Question about 2004 Toyota RAV4

1 Answer

2004 toyota rav4 rear bumper assembly guide

I need to know how to remove the drivers side corner rear bumper assembly to repair a dent my daughter put into it, I need a few tips as to how / where are the bolts

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

There are two bolts to the center and two around the corner on at the edge up high and one at the bottom of the bumper/ Please rate my response thank you very much

Posted on Feb 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove bumper


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly.

2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle.
3. Install rear bumper in reverse order of removal.

Dec 22, 2013 | 2004 Kia Sedona

1 Answer

Rear bumper removel


No need to remove it just fill the dent and repaint it.

Aug 20, 2012 | 2004 Ford Freestar

1 Answer

Need part name or description


it's called a FILLER piece. I can be ordered at dealer or a local junk yard. Just replaced one , cost for part was $15 used.

Apr 21, 2010 | 2004 Toyota Corolla

1 Answer

How do you replace rear tail light assembly?


Open the trunk and along the bottom of the tail light, there should be a Philips screw securing a cover piece. (your car may or may not have this piece)
With the cover off, there will be another 2 screws securing the bottom of the tail light assembly. Remove the screws and pull the bottom out and the top is held in by two retainers that should just slide right out

Oct 13, 2009 | 2001 Toyota RAV4

1 Answer

REMOVE DRIVERS SIDE REAR BUMPER


Its very little problem just go to mechanic for solve thist problem

Jul 12, 2009 | 2004 Toyota RAV4

2 Answers

My Toyota Corolla rear bumper has at big dent on


you have to take the whole bumper off and the bolt the u see holding it on the re-bar and bumper cover should come off

Jul 01, 2009 | 2000 Toyota Corolla

1 Answer

How do I remove the back bumper (plastic) on a 2003 toyota camry?


you can heat the bumper heat gun ( you can rent one i think?)
this will soft the bumper so you push it out easily on the car

1. inside your trunk remove small back clips in trim panel
2. remove tail lamp four 8mm nut perside unplug wires
3. remove black clips under tail lamps ( flat head screwdriver to pull center of the clip up slowly then remove the hole clip)
4. three if the some clips are bottom if the bumper
5. three or four 10mm nuts in side the quarter panel on the right and left side
6.four s shape clips are top bumper that will pull loose
7. with some help slide bumper by pulling it off it
8. when you reinstall the bumper you may need to tape the strophe reinforcement in place

Feb 24, 2009 | 2003 Toyota Camry

1 Answer

Rear bumper on mazda mpv


Removal of the rear bumper on an Mazda 2004 to 2006 MPV.
It's afairly simple task: 1) Open the rear hatch or (door) remove the torx screws at the bottom of the weather strip. 2) Remove both tail lights by unscrewing the two phillip screws on each light, once removed the lights pulling toward the side of the van. Let them hang from the wires. You will see a clip (white in color),pry it out from behind the bumper material and go to the next step. 3) Remove three 8mm head screws in each fender well and three plastic clips. Then remove an 8mm screw at the top corner of the bumper against the rear fender. If your car has splash guards remove them as well. 4) Remove the two clips at the bottom of the bumper attached to the under carriage. 5) Pull the bumper toward the back of the vehicle be careful with the tail lights. Remember, they are hanging loose.
And that's it, you have done it.
Ferni

Oct 07, 2008 | 2005 Mazda MPV

1 Answer

2000 Infiniti I30


Sure! pop the trunk and remove screws and screw covers inside, then look in the wheel wells for the remaining screw/clips. Lastly underneath, near exhaust may be a few last screws to keep from flapping. Just make sure to watch for any wires from rear cameras, or reverse sensors. You will not need to remove any of the foam behind bumper.

Jul 28, 2008 | 2004 Infiniti I35

Not finding what you are looking for?
2004 Toyota RAV4 Logo

Related Topics:

1,522 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...