Question about 2001 Chevrolet Silverado 1500
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The Best diagram you can get is at alldatadiy.com it has the sections and locations and color of wires with pictures.
Posted on Aug 20, 2009
on the 4.3l version the knock sensor is on the back left side of the engine right by the bell housing. on the bigger engines they are below the intake manifold in the engine valley
Posted on Aug 26, 2009
Not the igniton switch, its the ingition cylinder and or the housing. The switch is not part of what you are really turning. It's connected to it via gears. The common problem is the key gets worn out and the tumblers wear also. Eventualy they do not line up right and will not make the "bar" drop in the cylinder to allow it to turn from the off positon. If you have the title in your name and the key has never been rekeyed or the code has been changed you can go down to a dealership with all of the info for the truck and they can cut you a key from the vin number. You can try that first before you put a cylinder and housing in it.
Posted on Oct 21, 2009
Testimonial: "I really appreciate this info it makes sense and hopefully this solves the problem. it gets really annoying not being able to start the truci"
Disconnect the negative cable from the battery,(WARNING if you have the TheftLock Radio, make the system is off before doing anything that requires the battery to be disconnected)
Remove the radiator upper fan shroud,
Remove the serpentine belt,
Place a drain pan under the hoses to catch the fluid and remove the and remove the hoses from the hard lines coming out of the pump, making a note of which is which, stuff the end of a clean rag into each hose to prevent anything from getting inside it,
Using a pulley removal tool, remove the pulley from the pump,
Remove the four bolts from the rear of the pump( V8 has 4 bolts,V6 has 2 bolts ) and lift the pump out.
Place the pump in it's mounting bracket and install the bolts, tighten them to 37 ft lbs.
Connect the hoses and tighten securely,
Press the pulley on the shaft using a pulley installation tool,DO NOT HAMMER IT ON,, the proper position is the front of the hub flush with the end of the shaft,
Install the serpentine belt,
Install the upper fan shroud,
Fill to the cold mark the correct of NEW fluid,
Re-connect the battery cable.
Bleed the system as follows,
Wheels straight ahead,
Start the engine and allow it to fast idle,
Check for leaks,
Re-check the fluid lever and add more if needed to keep it up to the Cold mark,
Move the steering wheel from side to side several times WITHOUT hitting the stops, this will work the air out of the system, keep adding fluid if needed during this process,
When the fluid level stops going down the system should be free of any trapped air,
Set the wheels straight ahead again and allow the engine to run for 5-10 minutes before shutting it down, re-check the fluid level,
Road test the vehicle and drive it long enough to get it up to normal operating temperature,
Re-check fluid level and fill it to the Hot level.
Posted on Dec 31, 2009
There are 2 knock sensors on these motors. They are located in the valley cover under the intake manifold.
You will have to remove the intake to service them and to even be able to see them.
Posted on Apr 13, 2010
Tips for a great answer:
Sep 12, 2013 | 1999 Chevrolet Silverado 1500
Nov 28, 2010 | 2001 Chevrolet Silverado 2500
Jun 02, 2010 | 1977 Chevrolet Silverado 2500
Jun 01, 2010 | 2001 Chevrolet Silverado
Apr 24, 2010 | 2001 Chevrolet Silverado 1500
Oct 21, 2009 | 2001 Chevrolet Silverado 1500
Oct 10, 2009 | 2001 Chevrolet Silverado 1500
Oct 09, 2009 | 2001 Chevrolet Silverado 1500
223 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: