Question about 1998 Oldsmobile Cutlass

Open Question

What and how to fix code p1651 for a 1998 oldsmobile cutlass

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Thunder55
  • 318 Answers

SOURCE: i need a diagram of

There is usually a diagram sticker on the Fan shroud under the hood, check first

Posted on Jan 16, 2009

  • 1 Answer

SOURCE: 1998 Oldsmobile Cutlass Supreme Blower Motor

It's not to hard to do, just have to lay upside down in your pas. floorboard, remove plastic panels under gloove box with small nut drivers,(can't remember size) then there are three hex head screws holding on the blowerplus the wireing connector, anf it has a wierd rubber gasket, hope this helps.

Posted on Sep 12, 2008

  • 2 Answers

SOURCE: The windows in the 95 oldsmobile cutlass ciera won't work at all

maybe the wire is severed where the door (drver dr) pivots. thats what was wrong with mine. there is a rubber boot with crinkles in it that hold all the wires together. you can also try replacing the switch board that controls the wndws on the drvr dr. hope that helps.

Posted on Jan 20, 2009

Ajkill
  • 2035 Answers

SOURCE: Ignition switch

  1. If equipped, disable the SIR system as outlined in . Disconnect the negative battery cable.
  2. Remove the ignition switch trim ring (bezel) by gently prying it out from the lock cylinder with a small suitable prytool.
  3. Remove the trim plate by gently prying around the edges with a small suitable prytool.
  4. Remove the tilt lever (if equipped) by pulling it firmly out from the steering column
  5. Snap off the upper steering column cover by gently prying between it and the bottom cover.
  6. Remove the lower steering column cover screws and lower the steering column cover.
  7. If necessary, remove the instrument panel cluster trim plate.
  8. Remove the two ignition switch bolts.
  9. Detach the two electrical connectors.
  10. Disconnect the ignition lock cable from the ignition switch.
  11. Remove the ignition switch from the vehicle.
To install:
  1. Insert the key into the ignition switch cylinder and rotate it into the RUN position.
  2. Press the cylinder release plunger located at the four o'clock position on the ignition switch.
  3. Use the key in order to pull the cylinder from the ignition switch.
  4. Assemble the cylinder into the ignition switch.
  5. Verify the engagement and operation of the cylinder using the key.
  6. The remainder of installation is the reverse of the removal procedure.
  7. Good luck...

Posted on Feb 27, 2009

jeffbvegas1
  • 520 Answers

SOURCE: how to fix a code P1651 Quad Driver Module B Quick

This is very likely a failed PCM module and will need a replacement

Posted on Sep 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What makes the fuel pump not kick on on a 92 Oldsmobile Cutlass


There is a red wire close to the battery in the front. It's not connected to anything. Apply positive voltage and that will run your pump for testing purposes.

Dec 08, 2015 | Oldsmobile Cars & Trucks

1 Answer

Help with1995 Oldsmobile Cutlass Ciera SL Code reader scan tool


You need to buy an OBD1 Code Reader
1996 started OBD2 Systems

Jul 06, 2013 | 1995 Oldsmobile Cutlass Ciera

1 Answer

1993 olds Cutlass check engine code 26


I have the haynes repair manual from 1982-1996 oldsmobile cutlas ciera & Cutlas cruiser in the book it say the code 26 is the Quad Driver Module Circuit I hope this helps

Jan 15, 2012 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Need to fix a thermostat on a cutlass oldsmobile supreme


Here http://www.buyautoparts.com/thermostat.htm you can find thermostat to fix on your oldsmobile. Hope this solves your problem.

Aug 09, 2011 | 1997 Oldsmobile Cutlass Supreme

1 Answer

How to unlocking car radio oldsmobile 1997 cutlass supreme


we don't have any access to the codes here, they are secure and unique to each car and radio, go to link for codes, it does cost, but very cheap.

http://www.delcolockcodes.com/

Oct 23, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

The windows in the 95 oldsmobile cutlass ciera won't work at all


maybe the wire is severed where the door (drver dr) pivots. thats what was wrong with mine. there is a rubber boot with crinkles in it that hold all the wires together. you can also try replacing the switch board that controls the wndws on the drvr dr. hope that helps.

Oct 04, 2008 | 1995 Oldsmobile Cutlass Ciera

1 Answer

1994 cutlass supreme--security light on--car won't start


take to dealer and have them reprogram the computer

Jun 23, 2008 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1998 Oldsmobile Cutlass Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...