Question about Mazda 626

1 Answer

How do I get the pistons in on a Mazda 626 2000?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

You can use a "tool for the job" but i have used jubilee clips before now.......just do them up to fit nearly tight then gently tap piston down bore.worked for me.......

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install piston rings mazda protege 1.5 dohc 1998


Do you mean the whole job or just putting the rings on the piston that has been removed and cleaned?? If you mean the whole job then you need a service manual. Also the parts store can show you how to install the rings on the pistons.

Jul 13, 2012 | Cars & Trucks

1 Answer

How do I adjust back brakes on Mazda mx6 I've put


you need to turn the caliper piston while pushing on it at same time.

Apr 22, 2012 | Mazda MX-6 Cars & Trucks

1 Answer

We need pistons rings for a Motor FP Mazda Protege


Go to a engine remanufactory shop and see if they can order you a set. I am sure there web sites that sells piston rings.

Feb 12, 2011 | 2000 Mazda Protege

1 Answer

When fitting new rear brake pads to a 2004 Mazda 323, how do I move the pistons back into the cylinders to accomodate the new pads?


Applying pressure will make the piston go back in but you can kick and release the brake before the job is done , use a wire band to run over the piston to hold it tight so that it does not move off, the pads can be pushed into with the wire holding the piston till in place when it can be taken off.

Sep 30, 2010 | Mazda 323 Cars & Trucks

1 Answer

Mazda 6 2006, rear disc brakes. In trying to replace the pads I could not retract the piston w/ either channel locks or c-clamp. Is there some trick to this? Piston does not seem to be bound as it actuates...


You need to twist the piston as you retract it. I use channel locks to twist and a c-clamp. be careful not to grab nor tear the piston boot.

Mar 17, 2010 | 2006 Mazda 6

1 Answer

REAR CALIPER


Try cracking open bleeder screw & slowly use a "C" clamp.

May 14, 2009 | 2002 Mazda 626

1 Answer

Pickup-mazda


The Mazda B-Series and Ford Ranger are essentially the same after 1994. Mazda motors are made by Mazda. The seating is lower but they slide back far enough by 6'2" brother has plenty of room.
Another neat fact is:
the B-series is "non-interference", meaning that breakage of its timing belt does not result in damage to valves or pistons, because the opening of the valves, the depth of the combustion chamber and (in some variants) the shaping of the piston crown allow sufficient clearance for the open valves in any possible piston position

Jan 20, 2009 | 2000 Mazda Pickup Troy Lee Cab Plus 4

1 Answer

Dome or Dish Pistons for Mazda FE3N 2L


The dome pistons will provide higher compression than the dished. the domed ones should have an eyebrow cut out for the valves. I believe you would be happiest going with the domes. you might run into spark knock with the increased compression

Nov 10, 2008 | 1993 Mazda 323

1 Answer

Can not figure out piston numbering on a 4 cylinder mazda mx6


For years 1990-1998 4cyl (most vehicles) :

looking at engine compartment from front of vehicle:

Piston Numbering is -- 1 2 3 4 -- from left to right.

Firing order is normally (unaltered) 1-3-4-2.

Brian

Jul 19, 2008 | Mazda MX-6 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...