Question about 2001 Lincoln LS

1 Answer

Firestone is telling me that i need a Right Control Arm and Steering Knuckle and that it is going to cost 1178.00. They also said that the bolt was loose on the ball joint i think. Can we just tighten this and get the car home?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

Have it towed to a different shop. More than likely you only need the bushings and joints which would cost significantly less.

Posted on Nov 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace left control arm on 99 mercury cougar


Here's what I found on Yahoo answers:
For the driver's side: yes, you will have to raise the motor.
On all models, remove the front motor mount, Mark the position of the right engine mount, remove 3 right engine to mount bolts. remove one right engine mount to body nut. On all models hold the strut shaft with an 8 mm allen wrench, loosen top retaining nut 5 turns. Raise vehicle, remove ball joint to steering knuckle pinch bolt. seperate control arm ball joints from steering knuckle. Do NOT damage ball joint seal. Remove pinch bolt attaching steering knuckle to strut. Slide steering knuckle up on strut, Move transaxle to gain access to control arm nuts and bolts. remove 2 nuts and bolts and attaching control arm to subframe. Lifting up control arm remove.
Now this to mark the motor mount because you are supposed to use a powertrain alignment guage when putting back together. if not you can bind the motor in the unibody and make for a shaky ride.
that drivers side lower control arm calls for 4.3 hours where as the passenger side calls for 1.3 hours. So you can see what your in for.
BTW these instructions are taken straight from the Ford repair manual.

Source(s):

http://mysite.verizon.net/t2bedlam/fr.jp...

Jan 02, 2013 | 1999 Mercury Cougar

1 Answer

Steering knuckle will not go back into control arm need help 2002 ford taurus


Ford engineers should be shot for this. You can buy the special tool shown below. Use it to lift the strut and knuckle up enough to get the ball joint on. Or, loosen the engine cradle bolts on that side and drop the cradle down enough to bet the ball joint stud into the control arm. Ford engineers should be shot for this bad design.

http://www.freedomracing.com/strut-removal-set-6584.html?gclid=Cj0KCQjwnazLBRDxARIsAECdausVMQQttQlO0jefdGrbgC_BE8Bv-a-UC5E0w1OSdkKdZaGolyAklK8aAqa-EALw_wcB

Jul 16, 2017 | 2002 Ford Taurus

1 Answer

Control arm replace


to replace control arm, you need place jackstands under the frame and lower vechicle so the weight of the vechicle rests on the jackstands and not on the control arms, then remove the front wheel remove ball joint and nut, remove steering knuckle from the lower ball joint using tool KM 507 B. remove control arm to crossmember nut and bolt, remove rear crossmember to body bolt and remove control arm.torque control arm to crossmember nut and bolt 81 ft lbs, torque ball joint to steering knuckle bolt nut 44 ft lbs.torque crossmember to body bolt to 145 ft lbs.

Feb 15, 2012 | 2001 Daewoo Nubira

1 Answer

How do i fix front right ball joint for 2001 mazda protege lx?


SAFELY RAISE SUPPORT FRONT OF VECHICLE ON JACK STAND MAKE SURE VECHICLE PARKED ON SOLID LEVEL GROUND. REMOVE WHEEL OR TIRE. REMOVE BALL JOINT STUD PINCH BOLT AND NUT FROM THE STEERING KNUCKLE.REMOVE BALL JOINT BY PRYING IT FROM THE KNUCKLE.REMOVE BALL JOINT TO LOWER CONTROL ARM BOLT AND NUT. INSTALL NEW BALL JOINT TO LOWER CONTROL ARM.TORQUE THE BOLT TO 86 FT LBS INSTALL BALL JOINT TO THE STEERING KNUCKLE TORQUE BOLT TO 43 FT LBS YOU MORE LIKELY NEED FRONT END REALIGNMENT AFTER THE JOB DONE.

Sep 09, 2011 | Mazda Protege Cars & Trucks

1 Answer

Front lower control arm replacement


To remove the lower control arm raise and support your car with jack stands.Next you want to remove the wheel that you are replacing the control arm on.Remove the ball joint nut and tie rod nut.Tap the steering knuckle to break the tie rod end loose from the knuckle DO NOT HIT THE TIE ROD SO HARD YOU DAMAGE THE THREADS.If you do you will also be changing a tie rod end.Tap on the steering knuckle until your ball joint stud comes loose.Remove the 2 bolts that mount the control arm to the frame.To install the new one just go in reverse.

Mar 09, 2011 | 2006 Ford Mustang

1 Answer

How to replace the passenger control arm on the 2006 suzuki grand vitara


Most front ends are set up basically the same way.First raise and support your front end and remove the tire.Both the upper and lower should look about the same.If you look at the control arm you will have an upper and lower ball joint and a tie rod end bolted to the steering knuckle.Remove the bolt on the tie rod end and use a ball joint separate to remove the tie rod end.Then remove the ball joint from the steering knuckle with your separator.Depending on which control arm it is if its the upper you will also have to remove the brake hose out of the way to remove the upper control arm.Once that's done you will see 2 bolts that hold the control arms to the frame remove these bolts and your control arm will come off,You might have to pry them a little bit to get them out.You also want to have something handy to block up your steering knuckle until your ready to put it back together.It wouldn't hurt to have a piece of wire just in case you need to tie something in place.And be sure you grease everything with a high pressure grease.

Mar 06, 2011 | 2006 Suzuki Grand Vitara

1 Answer

Need help changing balljoints


Found this article for you. Hope this helps

The ball joint is integrated into the lower control arm and cannot be replaced separately.
In many ways, that makes this project a lot less complicated (especially compared to the Taurus / Sable ;))

Before getting started, be sure to get an illustration of the front suspension - the linked Autozone Repair Guide is a good source.

Describing the scene & cast of parts:
  • The control arm connects to the frame with 1 large bolt/nut through a bushing on one end.

  • The other end has the ball joint stud sticking up that connects to the bottom end of the steering knuckle.

  • There's one more part involved: lower arm strut.
  • ** 1996-1998: This 'bar' connects to the middle of the control arm, and angles back and connects to the frame on the other.
    • 1999-2003: the end of the strut connects to the 'extension' coming off the control arm.

Removal Procedures:
Preliminaries: jack the car up, use a jack stand, chock the wheels, take the front wheel off - leave the key in the ignition so the steering wheel is unlocked.
  1. Remove the lower arm strut nut and dished washer from the end that goes through the middle of the control arm.

    NOTE: take notice of which way the dishing of the washer is pointing - you'll want to remember that for reassembly.

  2. Remove the 'pinch' bolt from the bottom of the steering knuckle that holds the ball joint stud in place - punch it all the way out of the knuckle.

  3. To make separating the control arm from the knuckle easier, you can use a small pry bar, or other handy tool to open up the 'pinch' point around the ball joint stud.

  4. I use a good length of 2x2 to leverage the control arm down - separating the ball joint stud from the knuckle.

  5. Last step - remove the control arm-to-frame bolt - and wiggle control arm off the end of the arm strut.

  6. Sit back and have a cup of coffee - 1/2 way there...

Installation:
  1. Put the end of the arm strut through the the control arm connecting point (middle for or control arm extension - model year dependent)

  2. Reattach control arm to frame - torque bolt to 85-97 ft lbs

  3. Ball joint stud to steering knuckle -

    * A second pair of hands really come in handy for this part
    * Line up the stud to the same angle as the opening in the bottom of the steering knuckle
    * I usually reach for the 2x2 to lever the control arm down far enough to get the stud lined-up and back into the steering knuckle

  4. Insert ball joint pinch bolt -

    NOTE: Don't start hammering the bolt back through the hole! There's a groove in the ball joint stud that must be lined up in the bolt hole - may have to tap the control arm up / down to get it "just right". Bolt slides in a whole lot easier then.
    Torque bolt to 46-52 ft lbs

  5. Reinstall strut washer & nut - this is where you were supposed to remember which way the washer 'dishing' was pointing!
    Torque to 85-97 ft lbs
Don't forget to put the wheel back on, and drop the van back to the ground.

Now is the time for the beer... Pricing Price references: Autozone, 1996-1998 $60, 1999-2003 $102

Aug 19, 2010 | 1999 Ford Windstar

1 Answer

How do you replace ball joints


Removing the Ball Joint Step 1 Loosen the lug nuts on the front wheel assembly with the ball joint you need to replace. Do not remove the lug nuts.
Step 2 Set the transmission in neutral (manual) or park (automatic) and raise the wheel off the ground using a floor jack. Then support the car on a jack stand.
Step 3 Chock the rear wheels and apply the parking brake.
Step 4 Remove the wheel lugs and the wheel assembly.
Step 5 Remove the mounting nut and dished washer that secure the stabilizer bar to the control arm. Use a wrench or ratchet and socket.
Step 6 Unscrew and remove the mounting bolt and nut holding the inner side of the control arm to the car's body. This will relieve the tension on the stabilizer bar. Use a wrench to hold the mounting bolt as you unscrew the nut with a wrench or ratchet and socket.
Step 7 Unscrew the bolt on the steering knuckle that holds the control-arm ball joint to the knuckle. Use a wrench or ratchet and socket.
Step 8 Spread the steering knuckle joint that holds the control-arm ball joint to the knuckle. Use a large screwdriver or pry bar. Then separate the ball joint from the steering knuckle.
Step 9 Pull the control arm from the stabilizer bar.
Step 10 Remove the stabilizer bar spacer from the control arm and keep it in a secure place. You will need to use it on the new control-arm ball joint assembly.
Installing the Ball Joint Step 1 Insert the new control-arm ball joint stud into the steering knuckle joint. As you look through the mounting bolt hole on the steering knuckle, align the notch on the ball joint stud with the hole. Insert a new ball joint mounting bolt and start a new nut on the bolt. Tighten the nut.
Step 2 Mount the stabilizer bar spacer in the control arm, then insert the stud bolt at the end of the stabilizer bar into the control arm mounting hole and spacer.
Step 3 Set the other end of the control arm in its mounting position and insert the mounting bolt. Then start the mounting nut on the bolt by hand.
Step 4 Hold the head of the mounting bolt that secures the control arm to the car's body using a wrench, then tighten the nut.
Step 5 Secure the stabilizer bar to the control arm with the dished washer and mounting nut. Tighten the nut.
Step 6 Install the wheel assembly and lugs. Tighten the lugs with the lug wrench just enough to hold the wheel assembly firmly in place.
Step 7 Lower the vehicle and finish tightening the wheel lugs.
Step 8
Remove the chocks from the rear wheels.

Aug 08, 2010 | 1998 Ford Escort

1 Answer

How to replace lower left front ball joint ?


Removal & Installation NOTE This procedure requires the use of the following special tools: J 9519-E Lower Ball Joint Remover and Installer, J 34874 Booster Seal Remover/Installer, J 41435 Ball Joint Installer, J 45105-1 Ball Joint Flaring Adapter and J 45105-2 Receiver.

  1. On 4WD vehicles, remove the wheel center cap and drive axle nut.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Tire and wheel
    • Wheel hub and bearing, if necessary
    • Outer tie rod retaining nut
    • Out tie rod from the steering knuckle using a suitable puller
    • Brake hose bracket retaining bolts and bracket
    • Upper control arm-to-steering knuckle pinch bolt and nut
    • Upper control arm from the steering knuckle
    • Lower ball joint retaining nut
    • Steering knuckle from the lower control arm using a suitable ball joint removal tool
    • Steering knuckle from the vehicle
    • Lower ball joint flange with a chisel
  4. Install tools J 9519-E and J 34874 to the lower ball joint, then use those tools to remove the lower ball joint from the lower control arm.
To install:
  1. Install or connect the following:
    • Lower ball joint to the lower control arm, using tools J 9519-E, J 41435 and J 45105-2
  2. Remove the tools from the lower control arm.
    • Tools J 9519-E and J 45105-1 to the lower ball joint
  3. Flare the lower ball joint flange with J 9519-E and J 45105-1, then remove the tools from the lower ball joint.
    • Steering knuckle to the lower control arm
    • Lower ball joint retaining nut and tighten to 81 ft. lbs. (110 Nm)
    • Upper control arm to the steering knuckle
    • Upper control arm pinch bolt and nut and tighten to 30 ft. lbs. (41 Nm)
    • Brake hose bracket to the steering knuckle
    • Brake hose bracket retaining nuts and tighten to 7 ft. lbs. (10 Nm)
    • Outer tie rod to the steering knuckle
    • Outer tie rod retaining nut and tighten to 33 ft. lbs. (45 Nm)
    • Wheel hub and bearing, if removed
    • Tire and wheel
  4. Lower the vehicle
    • Drive axle nut, if 4WD, and tighten to 103 ft. lbs. (140 Nm)
    • Wheel center cap, if removed
  5. Check the front wheel alignment.

Nov 30, 2009 | 2002 Oldsmobile Bravada

1 Answer

Need to replace the lower control Arm. Is there a procedure available?


Please be mindful to carefully note the position of the old parts as you disassemble the suspension, then follow these steps to do the re-installation:

REMOVAL

1. Disconnect the negative battery cable.

2. Raise and safely support the vehicle.

3. Remove the wheel and tire assembly.

4. Remove and discard the tension strut-to-control arm nut, then pull off the dished washer.

When separating the control arm from the steering knuckle, do not use a hammer. Be careful not to damage the ball joint boot seal.

5. Remove and discard the control arm-to-steering knuckle pinch bolt. Using a small prybar, spread the pinch joint slightly, then separate the control arm from the steering knuckle. A drift punch may be used to remove the bolt, but be very careful not to damage the ball joint boot seal.

Do not allow the halfshaft to move outward, or the tripod CV-joint internal parts could separate, causing failure of the joint.

6. Remove and discard the lower control arm inner pivot bolt and nut.

7. Remove the lower control arm from the frame and the tension strut.

INSTALLATION

Make sure the front washer is at the strut-to-lower control arm attachment.

8. Insert the strut into the inner bushing.

9. Position the lower control arm into the subframe bracket, using a new nut and bolt. Tighten to 73-97 ft. lbs. (98-132 Nm).

10. Assemble the lower control arm ball joint stud to the steering knuckle, making sure the ball stud groove is positioned properly. Be very careful not to damage the lower control arm seal.

11. Insert a new pinch bolt and nut, then tighten to 40-53 ft. lbs. (53-72 Nm).

12. Clean the strut threads to remove dirt and/or debris.

13. Install the dished washer, with its dished side away from the control arm bushing. Install a new nut on the strut and tighten to 73-97 ft. lbs. (98-132 Nm).

14. Install the wheel and tire assembly, tightening the lug nuts to 85-105 ft. lbs. (115-142 Nm), then carefully lower the vehicle.

I hope this helps.

Aug 17, 2009 | 1994 Ford Taurus

Not finding what you are looking for?
2001 Lincoln LS Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

fordexpert

Level 3 Expert

5467 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...