Question about 1993 Honda Accord

1 Answer

Just replaced with used engine all new belts and waterpump and seals. After driving for ahwile it suerges in idel in park nfor a minute or two. If you restart it it stops. Now that weather has dropped it makes a squeeling sound when you first start it sounds sort of like a belt slipping?

Posted by on

  • Steven Smith
    Steven Smith Nov 09, 2010

    Good as could be expected under the circumstances of the question, Thanks.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

The roll or surging can be due to week map sensor, restarting clears the voltage to the ECU and causes a clean start. This condition can also be caused by a fuel pressure regulator. You will have to troubleshoot this condition as to which parts you reused from your old engine to the new. Your squealing may be just that, a loose belt or idler pulley bearing. If it is present right after start up, look at your voltage / amp meter for hi output from the alternator. Check the battery for proper charge. Hope this helps.

Posted on Nov 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the waterpump on 2003kia sorento lx ?


Water pump is Timing belt driven. It is below the Camshaft sprocket, in the timing case. If you want to repair/replace it here are the instructions.
>

COMPONENTS

REMOVAL
  1. Using the drain plug, drain the coolant.
  2. Remove the drive belt and the engine coolant pump pulley.
  3. Remove the timing belt cover, the auto tensioner and idler pulley.
  4. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  5. Remove the engine coolant pump mounting bolts.
  1. Remove the engine coolant pump assembly from the cylinder block.
INSPECTION
  1. Check the engine coolant Water pump for cracks, damage or wear, and replace the pump assembly if necessary.
  2. Check the bearing for damage, abnormal noise and sluggish rotation and replace the pump assembly if necessary.
  3. Check the seal it for leaks and replace the pump assembly if necessary.
INSTALLATION
>

  1. Clean the gasket surfaces of the engine coolant pump body and the cylinder block.
>

  1. Install the new engine coolant pump gasket and pump assembly. Tighten the bolts to the specified torque. Tightening torque
Engine coolant pump bolt:
Head mark "7": 17 - 22 Nm(170 - 220 kg.cm, 12 - 16 ft. lbs.)
  1. Install the water pump fitting, the thermostat case and the water outlet fitting.
  2. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  3. Install the drive belt, coolant pump pulley and then adjust the auto tensioner.
  4. Refill the coolant.
  5. Run the engine and check for leaks.
Courtesy All Data LLC
© 2015 ALLDATA LLC. All rights reserved. Terms and Condit

Mar 15, 2015 | 2003 Kia Sorento

1 Answer

Diagram of 2009 Honda CRV serpentine belt what is the routing


The parts store you purchase belt from should be able to give you the routing.

Aug 04, 2014 | 2009 Honda CR-V

1 Answer

Need to replace the waterpump.


Hello, 1)Put sealing compound onto a new water pump gasket. Place the new water pump and new water pump gasket onto the cylinder block.
2)Connect the three bolts to the water pump and tighten them to between 15 to 22 feet lbs.
3)Reconnect the heater hose to the new pump. Install the water pump belt onto the pulley, making sure to adjust the tension on the belt.
4)Place a new o-ring onto the water pump inlet and install it, tightening the bolts to 7 feet lbs.
5)Close the draincock on the radiator.
6)Install the water pump pulley onto the drive belt, adjusting the tension on the belt.
7)Reconnect the negative battery cable.
8)Refill the cooling system with coolant to the proper levels. Start the engine and check for leaks when the engine reaches normal operating temperatures.
Thanks

Jun 17, 2011 | 1999 Ford Taurus

2 Answers

Will a broken timing belt damage the valves in 1990 toyota camry v6 dx


No damage will occur. This is a non-interference engine so all you will have to do is make sure the timing marks on the cams and crank are set properly.

Jun 09, 2011 | 1990 Toyota Camry

1 Answer

My toyota 4Runner idels fine when it is in park, but the minute I shift it into drive, before even touching the gas it has a hard shaking idel. What could be wrong?


your problem is the idle air control motor it is not adjusting the idle as you shift out of park, normally engine idle has to be bumped up slightly when in gear. yours is not working must be replaced you will find it at the end of the duct work from the air filter at the intake throttle body.

Nov 16, 2010 | 1995 Toyota 4Runner

2 Answers

Is a 91 tercel 1500 engine a interference engine - Timing belt broke while driving


what do want to find out, , the timing belt broke like that when the are damaged or aged. that why maintaince is neccesary to avoid that

Aug 10, 2010 | 1991 Toyota Tercel

1 Answer

How to replace a waterpump on a 1999 chevy lumina?


The waterpump is located on passenger side of the car. Its location if you were standing looking from the passenger side at the engine is at the top right of the engine.There is a pully at the top of the engine that has 4 10mm headed bolts should be a non grooved pully.Loosen the bolts on that pully with the belt on once you loosen these bolts but do not remove them just yet.Using a 3/8 drive ratchet find the belt tensioner and release the belt making sure you remember the belt routing.Typically the the belt routing is printed on a plastic shroud that is just above the waterpump. Once you have removed the belt take out the 4 bolts that you previously loosened.Remove that pully now and the waterpump is right behind that. Sometimes the pully sticks a bit so you may need to put something behind it to gently dislodge it.There are 5 bolts on the waterpump the head of these bolts are 5/16 or 8mm remove the the five bolts using a quarter inch drive ratchet.Once this is done you may need to dislodge the pump.A dead blow hammer works well or a block of wood and a hammer could be used in a pinch.This should not require alot of force.Just a few taps should do it you are just breaking the gasket seal at this point.Now that the old pump is removed the old gasket needs to be removed from the waterpump housing. make sure all old gasket material is removed so the new one will seal properly.Take out the replacement pump and and line the new gasket on the waterpump once you have done this remove the gasket so you can adhere the gasket in place with a thin coat of rtv or weatherstrip adhesive.Now you ready to reverse the process to put it back on.Just make sure to line up the five bolt holes and your ready to go. Hope this helps.

May 17, 2010 | 1999 Chevrolet Lumina

3 Answers

1995 toyota camry leaking oil from behind the timing belt cover. Isn't this a major repair? Is the leak more than likely a camshaft seal?


If you haven't had the timing belt replace (60,000 miles is the suggested service intervale) this is an overlap of having the timing belt replaced.
If the timing belt is not due for replacement and its the cam shaft seal that is leaking. Its a pretty easy fix. Remove the top timing belt cover , and the crankshaft sensor wiring you may have to remove the front engine mount . Set #1 piston at TDC, Loosen tensioner w/ spring slip off belt. **Remove sprocket pull out old seal with a sharp pick. Greese and install new seal make sure its flush with its bore . Reistall sprocket. Slide belt over Cam sprocket tighten tensioner. Install cover and mount (if applicable) Check timing marks by turning crank two revolutions.
** If CamSprocket Bolt is difficult to remove then remove valve cover and use a 21mm wrench to hold the Camshaft while you crack off Cam Sprocket Bolt.
You will see the groves on the Camshaft where you can place a wrench to hold the shaft.
After you replaced the seal replace the valve cover gasket ONLY IF YOU HAD TO REMOVE THE COVER TO HOLD THE CAM WHILE REMOVING ITS BOLT.

This is about as major as it gets.

May 12, 2010 | 1995 Toyota Camry

1 Answer

How do i replace a water pump on a 1993 geo


1 disconnect battery ground cable
2 drain cooling system
3 on models with a/c, proceed as follows:

a discharge a/c system
b loosen upper and lower compressor bolts and remove compressor drive belt
c remove a/c line from top of radiator shroud

4 remove water pump drive belt
5 remove reservoir tank from radiator bracket
6 remove radiator shroud and fan/clutch from vehicle
7 remove waterpump pulley from waterpump
8 remove timing tensioner and timing belt
9 remove dipstick tube
10 remove alternator mounting bracket at water pump
11 remove water pump mounting bolts and water pump
12 reverse procedure to install, using new gasket and rubber seal

Feb 18, 2010 | 1993 Geo Tracker

Not finding what you are looking for?
1993 Honda Accord Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...