Question about 1996 Toyota Tacoma

1 Answer

Where is the evaporator for my A/c located at? How to remove the evaporator?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Master
  • 881 Answers

Its under dash , behind glove box

Posted on Nov 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is expansion valve located


The Expansion valve is located in the evaporator box

On this year Nissan it's not to bad of a job. The dash doesn't need to be removed like the newer cars.

  1. To replace the expansion valve, you will need to discharge the AC system. Remove the two AC lines from the evaporator.
  2. Then you will need to remove the glove box
  3. Then you will need to unbolt the evaporator box
  4. Tip it back and remove.
  5. Once you have the evaporator box removed, then you can replace the expansion valve. I would also clean the evaporator box as well since you will have it removed.

May 20, 2015 | 1998 Nissan Sentra

1 Answer

Wear is the a/c core located at on a 03 Ford crown vic


the evaporator core is located inside of the heat/ air box inside of the cabin. I believe the dash will have to be removed to remove the air box to access the evaporator core.

Aug 24, 2014 | Cars & Trucks

2 Answers

Where to locate the ac expansion valve for 2003 acura 3.2 tl


  1. Remove the filter lid (A), then pull out the dust and pollen filters (B).

  2. Pull out the evaporator temperature sensor (C) from the evaporator fins.

  3. Remove the screws, carefully separate the upper housing (D) from the lower housing (E), then remove the evaporator core (F).

  4. If necessary, remove the expansion valve (G). Use a second wrench to hold the other fitting on the valve so the evaporator line won't twist. Leave the first fitting loosely connected so you can use it to hold the valve while you loosen the second fitting.

  5. Reassemble the evaporator in the reverse order of disassembly, and note these items:

    • Replace all O-rings, with new ones at each fitting and apply a thin coat of refrigerant oil before installing them. Be sure to use the right O-rings for HFC-134a (R-134a) to avoid leakage.
    • Immediately after using the oil, reinstall the cap on the container, and seal it to avoid moisture absorption.
    • Install the capillary tube (H) directly against the outlet line, and wrap it with electrical tape (I).
    • Reinstall the evaporator temperature sensor in its original location.
    • Make sure no air is leaking from the upper housing and the lower housing fitting.
m1.rjaai003.zoomout.gif m1.rjaai003.zoomin.gif

Apr 25, 2014 | 2003 Acura 3.2TL

1 Answer

Thermostat of Mahidra scorpio


thermostat in AC are located inside your evaporator. remove your compartment box and there you will find your evaporator. inside the evaporator you will find a copper tube. this is the thermostat

Jun 11, 2013 | Cars & Trucks

1 Answer

2008 Ford Taurus X blower motor speed fluctuates high to low. Sometimes, wont run at all. Does not matter if in auto or manual temp control mode. Where is blower motor resistor located?


resistor block is located near your evaporator. remove compartment box, you can see your evaporator. around your evaporator you can see few wires bundled towards evaporator. this is your resistor block

Jun 10, 2013 | Cars & Trucks

1 Answer

Where exactly is the Air Condition expansion valve located ?


expansion valve inside the evaporator housing.you have to remove the whole evaporaror housing from inside car remove evaporator case cover and remove expansion valve from inside evaporator case cover.

Apr 21, 2011 | 1991 Honda Civic

1 Answer

What is the purpose, and what is the proper location of the orifice tube in the air conditioning system on my 1991 chevy silverado?


The orifice tube restricts the flow of refrigerant to the evaporator. This restriction allows high pressure liquid freon to change into low pressure freon before entering the evaporator. The orifice tube is located inside the hose running between the condenser and the evaporator. You'll need an orifice tube removal kit if you are looking to remove it.

Aug 23, 2010 | 1991 Chevrolet Silverado 2500

1 Answer

1999 nissan pathfinder need to know where the expansion valve is located


Hi!!

The expansion valve is located in the High Pressure line very close to the evaporator, in the evaporator/blower housing under dashboard passanger side. To access it, need to remove evaporator.

Don't forget to rate this answer, Good Luck!!

Apr 18, 2010 | 1997 Nissan Pathfinder

1 Answer

Need to replace heater core. 91 Cavalier RS, 4 cyl., 2 litre


  1. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System.
  2. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging.
  3. Remove the bolt connecting evaporator lines to evaporator.
  4. Remove the evaporator lines from the evaporator.
  5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  6. Disconnect the heater hoses from the heater core.
  7. Lower the vehicle.
  8. Remove the evaporator case drain tube.
  9. Remove the inside and outside module attaching bolts and the accumulator mounting bracket bolt.
  10. Remove the IP carrier.
  11. Remove the floor air outlet.
  12. Disconnect the wiring harness from the HVAC module assembly
  13. Disconnect the electrical connections at the following locations:
  1. Remove the HVAC module assembly screw (2) at the top of the module from the mounting bracket. (1).
  2. Disconnect the gray source vacuum line (1). IMPORTANT: DO NOT tilt HVAC module assembly or coolant may leak out.
  3. Remove MODULE from Vehicle

Jul 28, 2009 | 1991 Chevrolet Cavalier

1 Answer

Where exactly is the orifice tube located at on a 1996 (DOHC v6)?


it's in the high pressure liquid line.

A/C Evaporator Core Orifice The A/C evaporator core orifice (19D990) should be replaced whenever the A/C compressor (19703) is replaced for lack of performance (internal damage). The A/C evaporator core orifice, located in the condenser to evaporator tube (19835), cannot be serviced in detail as a component of the line. If replacement is necessary, follow the procedure outlined for Liquid Line Removal and Installation. An orifice tube replacement service kit may be used as an optional service procedure. Refer to Section 12-00 for information regarding the use of an A/C Evaporator Core Orifice Replacement Kit E5VY-19D695-A.
-----------------------------------------------------------------------------------
A/C Evaporator Core Orifice Replacement Kit Installation
  1. Discharge A/C refrigerant system. Refer to System Discharging and Recovery as outlined.
  1. Remove condenser to evaporator tube (19835) from vehicle.
  1. Locate A/C evaporator core orifice (19D990) by three indentations or a circular recess in metal portion of the condenser to evaporator tube.


    A/C Evaporator Core Orifice Location
32c58e1.gif
  1. Note angular position of ends of condenser to evaporator tube so that it can be reassembled in correct position.
  1. Cut a 63.5 mm (2.5 inch) section from condenser to evaporator tube at A/C evaporator core orifice location. Do not cut closer than 25.4 mm (1 inch) from start of a bend in tube.


    A/C Evaporator Core Orifice Section Removed From the Liquid Line
    ea95a2d.gif
  1. Remove contaminants from the two pieces of the condenser to evaporator tube.
  1. NOTE: The inlet half of the condenser to evaporator tube will be positioned against the A/C evaporator core orifice tabs when correctly assembled.

    Lubricate fitting with clean refrigerant oil and assemble orifice tube kit (with A/C evaporator core orifice installed) to condenser to evaporator tube. Make sure flow direction arrow is pointing toward evaporator end of the condenser to evaporator tube, and taper of each compressor ring is toward compression nut.


    A/C Evaporator Core Orifice Kit Disassembled Components
    4280629.gif

Jun 05, 2009 | 1996 Mercury Sable

Not finding what you are looking for?
1996 Toyota Tacoma Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...