Question about 2004 Jeep Grand Cherokee

1 Answer

Door panel hi i have an 03 grand cherrokee please can you tell me how to take the driver's door panel off , i have taken the screws out from the arm rest,by the mirror & the handle but its still solid. i live in the uk so getting a work shop manual . thank you

Posted by on

  • mach 1 mike Jun 18, 2008

    thank you very much job done &broken wire fixed.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,036 Answers

Ahh, I'm in UK too.

Most interior panels are held on with screws at the armrests, any fittings points (handles,buttons, speakers etc.) and the rest of it is held in with plastic panel clips.

The best way to diy remove these is to use two steel rulers - one either side of the clips, and lever them off one by one.
Expect a few to break - they are replacable items.
Once inside, make sure you replace any plastic membrane, as this stops wind, and prevents corrosion in winter.

Any other problems just ask.

If this helps, please rate as fixya!

Posted on Jun 16, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove the drivers side power window controls without damaging the interior panel. 2004 grand prix GT 4 door

Remove the screws first. There may be one by the mirror. one at the door handle. two in the arm rest, and then two more under the cup out of the arm rest. Then the panel pops off . use a screw driver and your hand when you get room on the bottom and pry it out and work your way around.

Sep 10, 2011 | 2004 Pontiac Grand Prix

1 Answer

Electric window assembly removal

assume you mean window motor.

remove trim panel. long screws (2) AT ARM REST. dRILL 3/8 INCH HOLES (3) AT THE DIMPLES in the inner panel, for access to the 3 bolts holding the motor in.
from 1994 manual.

  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, proceed to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    1. Mark inner door panel and drill three holes 12.7mm (0.5 inch) as shown.


Oct 28, 2010 | 1992 Mercury Grand Marquis

1 Answer

Drivers side door handle on a 2000 buick park avenue will not work inside ok looks like a big job to take door panel off what do you think thank you

The door panel just snaps on except for the door arm rest, it has two screws on the bottom . Take out the screws and the panel should come off, the arm rest will stay on the door.

Jul 14, 2010 | 1999 Buick Park Avenue

1 Answer

Need a diagram of the fastening of the driver's

no pattern just assemble it the way you took it off. Not much in books on this but a picture. I f you have taken many off you will see this . You just have to try most just unclip and then if clips stay in the door you have to retunr them to the cover a lot of times you will have a few screws one behind door handle one by mirror cover and one in behind the entry lamp center of the door and also older gm's one under the arm rest and then even older a couple screws in the lower carpeted panel. and some you take off the door handle and put tool to push out windeow crank parallel with crank handle. and very hold units unscrew the door lock thingy left top. now do repairs and put back together the way you took apart .

Jan 03, 2010 | 1998 Pontiac Grand Am

1 Answer

Arm Rest on drivers side ''99'' Cherokee

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. then you can pop the armrest out the back fo the panel

Jul 28, 2009 | 1999 Jeep Grand Cherokee

1 Answer

I can't figure out how to remove the toggle from the door panel for the drivers side door mirror.

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. Then you'll need to remove the cover just beside the mirror and you should be able to get to the cables

May 20, 2009 | 1996 Pontiac Grand Am

1 Answer

Drivers side door on my jeep cherokee will not open from inside

most likely the inner door handle has a broken hooking tab for the rod to the latch plate.most door panels are held in place with a few screws around the door pull handle and arm rest than most of the sides and bottom of the door panel are held by plastic snap clips. with a large straight blade screw driver start at a corner of the door panel , slide the blade of the screw driver under the edge of the panel and lightly pry out untill you lossen up one of the clips than slide along the screw driver to the next clip , keep going till the panel is lossened up.

Mar 29, 2009 | 2000 Jeep Grand Cherokee

1 Answer

03 Jeep Grand Cherokee Driver side window

There are about 3 or 4 screws holding some molding at top and around the arm rest remove them. Starting at the bottom or back of panel put a small screwdriver or similar object between panel and metal of door and start prying slowly. You will need to buy replacement clips because usually they break when removing, but they are not that expensive. Just take your time and its not that hard. Had to take both off of wifes jeep to replace motor

Dec 14, 2008 | 2004 Jeep Grand Cherokee

1 Answer

1988 Cadillac Deville drivers window shattered while up

Take the Lights out of the arm rest and you will see more screws.

Dec 09, 2008 | 1988 Cadillac Sedan DeVille

1 Answer

Driver side mirror 2004 Pontiac Grand Am

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Dec 07, 2008 | 2004 Pontiac Grand Am

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides