-V

1 Answer

How do i do the drive cycle on a 1997 nissan pathfinder


The following drive cycle can be used as a guide to assist with re-setting monitors when a vehicle specific drive cycle cannot be located. This OBDII drive cycle begins with a cold start (coolant temperature below 122 degrees F and the coolant and air temperature sensors within 11 degrees of one another). This condition can be achieved by allowing the vehicle to "sit" overnight, and then by beginning the drive cycle the next day. Most drive cycles will be difficult to follow exactly under normal driving conditions, so the driver should exercise caution, road safety, and courtesy to others.
  1. . Start the engine. Idle the engine in drive for two and a half minutes with the A/C and rear defroster on.
  2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle.
  3. Hold at a steady speed of 55 mph for three minutes.
  4. Decelerate (coast down) to 20 mph without braking or depressing the clutch.
  5. Accelerate back to 55 to 60 mph at ¾ throttle.
  6. Hold at a steady speed of 55 to 60 mph for five minutes.
  7. Decelerate (coast down) to a stop without braking.

Sep 17, 2010 | 1997 Nissan Pathfinder

2 Answers

1990 Chevy Scottsdale 1500 wont idle when first starting cold


ICM idle control module, loc throttle body, it may be dirty, remove clean or replace, its easy..

Jul 29, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2001 VW JETTA SPUTTERING AND BACK FIREING WONT GO OVER 10MPH


First check all wires for any thing loose.
The muffler blowing up leads me to think the engine is so far out of time the PCM cant correct it.

REally you need to get it to a good mechanic.

Jun 26, 2009 | 2001 Volkswagen Jetta TDI

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...