Question about 1993 Nissan Quest

1 Answer

1993 Nissan Quest GXE-Power seat belt retractors both create a slipping, rattling noise. The drivers side seatbelt is stuck in one position (driving position). I've tried lubricating it to no avail. Is this a recall item, if it is how much of a hassle will it be to get the dealer to repair?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I had this same problem with mine, what i did was take off that part of the interior to where you can get to the actual motor itself and disconnect the power to it.. i found out that for some reason the track to mine was completely eaten through when mine did what yours did.. just make sure its in the driving position all the way so it's safe to use while driving and it wont move. the only drawback to this is the seatbelt light stays on the dash..

Posted on Nov 21, 2010

  • cody_08_2002 Nov 21, 2010

    nevermind that. after more research i found out that all seatbelts in nissan vehicles from 1989 and up are warrantied for life. im referring to this:http://forums.nicoclub.com/broken-seat-b...
    i'd check on that. :)

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can u stop the buzzing noise for the automatic seatbelt on 93 nissan quest? Is there a fuse?


No fuse, but on the side between the door the panel you can take off and just unhook the wire(s) and then put the panel bak on. The only problem is that the light will stay lit on your drivers dash board. But it ststop the noise with no effect, Take 20 minutes top to do this.

Jul 10, 2012 | 1993 Nissan Quest

1 Answer

I have a 2010 Ford Fusion. The seats belts are so tight that I can't stand to wear them. Especially the one on the drivers side. It is like with every little jar it tightens up. I have to hold it...


hello from Fordland!
your dealer is able o supply you with a seatbelt extender at no charge. this is a courtesy that ford gives to thei owners. see your local ford dealer for details..i hope this helps, your thumbs up is appreciated....BTW, the right front and all rear seat belts have a child safety feature buil into the retractors. it will cause the seatbelts to cinch tight an not release once engaged, until the seatbelt has been fully retracted therby releasing the locking mechanism...this feature is only engaged when the retractor is pulled out to is fullest limits, at that point you will hear a ratcheting noise as it retracts....

May 24, 2011 | 2006 Ford Fusion

2 Answers

How can I un-stick a stuck seat belt. It worked fine last time we used it and does not seem to be twisted. 2001 chevy blazer


If it is stuck in the seat belt clip (meaning its buckled) then that model year had a seat belt buckle recall for failure. If its stuck in the seatbelt retractor and your seatbelt retractor is floor mounted there is a release pin on the ratchet gear. TO access it you will need to remove the plastic cover located at the floorboard next to the door on the side of the car that is stuck. If its a seat mounted retractor this means the retractor mechanism is located within the seat frame. You will need to view the bottom of the seat of the belt and see the anchor point. Seatbelts must be anchored to frame of car. Trace it into the seat back. If its located in the back of the seat you will need to remove the seat cover to the extent to reach the mechanism. This can be located at the bottom of the seat.. but more than likely is located at the shoulder area. The Seat cover (fabric) is removeable via clips located at the base and tucked into the seat (think hidden bra/pant clip style connectors or zipper) If you have leather seats it is a bit more detailed and more difficult to manage the seat covers. Typically your local Chevrolet dealer mechanic can get this done in 10 minutes (based one experience) and quite possibly wont charge you or charge you minimally. The downside to this is if its locked that means the same gear that locks it in an accident was frozen in place somehow and this typically indicates a dirty dirty spring or broken spring mechanism. The locking pin operates on centrifugal force and activates based on speed by which the seat belt is pulled out. (just a bit of knowledge) Good luck

Jun 15, 2010 | Cars & Trucks

1 Answer

Rear passengerside seat belt stuck in retracted position,cannot raise rear seat to upright position. how do I fix it?


You will most likely need to replace the seatbelt retractor. The best place to find a replacement is usually your local self service auto salvage lot. I replaced mine last year and it ran me $10 for the retractor and u pull and pay.

Mar 24, 2010 | 2001 Volvo V70

1 Answer

Passenger seatbelt adjuster rattle.


Are you sure its the b pillar? When driving its really hard to hear noise's. This car is noise prone by the way.

A very common noise comes from the 3rd row lower seat brackets. Drive the car and check for noises from the 3rd row seat bottom.

May 19, 2009 | 2004 Nissan Quest

1 Answer

Saturn vue 2007, rear folding seat will not return to proper position due to seat belt being locked up.


They have a problem with the seatbelt retractor getting jammed up causing the belt to jam & not let the rear seat fold back up.The easiest way to get the seat back up is to cut the seatbelt & fold up the seat.Then the rear seat needs to be disassembled to gain access to the seatbelt retractor assy which has the seat belt made on.Hopefully it's still under warranty or Ext. warranty.hope this helps

May 17, 2009 | 2007 Saturn VUE FWD 4

1 Answer

1993 QUEST GXE SEATBELT Automatic driver side seatbelt not working.


they have a module in the center dash area adn there is a limit switch at each end of belt travel. Kind of like garage door opener.

check fuses & relays first.

go here for Quest help

http://groups.yahoo.com/group/villagerquest/

Mar 02, 2009 | 1993 Nissan Quest

1 Answer

Seat Belt repair/replace


  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Nov 03, 2008 | 2000 Nissan Maxima

Not finding what you are looking for?
1993 Nissan Quest Logo

513 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...