Question about 2000 Nissan Altima

1 Answer

Do the outside mirrors clip into the electric motor? I lost just the mirror part (glass & frame) the rest is in perfect condition as far as I can see. Can just the mirror be purchased? or do I have to buy the entire assembly?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,672 Answers

You could buy the mirror part! Order it in ur nearest Nissan Parts dealer!

Posted on Nov 09, 2010

Testimonial: "thank you, very good advice"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have malfunctioning electric-driven exterior towing mirrors on a 1999 ford f-350. How to diagnose/fix? Mirrors respond only to right adjust; no response on up/down or left adjust.


there is a separate motor for up/down and another for left/right adjust. The glass is serviceable but not the motors, built into the frame of the mirror body.

SECTION 501-09: Rear View Mirrors 2000 F-Super Duty/Excursion/Motorhome Chassis Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Left-hand dual arm mirror with heat shown, non-heated and aero mirrors similar.
  1. Position the exterior rear view mirror glass in the full down position.
  1. Grasp the top and carefully pull the mirror glass away from the mirror housing.
  1. Disconnect the electrical terminals (if equipped) and remove the exterior rear view mirror glass.
Installation
  1. Remove the jack pins from the mirror glass back.
  1. Remove the sealing boots.
  1. Install the jack pins in the sealing boots.
  1. Install the jack pins and sealing boots.
    1. Install the jack pins in the mirror housing.
    1. Install the sealing boots so the boot shoulder is under the mirror collar.
  1. Loosely install the glass.
    1. Connect the electrical wiring to the electrical terminals (if equipped).
    1. Position the friction pins in the mirror housing.
    1. Align the jack pin locating tabs to match with the mirror glass back.
  1. Using a flat hand, press on the center of the mirror glass until seated on the center pivot of the mirror housing.
    • Press the mirror glass toward one of the jack pins until snapped in place.
    • Repeat for second jack pin.

Jan 13, 2011 | Ford F-350 Cars & Trucks

1 Answer

How to replace side mirror


Outside Mirrors REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. NOTE: This procedure is for power mirrors. The procedure for a manual mirror is the same with the exception of the lack of electrical wiring.
  2. Remove the door trim panel, plastic fasteners from the sound insulator and water deflector, as required.
  3. Unfasten the retainer, then remove the mirror trim panel. Fig. 1: The outside mirror has a trim panel which is secured with a screw and a retaining clip 89630g19.jpg
    Fig. 2: Unfasten the retaining screw . . . 89630p19.jpg Fig. 3: . . . then remove the mirror finish panel. Note the panel retaining clip (see arrow) 89630p10.jpg
  4. Disconnect the wiring connector and remove the wiring from the door retaining tabs. Fig. 4: Exploded view of the outside mirror cable routing 89630g20.gif

  5. Remove the mirror retaining nuts/screws, then remove the mirror with insulator and wiring. Fig. 5: Pull the sound absorber filler pad out of the door 89630p11.jpg Fig. 6: Unfasten the side view mirror retaining nuts and bolts 89630p12.jpg Fig. 7: Exploded view of the outside mirror assembly mounting 89630g18.jpg
    To install:
  6. Refit the mirror with insulator and wiring into position.
  7. Install the mirror retaining nuts/screws.
  8. Route the wiring through the door retaining tabs and reconnect the electrical connector. Make certain the wiring harness does not interfere with the window glass operation.
  9. Install the water deflector, sound insulator and door trim panel, as required.
  10. Connect the negative battery cable. prev.gif next.gif

Nov 05, 2010 | 1997 Pontiac Bonneville

1 Answer

How to replace a broken wing mirror on a Volvo S40 1980 model



Power Dr Mirrors Diagnosis & Testing


Removal & Installation
Motor
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Disconnect the negative battery cable. The mirror inside cover trim The door panel The electrical connector to mirror motor The nut attaching mirror assembly to door frame The outside rear view mirror

    0900c152801c11d4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing cover trim and nut
    Removing cover trim and nut

    0900c152801c11d5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing mirrored glass from assembly
    Removing mirrored glass from assembly

  3. Remove the mirror glass:
    1. Fold the mirror glass forwards and inwards as illustrated.
    2. Grasp and pull the mirror glass lengthways until it releases.
    3. Work the glass out.

  4. Remove electric motor:
    1. Remove the 3 screws from behind the mirrored glass.
    2. Separate the connectors
      NOTE Remember the positions of the connectors.
    3. Remove the mirror motor.

      0900c152801c11d6.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Removing connectors and screws holding mirror motor
      Removing connectors and screws holding mirror motor



To install:
  1. Install or connect the following:

    The electric motor The electrical connections The 3 screws that go behind the mirror Install the terminal pins Fold out the mirror mounting on the motor Hook the mirror glass into the inner mounting Press the mirror glass into place. Place mirror in position in door

    0900c152801c11d7.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Reattaching mirror and electric motor connectors
    Reattaching mirror and electric motor connectors

  2. Install or connect the following:

    The nut attaching mirror assembly to door frame The connector The door panel The mirror inside cover trim The negative battery cable

Oct 23, 2010 | 2000 Volvo S40

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

How do you install turn signal lens on side mirrors on a 2005 F250?


- Adjust the mirror so the mirror glass is in as far as it will go (meaning if you were looking in the mirror you would see the side of the truck)

- Look inside the mirror housing
- Locate silver clip
- Using a flat screw driver, push the clip in
- Lenses will pop out on the outside
- Remove bulb
- Replace bulb
- Snap back together when new bulb in place.

May 02, 2010 | 2008 Ford F-250 Super Duty

1 Answer

How to change mirror turn signal light, 2009 f250


- Adjust the mirror so the mirror glass is in as far as it will go (meaning if you were looking in the mirror you would see the side of the truck)

- Look inside the mirror housing
- Locate silver clip
- Using a flat screw driver, push the clip in
- Lenses will pop out on the outside
- Remove bulb
- Replace bulb
- Snap back together when new bulb in place.

Mar 27, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

1990 cutlass ceira how do you replace drivers door side mirror


Outside Mirrors REMOVAL & INSTALLATION Standard
  1. Remove the door trim panel and detach the inner panel water deflector. With the glass in the down position, pull out the front portion of the glass run weatherstrip. Fig. 1: Unfasten the attaching nuts from the mirror base studs, then remove the mirror 8c45877.gif


  1. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler, then rotate retainer rearward.
  2. Remove the noise control patch to gain access to the screw at the belt, then remove the screw.
  3. Remove the filler attaching screws at the top front of the window frame, then remove the mirror and filler from the door.
  4. Remove the attaching nuts from the mirror base studs, then remove the mirror. To install:
  5. Be sure that the mirror gasket is aligned.
  6. Replace the mirror and filler on the door. Install the filler attaching screws at the top front of the window frame. Attach the nuts to the mirror studs and tighten.
  7. Install the screw at the belt, then insert the noise control patch.
  8. Insert the retainer, then install the attaching bolts and screws to the front glass run channel lower retainer to filler.
  9. Replace the front portion of the glass run weatherstrip, insert the inner panel water deflector, then reinstall the door trim panel.
Manual Remote
  1. Remove the mirror remote control escutcheons and door trim panel. Detach the inner panel water deflector. NOTE: Right side remote mirror may require detaching part of the instrument panel.
  2. With the glass in the down position, pull out the front portion of the glass run weatherstrip.
  3. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler and rotate retainer rearward.
  4. Remove the noise control patch to gain access to the 0.3 in. (7mm) screw at the belt and remove the screw.
  5. Remove the filler attaching screws at the top front of the window frame.
  6. Remove the mirror base with mirror and cable assembly from the door.
  7. Remove the mirror to filler attaching nuts and remove the mirror and cable from filler. To install:
  8. Be sure cable is routed around front glass run channel retainer and installed to clip.
  9. Install and connect the cable to the filler.
  10. Attach the filler nuts to the mirror, then tighten to 72 inch lbs. (8 Nm).
  11. Install the mirror base with the mirror and cable assembly to the door.
  12. Insert the filler attaching screws to the top of the window frame, then install the screw to the belt.
  13. Secure the noise control patch.
  14. Attach the bolts and screws to the front of the glass run channel lower retainer and filler.
  15. Install the glass run weatherstrip.
  16. Attach the inner panel water deflector, door trim panel and mirror remote control escutcheon.
Electric Remote
  1. Disconnect the negative battery cable.
  2. Remove the mirror remote control escutcheons and door trim panel. Detach the inner panel water deflector and the electrical connector for the mirror. NOTE: Right side remote mirror may require detaching part of the instrument panel.
  3. With the glass in the down position, pull out the front portion of the glass run weatherstrip.
  4. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler and rotate retainer rearward.
  5. Remove the noise control patch to gain access to the 0.3 in. (7mm) screw at the belt and remove the screw.
  6. Remove the filler attaching screws at the top front of the window frame.
  7. Remove the mirror base with mirror and electric connector from the door.
  8. Remove the mirror to filler attaching nuts and remove the mirror and electric wire from filler.
  9. To install, reverse Steps 1 through 6. Be sure electric wire is routed around front glass run channel retainer and installed to the clip. Tighten the nuts to 72 inch lbs. (8 Nm).
  10. Connect the negative battery cable, then reset the clock, radio and any other accessories if required.

Aug 25, 2009 | 1990 Oldsmobile Cutlass Ciera

1 Answer

99 explorer drivers side mirror vibrates


are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

  1. Remove the front door trim panel; refer to Section 501-05 .
  2. go to car-part.com for a used mirror. Page with * is cheapest seller.
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the speaker.
  1. Remove the outside rear view mirror (17682).
    1. Disconnect the power mirror wiring clips.
    1. Remove the outside rear view mirror nuts.
    1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).
------------------------------------------------------
f9d70e9.gif
----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.
4d9527f.gif

Apr 12, 2009 | 1999 Ford Explorer

1 Answer

Eddie Bauer mirror replacements


is it an aero mirror with no arms?
Or a trailer tow mirror with arms?
The glass is repalceable. It is mounted on a center post with a ball on it. The mirror has a socket on the back center.
It also has 2 jack srews (plastic) that go into the tiny motors that move the mirror. You can push and pull on the glass and they will retchet, it won't hurt them.

You have to pop the mirror off the ball.

It helps to heat the socket with a hair dryer to put the new one on.
Please rate as fixya if this solves your problem.

Glass — Outside Rear View Mirror
Removal
  1. Remove the mirror glass.
    1. Position the mirror glass to obtain a gap at the outside edge of the mirror.
    1. Carefully pry the outside edge of the glass away from the mirror housing.
d6ec385.gif Disconnect the electrical connector

987d3c2.gif
Connect the electrical connector


NOTE: Engage the center pivot before the four inserts.
Install the mirror glass.
  • Engage the center pivot and the four inserts
52f3cfa.gif

Mar 10, 2009 | 1997 Ford Expedition

Not finding what you are looking for?
2000 Nissan Altima Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...