Question about Mazda Millenia

1 Answer

How to replace the crankshaft positioning sensor for a 2002 mazda millennium

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 1,420 Answers

Welcome to FIxYa.com


CRANKSHAFT POSITION - SENSOR REPLACEMENT


1. Disconnect the negative battery cable.

2. Remove the idler pulley bracket.

3. Remove the dipstick pipe.

4. Remove the CKP sensor

5. Install in the reverse order of removal.

6. Adjust the drive belt deflection.

how to replace the crankshaft - leedavidian_52.png


Thank you for using FixYa.com

Regards, Lee Davidian

Posted on Nov 09, 2010

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.1 v6 location of crankshaft position sensor at rear of engine. have the exhaust crossover off and other parts as well.


CRANKSHAFT POSITION SENSOR IS BEHIND CRANKSHAFT PULLEY.YOU HAVE TO REMOVE CRANKSHAFT PULLEY TO REPLACE THE CKP SENSOR.

Jun 19, 2011 | 2002 Chevrolet Malibu

1 Answer

Hi my 2001 mazda mpv started staling when come to a stop and had very low rpms when idleing. I ran a obd2 test and the idle air control came up and crankshaft position sensor. I changed IAC with new one,...


After I visited the website named "MPVclub.com," I read an article there that shows the crank position sensor to be located on the right side of the motor buy the crank pulley. You can't miss it, it is right in between the crank pulley and the a/c compressor. Go to www.MPVclub.com, then go to forums, which is on the left hand side of the page, go to 00-06 MPVproblems, go to page 2 and go to the bottom of the page to "PO335 Crankshaft position sensor Replacement, you will see the comments and some pics that will guide you to it.
Hope this helps.

Feb 10, 2011 | 2001 Mazda MPV

1 Answer

WHAT PARTS DO YOU NEED TO TAKE OFF TO CHANGE THE CRANKSHAFT POSITION SENSOR


The splsh gaurds under the car then you should be able to see the sensor its right behind the lower belt pully the hormonic balancer Its easy to replace and will make a world of differance in how the vehicle runs if its bad

Nov 11, 2010 | 2002 Mazda Millenia

1 Answer

My car got FS engine. it cranks but no spark on plugs.replaced another distributor still got same problem.supply is on connector.


TESTING
  1. Disconnect the crankshaft position sensor wire harness plug.
  2. Connect an ohmmeter to the sensor terminals A and B and measure the resistance. Fig. 1: Crankshaft position sensor connector terminals. Measure the resistance across the A and B terminals 89544g27.gif
    Fig. 2: Measure the air gap between the crankshaft position sensor and the crankshaft pulley 89544g28.gif

  3. The reading should be 520–580 ohms at 68°F (20°C).
  4. If not as specified, replace the sensor.
  5. Measure the air gap of the sensor between the crankshaft pulley and the sensor.
  6. Proper air gap should be 0.040–0.080 in. (1–2 mm).
  7. If not as specified, inspect the crankshaft pulley and/or replace the sensor.
prev.gif next.gif

Aug 02, 2010 | 1993 Mazda 626

1 Answer

I need a diagram of the exhaust system on a Mazda 626


0996b43f80203328.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2000 MPV

1 PCM 2 Mass air flow (MAF)/intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Fuel tank pressure sensor 5 Engine coolant temperature (ECT) sensor 6 Crankshaft position (CKP) sensor 7 Camshaft position (CMP) sensor 8 Knock sensor 9 Heated oxygen sensor (HO2S) (front, LH) 10 Heated oxygen sensor (HO2S) (front, RH) 11 Heated oxygen sensor (HO2S) (rear, LH) 12 Heated oxygen sensor (HO2S) (rear, RH) 13 EGR boost sensor 14 Power steering pressure (PSP) switch 15 Main relay


0996b43f8020330c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2001 MPV

1 PCM 2 Mass air flow (MAF)/Intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Engine coolant temperature (ECT) sensor 5 Crankshaft position (CKP) sensor 6 Camshaft position (CMP) sensor 7 Knock sensor 8 Heated oxygen sensor (HO2S) (front, LH) 9 Heated oxygen sensor (HO2S) (front, RH) 10 Heated oxygen sensor (HO2S) (rear, LH)* 11 Heated oxygen sensor (HO2S) (rear, RH)* 12 EGR boost sensor


0996b43f8020330f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart- 2002-06 MPV

May 22, 2010 | 2004 Mazda MPV

1 Answer

Replace crankshaft position sensor


Go to your local auto parts store and by a manual. It will tell you where it is.

May 20, 2010 | 2003 Mazda MPV

4 Answers

Crankshaft position sensor


Sit in the Distributor.

May 14, 2010 | 1992 Mazda MX-3

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

1 Answer

Where crank shaft and camshaft?


The camshaft position sensor is located on the timing cover, near the top of the motor. The crankshaft position sensor is located on the same timing cover near the crankshaft. Just a side note, more than likely the crankshaft position is your issue and it's under a recall from Nissan and they will replace it for free.

May 23, 2009 | 2002 Nissan Altima

1 Answer

Crankshaft Position Sensor On A 1997 Mazda Millenia


No way you need to open the timing belt to get to it , Mazda sucks.

Apr 15, 2009 | 1997 Mazda Millenia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...