Question about Ford Ranger

2 Answers

My 92 ranger is not gettin fire - Ranger Ford Cars & Trucks

Posted by on

  • chelsi_stanl Nov 09, 2010

    Ford ranger isn't getting any spark it cranks but don't get any spark

  • chelsi_stanl Nov 10, 2010

    The motor don't have a distributor it's a 4 cyl. With 8 spark plugs and it's got two coil packs

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi! One thing to consider if there is no spark. Please do check the distributor coil. If the distributor coil is faulty the result will surely no spark to the plugs. Please be sure that the distributor cap and plug wires are good too. Hope this helps and thank you for using FIxYa!

Posted on Nov 10, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

You need several things to make your car run, spark, fuel, compression and all at the right time... ie TDC (Top Dead Center). If all are working, then the car will run. So one is not right and you say it has fire? I assume you mean spark. Check if the compression is ok and all cylinders are 100 psi or approx., then it must be fuel.

Check if you are getting fuel pressure. With a tester at the rail the pressure will be 45psi approx.; if you are getting no pressure then look at the pump and relay. Let us know what you find.

Posted on Nov 09, 2010

  • ZJ Limited
    ZJ Limited Nov 09, 2010

    The ignition module is what turns the coil on and off. This is the
    little box fastened on the side on the distributor. Change this and
    your truck should run.

    I suggest removing the spout connector, (a 2-pin plug in connector in
    the harness near the distributor) and check for spark, or signal on the
    coil negative. Make sure you are checking on the coil negative. If you
    are not sure, unplug the coil and see which wire is positive when the
    key is on. If you have spark with the spout disconnected, then the
    computer is not doing its part...check the fuses and make sure the check
    engine light is working properly. If the spout disconnect makes no
    difference, then make sure the distributor is properly grounded. Also,
    make sure you have power on both sides of the coil when the key is on
    and everything is connected.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am in need of under dash fuse panel diagrams backside power side 92 Ford ranger xlt.


Confused by 'backside power side', but

Just Google

92 Ford Ranger XLT fuse box
And look at the Inage tab.

Or if you are after wiring details

92 Ford Ranger XLT wiring schematic

Jan 26, 2016 | Ford Cars & Trucks

1 Answer

I got a 92 lexus ls400 an im not gettin any fire


Check and see do lights come on when not running. Most likely a dead battery, but jump it and it goes. Bad alternator not charging battery. No power, no go.

Sep 25, 2014 | 1992 Lexus Ls 400

1 Answer

What is the firing order for a 92 ford ranger 3.0 v6


1992 Ford Ranger 3.0 liter V-6 VIN "U"

zjlimited_286.gif


Hope this helps (remember to rate and comment this).

Apr 14, 2011 | 1992 Ford Ranger

3 Answers

Where is the obd plug on an 92 ford ranger


Hi there,

It is called an EEC for a 92 model and it's located next to the fuse panel under hood on drivers side hanging under a little cover.

Glad to be of help...

Jan 23, 2011 | 1992 Ford Ranger

1 Answer

Put a new fuel pump on my 92 ranger. 3.0 l 2wd, itll crank and you kan hear the pump run but wnt fire, any ideas?


your question is to vague.
what made you change the fuel pump. (symptoms)
Always remember an engine needs
  1. fuel
  2. spark
  3. compression
  4. timing
have you confirmed that you are getting fuel and if are
check for spark
and work down the list if one is missing that's your answer

Jan 20, 2011 | 1992 Ford Ranger

1 Answer

What is the firing order on a 92 Ford ranger xlt 3.0 v6


The spark plug firing order is ( 1 - 4 - 2 - 5 - 3 - 6 ) The distributor rotor turns CLOCKWISE ( 1 - 4 - 2 - 5 - 3 - 6 ) The marked # 1 position on the distributor cap faces towards the firewall and slightly towards the passenger side The engine cylinders / spark plugs are numbered : passenger side of engine , front to rear , 1 , 2 , 3 and drivers side of engine , front to rear , 4 , 5 , 6

Dec 08, 2010 | 1992 Ford Ranger

1 Answer

1992 Ranger: where is the starter on a 92 ford ranger...


if it is 5sd it is on the drivers side by the oil filter and it would have three bolts

May 17, 2010 | 1992 Ford Ranger

1 Answer

I have a 91 ranger...it has the 2.3 4cyl...it ran fine then stopped one day when iwas leavin the house...i havent been able to get it to start unless...i spray starting fluid into the intake...ive changed...


i dont think you car wants to leave your house.... maybe your injectors are bad, if the chamber is getting too much fuel you could be flooding it, and if that gas gets past your rings you have bigger problems

Nov 23, 2009 | 1992 Ford Ranger

2 Answers

Firing sequence on a 92 ford ranger 2.3l


The firing order is 1 - 4- 3- 2. I would suggest visiting the autozone.com website and register the truck info. It is free and you will have access to an online repair manual for the truck. Information like this is available there and it's a handy resource for anyone doing maintenance on their own vehicle. Anyway, hope this helped and best wishes.

Sep 10, 2009 | 1992 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...