Question about 1997 Mazda 626

1 Answer

Brake rotor to remove the brake rotor do I need to go clockwise\ on the 1 &1/4 is it reversae threaded

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 27 Answers

That 1&1/4 nut holds the axle shaft to the hub. It does not have to be removed to pull the brake rotor. If there are no screws holding the rotor to the hub, it is probably stuck. Tap the area on the rotor between the lug studs with a hammer. This should get the rotor loose.

Posted on Jun 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove front rotor on 2005 sonata


Caliper bolts are regular threaded bolts so you would remove by twisting to the left (clockwise)

Jul 08, 2012 | 2005 Hyundai Sonata

1 Answer

How do you change the rear brakes pads and a caliper on a 2004 XJ8?


you will need to 1st get a caliber turning set from harbor freight, it very cheap maybe 35-40 bucks...you need to raise both rear tires,crank the car put it in neutral so that the electric module releases the brakes from park position,then you disconnect the neg battery term.remove the tires, open the hood,remove the fluid reservoir cap,remove the calibers by the two bolts facing the inside,then remove the pads,then take the caliber tooland lock the two male nipples ends inside the female piston plates(u will see how the fit)now make sure the brace plate of the of the caliber tool is snug and begin turning the tool threaded side clockwise,and the bolt near the plate should be turned counter clockwise and each turn will turn the piston inside the caliber until its all the way flush with the inside of the caliber wall itself...then place the pads inside the caliber rotors are the same as removing from any other car,they may need a good tap with a hammer,some may have one alen head screw.But replace the rotors and pads.Once they are replaced,lower the car,reconnect the neg terminal,put the fluid cap back on,crank the car,pump the brakes and hold the center console lever upuntil the brake light goes off and u will hear the rear brake module engage.Hope this helps!

Sep 28, 2011 | 2004 Jaguar XJR-Series

1 Answer

Replace front hub bearing


Hello,
Remove and tie up the brake caliper take the snap ring off slide toward the end (careful not to launch it into the neighbors gravel driveway). This truck is up on jack stands right! now wipe off the grease and see the lock ring with two philips small bolts remove both bolts needle nose pliers take off the no turn washer now counter clockwise take off the retaining nut the part with the threaded holes and two larger non threaded holes. grab the rotor and pull the brake rotor off and place it in a clean cardboard box to keep dirt out of the hub bearings. Now your going to have to decide how much of this suspension do I replace while I am this dirty. Either top of bottom ball joint ans some times both have to be removed to take out the CV joint front half shaft. Tie rod ends drag links idler arm bushings A frame bushings ball joints all will be worn out on a 25 year old truck.
Thanks

Jun 23, 2011 | Nissan Altima Cars & Trucks

1 Answer

How do i replace rear brake pads off a 1995 ford contour


Check this REMOVAL & INSTALLATION
(see Figures 1, 2 and 3 / click over images for zoom )

CAUTION Older brake pads or shoes may contain asbestos, which has been determined to be cancer causing agent. Never clean the brake surfaces with compressed air! Avoid inhaling any dust from any brake surface! When cleaning brake surfaces, use a commercially available brake cleaning fluid.
  1. Remove 1 / 2 of the brake fluid from the master cylinder reservoir.
  2. Raise and safely support the vehicle.
  3. Remove the wheels.
  4. Remove the cotter pin and guide pin.
zjlimited_1153.jpg

Fig. 1: Rear disc brake components

  1. Remove the caliper locating pin cover and remove the locating pin.
  2. Swing the rear disc brake caliper away from the brake rotor and anchor plate. There is no need to remove the parking brake cable or brake hose.
  3. Remove the inner and outer disc brake pads.
To install:
  1. If installing new disc brake pads, use rear caliper piston adjuster T87P-2588-A or similar tool, to rotate the rear disc brake piston clockwise, retracting the caliper piston. This will allow room for the new brake pads.
zjlimited_1154.jpg

Fig. 2: Removing the parking brake cable

zjlimited_1155.jpg

Fig. 3: Use the adjuster tool to rotate the piston into the caliper

  1. Install the inner and outer disc brake pads.
  2. Swing the rear disc brake caliper back into position over the disc brake pads.
  3. Clean the locating pin threads and apply 1 drop of a thread locking agent or similar sealer.
  4. Apply a small amount of disc brake caliper slide grease to the shaft of the locating pin.
  5. Reinstall the locating pin and torque to 30 ft. lbs. (41 Nm).
  6. Reinstall the guide pin and the cotter pin.
  7. Adjust the parking brake by operating the parking brake control several times.
  8. Reinstall the wheel and tire assembly. Torque the lug nuts to 62 ft. lbs. (85 Nm).
  9. Lower the vehicle.
  10. Adjust the parking brake by operating the parking brake control several times.
  11. Pump the brake pedal several times to achieve a good pedal before attempting to move the vehicle.
  12. Check the brake fluid level in the master cylinder fluid reservoir and add fluid as necessary.
  13. Road test the vehicle and check for proper brake system operation.

Hope this helps (remember to rate and comment this answer).

May 01, 2011 | 1995 Ford Contour

2 Answers

Emergency brake adjustment


There are 2 ways. It has rear drum in hat style brakes, meaning it has pads and rotors for basic brakes, but incorporated in the rotor is a drum with park brake shoes inside. Remove rear pads and rotors, check the condition of the park brake shoes. Tighten the star wheel adjuster while installing the rotor, keep repeating until rotor feels snug pushing on. Repeat other side reassemble. If still doesn't feel tight, there is an adjustment nut on the left rear side on the cable. The nut is where the 2 rear cables meet, it can be tightened. Do not tighten first, if you ever need park brake shoes later they will not allow the rotors to go back on.

Jan 28, 2011 | 2004 Chevrolet Tahoe

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

How to take back rotors off a 1994 honda civic.


PATH: Brakes > Front Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and support the front of the vehicle on jackstands. Remove the front wheels.
  2. Remove the caliper assembly; do not let the caliper assembly hang by the brake hose, instead support it with a piece of wire looped around the front spring or control arm.
  3. Remove the retaining screw from the brake rotor and remove the rotor from the hub.

An impact driver, No. 3 phillips screwdriver bit, and a hammer may be needed to remove the retaining screw. It is fairly easy to destroy the screw slots using an ordinary phillips screwdriver to remove the tightly driven screw (see photo).

  1. To install the disc, replace the disc on the hub, screw in the retaining screw and replace the caliper assembly.
edc2fe7.gif
PATH: Brakes > Rear Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  4. Remove the caliper bracket.
  5. Remove the two 6mm screws and the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly to prevent cocking the rotor.
  6. Install the rotor in position. Install the two 6mm retaining screws.
  7. Install the brake caliper. Install the tire and wheel assembly.

PATH: Brakes > Rear Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  4. Remove the caliper bracket.
  5. Remove the two 6mm screws and the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly to prevent cocking the rotor.
  6. Install the rotor in position. Install the two 6mm retaining screws.
  7. Install the brake caliper. Install the tire and wheel assembly.

4d85ad3.gif

Sep 15, 2010 | 1994 Honda Civic

1 Answer

Which direction to turn nut when removing brake rotors on 1998 Chevy Metro clockwise or counter


All brake parts are counter clockwise. But what nut are you talking about. Not the axle nut? That doesn't come off. Rotor pops off after caliper is removed.

Aug 18, 2009 | 1999 Chevrolet Metro

3 Answers

Rear brakes on 2005 F150


You can't remove the rotors because the emergency brake is tight on the inside of the rotors. Make sure it's not engaged when you are working on the rear brakes. Block the front tires for saftey. Then you have to remove the rear calipers from the mounting brackets, there are two bolts that hold the calipers on. Make sure you hang the calipers securily with some wire so you don't damage the rubber brake line hose. Then you need to adjust the emergency parking brake shoes in order to remove the rotors. Theres a rubber plug on the backside of the rear hubs, once you look at the back of the hub you'll see the plug. It's on the top. Once you take out the plug, you need to use a screw driver to turn the star spindel. You need to turn the star spindel counter-clockwise in order to give yourself enough clearance to remove the rotors. The beauty of this design is that ford incorporated a drum and caliper system together, but it's difficult to take off the rotors if the emergency brake shoes are to tight. The inside of the rotors acts as the drums for the emergency brake system. I've done this and it's not that hard, but, I did have to replace the emergency brake shoes because they were worn out and the shoes fell off the metal backing plates when I finally got the rotors to come off. They only glued these shoes onto the backing plates, they don't rivet them so take your time getting the rotors off or you can damage the emergency brake shoes, but if you do they are cheap at napa. My service guide says to install the new rotors, use a couple of lug nuts to hold it on, then adjust the star spindal for the emergency brake all the way clockwise until you can't turn it anymore, then you must back it off 8 clicks counter-clockwise. Make sure the emergency brake is not engaged when you are doing this, the 8 clicks backwards compensates for when you do engage the parking brake because the shoes expands outwards. This adjustment sets the emergency brakes so they work properly. Once the emergency brake is properly set you can't remove the rear rotors, which is what your initial problem is. Then install the rubber plug back in the hole, put on the new pads and calipers and you're good to go.

Jun 25, 2008 | 2005 Ford F-150

Not finding what you are looking for?
1997 Mazda 626 Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...