Question about 1988 Mazda B2600 Cab Plus

1 Answer

How do i remove timing cover off 89 mazda b2600 2.6 seems to be hangin up at the bottom drivers side

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Put a rope to the car and toll it to the nearest scarp yard and burn the mazda

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove timing cover on Mercury Cougar (8-1995) ?


Under neath the car...where of course you can't see thanks to dumbbb design that is anti back yard mechanics..

.Remove the four front oil pan-to-timing cover retaining bolts. These four bolts go into both the oil pan and the timing cover.

For some visual guide yo can go to autozone repair guide and look at a crown vic 4.6L engine,with about same as yours, and see some help there hopefully. Good luck

Feb 25, 2015 | 1995 Mercury Cougar

1 Answer

How do I replace the valve cover gasket on a 2002 Saturn L200, 2.2 engine?


Disconnect the camshaft cover grounding strap.Right side of engine.
Remove ignition module, 4 bolts , and disconnect the electrical connection to it. Pull straight up to remove.
Remove 4 spark plugs.
Remove the coolant pipe bracket.
Remove the fuel line bracket.
Remove the 12 bolts holding down the cover, then pry up around the edges GENTLY to remove. You might want to use a rubber mallet at this stage, just don't overdo hitting it, its cast aluminum..
The gasket around the edge and around the spark plug holes don't need sealant, the new design does away with this.
Now would be a good time to check the wear on the Teflon timing chain shield between the camshaft sprockets.
Installation is in reverse order.
Camshaft cover bolts : Tighten to 89 INCH pounds.
Camshaft Ground Strap Bolt : 89 INCH pounds.
Spark Plugs : 15 FOOT pounds.
Ignition coil to camshaft cover bolts : 71 INCH pounds.
Coolant pipe AND Fuel line bracket bolts: 89 INCH pounds.
Good luck.

Feb 21, 2015 | 2002 Saturn L-Series

1 Answer

I have 89 mazda b2600i no spark @coil what should I be testing?


ignition control module.. i think its on the driver side under the hood by the coil small and square ish shaped

Feb 03, 2011 | Mazda B2600 Cars & Trucks

1 Answer

How do you remove the back seat on a 1998 Mazda Protege with standard rear seats?


push HARD on the bottom of the bottom seat at the lower front point by the floor (one side at a time) and lift-once you release both sides, it just pulls out.

Dec 24, 2010 | 2002 Mazda Protege

1 Answer

How do i replace the starter of a 1987 mazda rx7


The starter is mounted on the driver's side bottom of the engine.
  1. Disconnect the negative battery cable.
  2. Raise the vehicle and support it safely with jackstands.

5e542b9.gif
Starter mounting-1986-89 RX-7

  1. Disconnect the heavy battery cable from the terminal marked B on the starter solenoid (or magnetic switch on later models).
  2. Disconnect the thinner ignition switch wire from the terminal marked S on the solenoid/magnetic switch.
  3. On vehicles with automatic transmissions, remove the front starter motor bracket bolts and the bracket. Remove the two starter attaching bolts and remove the starter.
To install:
  1. Support the starter by and hand and position it onto the flywheel housing. Install the two mounting bolts. On 1986-89 RX-7s, torque the bolts to 24-33 ft. lbs. (33-45 Nm). Install the front starter bracket, if removed.
  2. Connect the starter wiring to the appropriate solenoid or switch terminals. On 1986-89 models, torque the B terminal (battery cable) nut to 8 ft. lbs. (11 Nm).
  3. Lower the vehicle.
  4. Connect the negative battery cable.

Mar 06, 2010 | 1987 Mazda RX-7

1 Answer

Where is the timing belt cover on a '96 Mazda?


Under hood, driver side, upper engine area, mounted in distributor

Sep 11, 2009 | 1996 Mazda Protege

1 Answer

Breakfluid leaking from bottom of resivior and seat belt question


Yea there should be a gasket/O-ring. Problem is the only place to get just that part is probable the dealer.

Mar 31, 2009 | 1989 Mazda 323

3 Answers

My 89 mazda 323 turns over but wont start


Last week my 323 89' Mazda stop working as I was driving it in middle of the street, I pushed to the side. it would not start, the starter sounded ok, but the car just didnt start, I checked the fuses, gas pump, and all seemed to be ok, finally with the help of a friend we found out that the ignition rotor at the distributor wasnt working we then replace it with a new one from autozone , is about 5 dollars, now it works just fine, big problem easy solution.

Victor

Dec 01, 2008 | 1989 Mazda 323

2 Answers

Mazda astina water pump


It most likely runs off the timing belt. check there behind the timing belt cover.

Nov 25, 2008 | 1994 Mazda 323

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...