Question about 1996 BMW 318

1 Answer

1992 BMW Cylinder head

Hi I'm looking for cylinder head torque settings for 316/318 BMW 1992 E36.
I've just removed the head to repair a valve seater. so i need to put it back

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

30nm 90 degrees, 90 degrees Renew bolts!!

Posted on Jun 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque settings for polo bah motor big ends :mains and cylinder head


CHECK BELOW..
25458898-ms2db0pp00uj21y1nio4xcxs-1-0.png

Tightening torques
Bolted connections Tightening torque
Bolts, nuts M 6 10 Nm
M 8 20 Nm
M 10 45 Nm
M 12 60 Nm
Deviating from above
Exhaust pipe to manifold 40 Nm
Installation
Note
t Only remove the new cylinder head gasket from its packing immediately before installing.
t Handle the new gasket with extreme care. Damaging will lead to leaks.
- Place a clean cloth in cylinders so that no dirt or emery cloth particles can get in between cylinder wall and piston.
- Also prevent dirt and emery cloth particles from getting into the coolant.
- Carefully clean cylinder head and cylinder block sealing surfaces. Thereby ensuring that no scoring or scratches are formed (when using abrasive paper the grade must not be less than 100).
- Carefully remove metal particles, emery remains and cloths.
- Set No. 1 cylinder piston to TDC and then turn crankshaft back slightly.
- To centralize, screw guide pins from 3450/1 into front outer holes for cylinder head bolts-flechas-.
- Place the new cylinder head gasket in the centralizing pins -A-. Lettering (Part No.) must be readable.
- Fit cylinder head, screw in 8 remaining cylinder head bolts and tighten by hand.
- Remove the guide pins with tool 3450 by the bolt holes. To do this, turn the tool left until the pins are removed.
- Fit remaining cylinder head bolts and tighten hand-tight.
- Tighten cylinder head in tightening sequence as follows:
- Tighten all bolts to 30 Nm.
- Then tighten all bolts a 1//4 turn (90 °) further using a rigid wrench.
- Then tighten all bolts again a 1/4 turn (90 °) further.
Note
There is no requirement to retighten the cylinder head bolts after repairs.
The rest of the assembly is basically a reverse of the dismantling sequence.
Note
When the camshaft is turned, the crankshaft must not be at TDC. Danger of damage to valves or piston crowns.
Installing toothed belt and adjusting valve timing > Chapter.
Filling with new coolant > Chapter.
- Interrogate fault memory > Chapter.

Feb 21, 2015 | 2006 Volkswagen Polo 1.6

3 Answers

How do you replace the head gasket


with great difficultry, It is verry time consuming end verry costly to have it (Replaced)

Nov 27, 2012 | 2000 Kia Sportage

1 Answer

Cylinder head torque settings bmw 318i m43


Hi dear40,

The m43 engine should be similar to both the m42 and m44. The cylinder head torque settings are 22ft/lb and 90degree torque angle, and another 90 degree torque angle. Make sure to wait approximately 10minutes before performing the 2nd torque angle.

Jun 11, 2011 | 1997 BMW 318

2 Answers

How much lb ft. of torque should i put on the cylinder head bolts of a 1992 toyota hilux surf turbo diesel 2lt engine.


what is the valve clearance and cylinder head torque for toyota 2lt diesel engine

kasim

Jan 25, 2010 | 1992 Toyota 4Runner

1 Answer

Is it possible for a BMW E36 316i to bend valves when my cambelt hads stripped?


Yes its very possible possible that valve damage may have occured when the belt failed.I would suggest that you reinstall a new belt and attempt to crank the engine.Theres a chance it that it did not bend any valves.If it does not crank then cylinder head will have to be removed for the repair.

Jan 03, 2010 | 1996 BMW 318

2 Answers

I need head bolt specs for a 1992 bmw 325 i


I presume you want torque setting. If so here is

BMW 6 cylinder engine
According to my manual as follows:

cyl head to engine block
stage 1 30nm(22ft-lb)
stage 2 + 90 degrees
stage 3 + 90 degrees

cyl head to lower timing chain cover 10nm (89in - lb)

Loosening sequence is from oustside to inside crossover and tightning from inside to outside.

Jun 16, 2009 | 1992 BMW 3 Series

1 Answer

1992 bmw ignition lock assembly replacement


BMW ignition lock replacing.

According to manual no special tools needed. here procedure!

  1. Ignition elec switch. Disconnect battery. 2. remove trimpanel from lower leftside of instrument panel. remove screw retaining lower steering column and remove cove. 3. remove slotted screws on both side of switch. 4. relase tabs and remove switch from elec harnass and remove sealer.. note: before mating new ignition elec switch check that switch is in correct position. seal screws again.
  2. Ignition lock cylinder replacing. 1. insert master key and turn 60 deg to radio position. 2. inset piece of stiff wire into opening in lock cylinder and pull cylinder out. (Note early models up to 10/95 turn lock cylinder back 12 deg to release)

Jun 13, 2009 | 1992 BMW 3 Series

1 Answer

Head bolt touqe settings


Tightening torques

Do not reuse the bolts as they may be stretched.

Cylinder head to engine block
Stage 1: 32Ft-lbs
Stage 2: +90degrees
Stage 3: +90degrees

Cylinder head to lower timing
chain cover: 89in-lbs

Nov 27, 2008 | 1992 BMW 3 Series

3 Answers

Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Jun 16, 2008 | 1992 BMW 3 Series

Not finding what you are looking for?
1996 BMW 318 Logo

406 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...