Question about Hyundai Motor S

Open Question

Changing bulbs on front fascia of Hyundai getz. Where can you get access to chage bulbs for front control panel, i.e heater control,fan etc.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ghost4548
  • 776 Answers

SOURCE: High Level Brake bulb replacement

If memory serves, there are two screws holding this light assy to the rear package deck. They are covered (LH and RH side of this assy). remove the covers and using a phillips screwdriver, remove the screws and lift the assy up and away from the rear glass. you now have access to the bulb and socket.

Posted on May 27, 2009

Ad
ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry 2003 Hyundai XG350

I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

Posted on May 31, 2009

ghost4548
  • 776 Answers

SOURCE: program factory remote keyless entry for 2003 Hyundai XG350

This bulletin supersedes TSB# 02-90-001.
DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:

  • 2001 - 2004 MY Elantra
  • 2001 - 2004 MY Santa Fe
  • 2002 - 2004 MY Sonata
  • 2001 - 2004 MY XG300/350 0390020a.gif
NOTE
  • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
  • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
SHOP MANUAL

PAGES

2004 MY Elantra
BE-73 - BE-74
2004 MY Santa Fe
BE-43 - BE-44
2004 MY Sonata
BE-40 - BE-41
2004 MY XG350
BE-46 - BE-47
KEYLESS ADAPTER CABLE INSTRUCTIONS:
  1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
  2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
    0390020c.gif
  3. Turn the Hi-Scan Pro ON
    and press ENTER
    . NOTE "Release date 29. Sep. 2003" OR LATER
    must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
    0390020d.gif
  4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
    and press ENTER
    . 0390020e.gif
  5. Select vehicle model and press ENTER
    . 0390020f.gif
  6. Select option "TRANSMITTER CODE SAVING"
    and press ENTER
    . 0390020g.gif
  7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
  8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
    0390020i.gif
  9. Press ESC
    on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
  10. Turn the Hi-Scan Pro OFF
    and disconnect the adapter cable from the multi-purpose connector.

Posted on May 31, 2009

ghost4548
  • 776 Answers

SOURCE: hyundai getz radio

Here's a pic

5781d0b.jpg
Pops out, then remove 4 screws which mount the audio & instrument panel.7be2186.jpg

Posted on Jun 05, 2009

  • 1 Answer

SOURCE: CHANGING A FUEL FILTER IN A HYUNDAI GETZ

I have an '03 Hyundai Accent 1600cc. I am told by the techies at the local dealer, the fuel filter is ON the fuel tank. You gain access to it by removing the back seat, then opening the panel beneath the back seat. Replace the filter, screw the panel back onto the floor and the job is done....

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear brake light hyundai getz 2004


Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.

May 15, 2011 | Hyundai Motor 2004 Accent

1 Answer

How do I replace dashboard heater light? The glowing lights that indicate direction of air flow.


Heater light bulb, and all other bulbs for the air conditioning buttons, are on the same mini panel, and attached to the back of the radio front fascia. To dismount this fascia, you need 1) To pry out (no screws) the clock 2) Unscrew the one screw that holds the top of the fascia (screw is hidden behind clock) 3) Unscrew the two screws at the bottom of the fascia 4) Disconnect all connectors from the back of the fascia 5) Look for the burnt minibulb.
You could replace the bulb without disconnecting, but the cables are short, and the possibilities of marring your dashboard are high.

Jun 19, 2010 | 1999 Honda Accord

1 Answer

How do you remove the air filter box on a 2001


REMOVAL
Release hood latch and open hood.
Access Rubber Grommet
Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners.
Fastener Locations

Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield.
Remove Push In Fasteners
Remove the push pins attaching the fascia to the upper radiator closure panel.
Headlamp Jack screws

Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s).
Roll Fascia Forward

Roll fascia forward to clear way for headlamp housing removal.
Disconnect wire connector from back of lamp socket(s) and/or bulbs.
Remove Headlamp Housing

INSTALLATION
CAUTION : Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

Place headlamp housing into position.
Connect wire connector to lamp socket(s)
Verify headlamp and signal lamp operation.
Install jackscrews to attach headlamp housing to crossmember.
Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
Install nut on fascia stud through the splash shield access hole.
Verify headlamp operation and alignment


Nov 03, 2009 | 2001 Chrysler 300M

1 Answer

How do I replace fog lights on my 2002 Hyundai Santa Fe?


Look up into the bumper and see if you can access the fog light. The bulb should just twist out of the back. If not, the assembly should either pop forward or back to come out. I've heard though, that many santa fe's require the removal of the entire front bumper fascia just to get to the bulbs in which case you'd have to remove your headlights to get to the screws holding the bumper fascia on

Sep 09, 2009 | 2002 Hyundai Santa Fe

2 Answers

CHANGING A FUEL FILTER IN A HYUNDAI GETZ


I have an '03 Hyundai Accent 1600cc. I am told by the techies at the local dealer, the fuel filter is ON the fuel tank. You gain access to it by removing the back seat, then opening the panel beneath the back seat. Replace the filter, screw the panel back onto the floor and the job is done....

Aug 15, 2009 | 2003 Hyundai Accent

1 Answer

Program factory remote keyless entry 2003 Hyundai XG350


I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

May 22, 2009 | Hyundai Motor 2003 XG350

1 Answer

Programming factory remote on 2003 Hyundai XG350


Again, the remotes can only be programmed by a Hyundai Technician (ETACS - Electronis Time and Alarm Control System).

May 22, 2009 | Hyundai Motor 2003 XG350

2 Answers

How to change hyundai getz brake light in light cluster?


On the Getz remove 2 screws on the outside then gently prise the cluster off from the dowels as above.

Apr 24, 2009 | Hyundai Motor 2003 Elantra

2 Answers

Hyundai getz radio


Here's a pic

5781d0b.jpg
Pops out, then remove 4 screws which mount the audio & instrument panel.7be2186.jpg

Apr 11, 2009 | 2003 Hyundai Tiburon

1 Answer

How do you replace headlamp bulbs on 1999 chrysler 300


You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
Tell me if this works for you?
HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
REMOVAL
  1. Release hood latch and open hood.
  2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
  3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
  4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
  5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
  6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
  7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
  8. Remove headlamp housing Remove Headlamp Housing
INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.
  1. Place headlamp housing into position.
  2. Connect wire connector to lamp socket(s) and/or bulbs.
  3. Verify headlamp and signal lamp operation.
  4. Install jackscrews to attach headlamp housing to crossmember.
  5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
  6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
  7. Install nut on fascia stud through the splash shield access hole.
  8. Verify headlamp operation and alignment

Mar 27, 2009 | 1999 Chrysler 300M

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...