Question about 1985 Volkswagen Golf

1 Answer

Front end support is rusting away, the hollow metel arms that connect front end parts to chassis. can front axele support be replaced, and where do I buy the part.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

On a car that old you are looking at junkyards for replacement parts. Most junkyards have an interchange and a parts inquiry service, they can find you parts if they are out there anywhere.
however you will have a hard time finding any parts for vehicles more than 10 years old. contact a junkyard and good luck

Posted on Nov 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 Ford F-150, it has some kind of bumper mounted inside the frame near the front wheels. It's rusted and broke loose, what does it do and what's it for.


IT is a part of the chassis frame and is required for chassis strength and rigidity . If the rust is bad enough I would consider a replacement chassis from the wreckers as welding in parts will do more damage than good.

Feb 19, 2014 | Cars & Trucks

1 Answer

94 ford thunderbird front end wheel assembly chassis bar that connects lower control arm to frame of vehicle in front end.


The bar would be the sway bar.

The parts that connect the sway bar to the lower control arm are called the sway bar links.

Oct 07, 2011 | Cars & Trucks

2 Answers

Need to know how to remove front halfshaft on a 1998 chevy blazer


Google the exact steps...you'll be amazed what you find.

Apr 19, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

How to remove knuckle / hub from front axle? Splines are binding, I've applied a puller, ball and tie rod ends removed and strut to knuckle bolts are loosened. I need to replace the outer CV joint. Any...


most likely the bearings in the hub are rusted to the axel. If you work at it you can use a point air chisel to push the axel shaft out you will have to replace the bearing in the hub. worst case you could take the hub and axel off together and press the axel out in a press. either way you will have to replace the hub bearing.

Mar 20, 2011 | 2000 Kia Sephia

1 Answer

4x4 front end not locking in. front drive shaft is turning but the axels are not turning.


1.are the vacuum lines rusted?

2. there are two nipple like metal tubes that have vacuum lines that go to them(front of cross member) see if one had popped off,

3. there is a controller that controls this,, maybe the problem.

4.) i have plow trucks, they get stuffed with snow, and pop off. or rust out.
5. you have a busted hub.. and $$$ to replace.

front axle turns, floats, till you engage the air operated gears, to 4x4.

Dec 18, 2010 | 1999 Dodge Ram 2500 4WD

1 Answer

STeering wheel is loose and noisy while steering. Sounds like something broke inside.


This might help to understand the steering linkage: REMOVAL & INSTALLATION Fig. 1: Steering linkage used on the Bronco and 4-wheel drive F-150 84928067.gif
Fig. 2: Steering linkage used on the 4-wheel drive F-350 84928070.gif
Fig. 3: Steering linkage used on F-Super Duty chassis/cab 84928071.gif
Pitman Arm EXCEPT F-SUPER DUTY STRIPPED CHASSIS AND MOTOR HOME CHASSIS
  1. Place the wheels in a straight-ahead position.
  2. Disconnect the drag link at the Pitman arm. You'll need a puller such as a tie rod end remover.
  3. Remove the Pitman arm-to-gear nut and washer.
  4. Matchmark the Pitman arm and gear housing for installation purposes.
  5. Using a 2-jawed puller, remove the Pitman arm from the gear.
  6. Installation is the reverse of removal. Align the matchmarks when installing the Pitman arm. Tighten the Pitman arm nut to 170-230 ft. lbs. (230-312 Nm); torque the drag link ball stud nut to 50-75 ft. lbs. (68-102 Nm), advancing the nut to align the cotter pin hole. Never back off the nut to align the hole.
F-SUPER DUTY STRIPPED CHASSIS MOTOR HOME CHASSIS
  1. Matchmark the Pitman arm and sector shaft.
  2. Disconnect the drag link from the Pitman arm.
  3. Remove the bolt and nut securing the Pitman arm to the sector shaft.
  4. Using a 2-jawed gear puller, remove the Pitman arm from the sector shaft. To install:
  5. Aligning the matchmarks, slide the Pitman arm onto the sector shaft. If the arm won't slide on easily, use a cold chisel to spread the separation. NEVER HAMMER THE ARM ONTO THE SHAFT! Hammering on the arm will damage the steering gear!
  6. Install the nut and bolt. Tighten the nut to 220-300 ft. lbs. (298-407 Nm).
  7. Connect the drag link.
Tie Rod and Drag Link EXCEPT RUBBERIZED BALL SOCKET LINKAGE
  1. Place the wheels in a straight-ahead position.
  2. Remove the cotter pins and rust from the drag link and tie rod ball studs.
  3. Remove the drag link ball studs from the right-hand spindle and Pitman arm.
  4. Remove the tie rod ball studs from the left-hand spindle and drag link.
  5. Installation is the reverse of removal. Seat the studs in the tapered hole before tightening the nuts. This will avoid wrap-up of the rubber grommets during tightening of the nuts. Tighten the nuts to 70 ft. lbs. (95 Nm). Always use new cotter pins.
  6. Have the front end alignment checked.
RUBBERIZED BALL SOCKET LINKAGE
  1. Raise and support the front end on jackstands.
  2. Place the wheels in the straight-ahead position.
  3. Remove the nuts connecting the drag link ball studs to the connecting rod and Pitman arm.
  4. Disconnect the drag link using a tie rod end remover.
  5. Loosen the bolts on the adjuster clamp. Count the number of turns it take to remove the drag link from the adjuster. To install:
  6. Installation is the reverse of the removal procedure. Install the drag link with the same number of turns it took to remove it. Make certain that the wheels remain in the straight-ahead position during installation. Seat the studs in the tapered hole before tightening the nuts. This will avoid wrap-up of the rubber grommets during tightening of the nuts. Tighten the adjuster clamp nuts to 40 ft. lbs. (54 Nm). Tighten the ball stud nuts to 75 ft. lbs. (102 Nm).
  7. Have the front end alignment checked.
Connecting Rod RUBBERIZED BALL SOCKET LINKAGE
  1. Raise and support the front end on jackstands.
  2. Place the wheels in the straight-ahead position.
  3. Disconnect the connecting rod from the drag link by removing the nut and separating the two with a tie rod end remover.
  4. Loosen the bolts on the adjusting sleeve clamps. Count the number of turns it takes to remove the connecting rod from the connecting rod from the adjuster sleeve and remove the rod.
  5. Installation is the reverse of removal. Install the connecting rod the exact number of turns noted during removal. Tighten the tie rod nuts to 40 ft. lbs. (54 Nm); the ball stud nut to 75 ft. lbs. (102 Nm).
  6. Have the front end alignment checked.
Tie Rod Ends RUBBERIZED BALL SOCKET LINKAGE Fig. 4: Remove the cotter pin from the castellated nut at the ball stud 88288p02.jpg
Fig. 5: Remove the nut from the ball stud 88288p03.jpg
Fig. 6: Use a tie rod end puller tool to remove the ball stud from the Pitman arm 88288p04.jpg
Fig. 7: Liquid correction fluid makes excellent paint to mark the threads of the tie rod end 88288p05.jpg
Fig. 8: For a more accurate reinstallation, you may measure the tie rod end prior to removal 88288p06.jpg
Fig. 9: After having loosened the nut, unscrew and remove the tie rod end 88288p07.jpg
  1. Raise and support the front end on jackstands.
  2. Place the wheels in a straight-ahead position.
  3. Remove the ball stud from the Pitman arm using a tie rod end remover. NOTE: Optional: paint a mark or measure the length of the tie rod end threads to ease reinstallation in as close to the original position as possible.
  4. Loosen the nuts on the adjusting sleeve clamp. Remove the ball stud from the adjuster, or the adjuster from the tie rod. Count the number of turns it takes to remove the sleeve from the tie rod or ball stud from the sleeve. To install:
  5. Install the sleeve on the tie rod, or the ball in the sleeve the same number of turns noted during removal. Make sure that the adjuster clamps are in the correct position, illustrated, and torque the clamp bolts to 40 ft. lbs. (54 Nm).
  6. Keep the wheels facing straight-ahead and install the ball studs. Tighten the nuts to 75 ft. lbs. (102 Nm). Use new cotter pins.
  7. Install the drag link and connecting rod.
  8. Have the front end alignment checked.
prev.gif next.gif

Sep 18, 2010 | 1996 Ford F150 Regular Cab

1 Answer

I replaced hub on front axel but the noise is


It sounds like it is a front end suspension problem. The following should be checked: upper and lower ball joints, the sway bars links, and even the shocks. Replace what is problematic, and your front-end noise should disappear, if it is a front suspension problem. Hopefully, this will FixYa problem!

Jan 04, 2010 | 2001 Ford Excursion

3 Answers

Scraping pulse noise r front merc sable


Check the condition of the wheel bearings, front and back side if the brake rotor, and the back side of the rim. Everything should be clean, rust build-up can throw everything out of true. The hub or wheel-bearing should be tight and smooth when spun.

May 12, 2009 | Mercury Sable Cars & Trucks

1 Answer

Front drivers side axle removal


There's not any special tools. You need a socket to fit the nut on the end of the axle and a wrench to take the nut and bolt off the bottom ball joint that slides through the control arm. Take a bar, pry down on lower control arm, pulling ball joint out, then pull the upper part out by hand, away from the car, slide axle out of the bearing assembly. Take a pry bar, put between trans and axle, give it a swift, quick ****. The axle should come out. Remember to always put jack stands under the car and be safe. Phil

Jan 09, 2009 | 2003 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...