Question about Mercedes-Benz B-Class

Open Question

How to locate the injection timing mark on mb100 engine? Please show picture diagram. thank you.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: 1999 kia sportage timing marks

dfd3ea1.gif Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif

  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
  8. NOTE: Replace tensioner spring if timing belt deflection is excessive.
Timing Belt Installation


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Posted on Jul 26, 2009

skdeepak88
  • 232 Answers

SOURCE: desparetly need diagram for 1990 volkswagen golf 1.8 timing marks

http://images.eurotuner.com/images/eurp_0801_07_z+2001_vw_golf_1-8t+1-8_liter_20v_engine_atp_gt28rs_turbo_vf_engineering_engine_mount_usrt_genesis_415cc_injectors.jpg please rate me!!

Posted on Aug 16, 2009

  • 58 Answers

SOURCE: geo metro timing diagram

woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck

Posted on Jan 29, 2009

  • 50 Answers

SOURCE: timing marks on 2002 2.4 litre engine

They'll usually be offset just a hair, and I mean a hair. If it's a tooth off, it's wrong. Make sure the mark on the oil pump is lined up with the MARK on the gear, not the tooth. I think the mark is actually lined up with the trailing edge of the tooth.
808ab228.gif

Posted on Apr 15, 2009

  • 6982 Answers

SOURCE: timing chain mark diagram for a 94 grand am????

Haynes lists the entire procedure for setting the position of the cams etc. Positioning of these is critical...If off by even a slight amount the valves WILL strike the pistons and destroy the engine. DO NOT use any parts made by SA Gear...They have no quality control and will deny any claim made against them. Make sure that the chain guides are in good condition and that the chain tensioner is operating properly.

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A Isuzu NPR 4hf1 rotary pump timing marks set


Hi. If it has a rotary pump, the pump needs to be installed with the crank at 49 deg BTDC on the compression stroke cyl 1. Mark dot gear on pump with white paint. Line up dot gear on pump with line on pump bracket and install. Remove PRM sensor from bell housing and check if line on pump gear is still lined up with line on pump bracket.

Feb 05, 2015 | Isuzu Cars & Trucks

1 Answer

Is there a ford focus timing marks single overhead cam diagram


depending on trans and engine mount type the mark my be on flywheel but generally most cars it is located on the belt pulley attached to crank rod, center bottom one on engine block. the timeing mark should be visable from top looking down. if you use a big ratchet to turn over the engine by hand and go slowly, you should see thhe marks pass as you do so.

Aug 14, 2014 | 2002 Ford SVT Focus

2 Answers

How do i find the number one wire loctaion on the distributor of a 2001 honda accord ex. 2.3l v-tech


Here is the diagram showing the number one cylinder location.
If you want to know when #1 is ready to fire remove the spark plug and rotate the engine by hand until you fell pressure in the cylinder with your finger over the hole, then look at the timing mark on the front pulley, move the engine until the mark is at "0" TDC, then remove the distributor and set it down so the rotor points towards the location of # 1 in the diagram below.
emissionwiz_124.gif

Oct 13, 2011 | 2001 Honda Accord

1 Answer

I need to know where the timing marks are on a 96 4wd isuzu rodeo. CAN ANYBODY HELP ME PLEASE?



  • I hope you get this, I was going to go to bed until I noticed how bad you were needing some timing marks :)

  • Injection pump and camshaft alignment marks-diesel engine
ironfist109_302.jpg

ironfist109_303.jpg

  • Tensioner pulley bolt sequence (diesel)


ironfist109_304.jpg


  • Crankshaft sprocket timing mark-2.3L and 2.6L engine
ironfist109_305.jpg

  • Camshaft sprocket timing mark-2.3L and 2.6L engine
ironfist109_306.jpg
  • Timing belt installation sequence-2.3L and 2.6L engines
ironfist109_307.jpg
  • Timing belt tensioner lockbolt-2.3L and 2.6L engines
ironfist109_308.jpg

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 06, 2011 | 1996 Isuzu Rodeo

1 Answer

Need timing belt marks for 1999 kia sportage diagram


  • Hi, I can help. Please see the diagrams below for your timing marks.

  • The picture below is the crankshaft marks that need to be lined up before you remove the timing belt.
ironfist109_30.png
  • Below is the intake and exhaust camshaft pulley marks.

ironfist109_31.png


  • Below is an exploded diagram of the engine components in relation to the timing belt.

ironfist109_32.png
  • Please not that this diagram is good for both 4X4 and 2X4 2.0 Engine (which is the only engine Kia Sportage had that year).

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Aug 27, 2011 | Kia Sportage Cars & Trucks

1 Answer

Hi ive got a 1996 isuzu bighorn ive attempted to change the timing belt but the injector pump pulley moved when i took the belt off. i put it back where i thort it was and tried a tooth either way but no...


Timing belt installation

1. Ensure locking bolts located correctly [4] & [5] in the picture below:

tdisline_32.jpg
CS = Crankshaft
CA = Camshaft
IP = Injection Pump

2. Ensure timing marks aligned [10].
3. Fit timing belt in clockwise direction, starting at crankshaft sprocket.

NOTE: "ISUZU" lettering on belt should be readable from front of engine.

4. Slacken tensioner pulley bolt [9]. Push tensioner pulley against belt.
5. Ensure belt is taut between injection pump sprocket and tensioner pulley as well as crankshaft sprocket and camshaft sprocket.
6. Position tensioner lever [8] against tensioner pulley housing.
7. Remove locking bolts from sprockets [4] & [5].
8. Apply a load of 10 ... 12 kg to tensioner lever. Use spring balance [11].
9. Tighten tensioner pulley bolt to 80 Nm.
10. Turn crankshaft slowly 45 degrees anti-clockwise. Use spring balance to tension belt.
11. Repeat tensioning procedure at 45 degrees intervals for one anti-clockwise turn of the crankshaft.

NOTE: DO NOT turn crankshaft clockwise during tensioning procedure!

12. Fit tensioner lever to original position. Tighten nuts [12].
13. Install: Injection Pump flange [6], Camshaft sprocket flange [7], and water pump pulley.
14. Install components in reverse order of removal & refill coolant.

tdisline_33.jpg
PLEASE DO RATE MY RESPONSE. THANKS!

Nov 27, 2010 | 1996 Isuzu Trooper

1 Answer

Need a copy of the timing marks for a 1.8 liter turbo for 1999 and engine diagram


1.8 engine but which engine ,is it a petrol or a diesel ,direct injection or indirect injection ,has the timing belt broke did you mark it up with some white paint??

Jun 25, 2010 | Cars & Trucks

2 Answers

Diagram of markings on timing belt


I repaired a 3.1 4JG2 but the mechanic doesn´t know how to set the injection time. I can see the marks on the crank and camshaft as well as the inyection pulley but if I try to install the belt "just like that", the injection goes wrong with explosions and white smoke. Can anyone help please? Is there any other procedure to follow to time the inyection?
thanks in advance

Jun 30, 2010 | 1996 Isuzu Trooper

1 Answer

I need the timing marks to set the crankshaft to top dead center for a timing belt replacement. I just need a diagram to show me where the timing marks are located, where should the camshaft pulley mark be...


1986 Dodge Truck RAM 50 4WD 2.6L 2BL 4cyl

Fig. Timing belt and components-2.0L engine
9f07c9a.jpg


Fig. Location and correct alignment of timing marks for the timing belt (camshaft)
6f4c9d6.jpg


Fig. Timing marks-2.3L diesel engine
40625e5.jpg


Fig. Timing marks-2.4L engine
124bdbc.jpg


More details, autozone.com (free register). Good luck.

Sep 29, 2009 | 1986 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

760 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...