Question about 2000 Lincoln Navigator

1 Answer

Oil pan can i remove oilpan without removeing engine

Posted by on

1 Answer

Yes the front transaxle crossmember has to be removed and then you can.

Posted on Oct 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010. How do I replace oil pan and gasket?


1 drain oil
2 remove bolts retaining oilpan
3 clean mating surfaces on oilpan and engine block
4 check fit gasket to see if holes line up
5 reattach oilpan to engine block and tighten to specified torque
6 put required lube oil in motor to level and start to check for leaks

Aug 26, 2015 | Chevrolet Malibu Cars & Trucks

1 Answer

How do you change the oil pump in a 1995 chevy lumina 3100


You must remove the oil pan. I do not think you can do this with the engine in the car. If you can remvove the pan from the bottom without engine removal, it would be easy. Most every engine has to be removed to fully remove the oilpan. So my solution is- remove engine, remove oilpan, remove pump, replace pump, pan, and engine.

Dec 04, 2013 | Chevrolet Lumina APV Cars & Trucks

1 Answer

Oo.comi bought 1996 grand jeep v8 the oil was not change as it was needed & it is stopping up the oil pump whAT IS THE BEST WAY TO FIX IT WITHOUT TAKING THE OILPAN OFF


Right off, I know you won't like my answer but in reality, you do need to remove the pan, inspect the pump pickup screen, the pump gears and end plate (or just replace the pump) and inspect the engine bearings (remove lower caps, use plasitgage to check clearances, replace and re-torque bolts).
I'm assuming you have a low gauge reading (or oil light on), or, the engine is tapping or knocking.
You need to verify the actual oil pressure by installing a mechanical pressure gauge (yours is electro-mechanical). If actual pressure hot is 15psi or lower at idle, then the pan needs to come off and you need to find out the reason.
Without removing the pan, only thing you could try would be to get five quarts of engine flush, disable the ignition so the engine does not start, crank it over for about thirty seconds and then let it sit about a week. Then, drain the pan and add new oil and perhaps some marvel oil along with it. I'd be concerned about any undissolved carbon though as it can actually plug up the system worse than before. (why pan removal is better).

Jun 13, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Directions for changing the oil pump


THE OIL PUMP IS LOCATED INSIDE THE OILPAN ON THE BOTTOM OF THE ENGINE! YOU'LL HAVE TO DRAIN THE OIL, AND REMOVE THE OILPAN! ON SOME VEHICLES, YOU HAVE TO UNBOLT THE ENGINE MOUNTS, AND RAISE THE ENGINE ENOUGH TO REMOVE THE OIL PAN, SO YOU CAN GET INSIDE

Mar 01, 2011 | 2000 Chevrolet Blazer

1 Answer

How to do an oilpan on a 88 chevy montecarlo


  1. Disconnect battery negative cable.
  2. Remove air cleaner.
  3. Remove upper fail shroud (V8)
  4. Raise vehicle and drain oil pan.
  5. Disconnect A.I.R. hose at converter pipe (V8)
  6. Disconnect A.I.R. pipe at exhaust manifold (V8)
  7. Remove exhaust crossover pipe at manifold and converter.
  8. Remove starter.
  9. Remove flywheel cover.
  10. Disconnect transmission oil cooler lines at oil pan.
  11. Remove engine mount 'through' bolts on V8. Loosen right bolt and remove left on V6.
  12. Remove oil pan bolts and lower oil pan. Check that forward crankshaft throw and/or counter balance weight are not extending downward so to block oil pan removal. Turn crankshaft, necessary, to put throw on horizontal plane.
  13. Raise engine.
  14. Remove oil pan.
Installation


  1. Clean sealing surfaces on cylinder case and pan.
  2. Check oil pan gasket for damage; replace if necessary.
  3. Apply a small amount of 1052751 or equivalent to front and rear corners of oil pan.
NOTICE: Only a small amount of sealant is required. Excessive amounts of sealant may cause a problem with proper sealing of oil pan.


  1. Install retaining bolts and torque to 9 N.m (80 lb. in.).
  2. Raise engine, if necessary.
  3. Lower engine, install mount 'through' bolts and torque to 50 lb. ft. (65 N.m).
  4. Install torque converter cover.
  5. Install starter.
  6. Install exhaust crossover pipe at manifold and converter.
  7. Lower vehicle.
  8. Install fan shroud.
  9. Install air cleaner.
  10. Fill crankcase with oil.
  11. Connect battery negative cable, start engine and check for leaks.

Nov 30, 2010 | 1987 Chevrolet Monte Carlo

1 Answer

Need diagram for 2000 ford taurus oilpan


Oil Pan - Removal & Installation3.0L Engine
VIN S Engine
  1. Before servicing the vehicle.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Dual converter Y-pipe Transaxle support bracket Oil pan by following the bolt removal sequence shown

    8d11698.jpg
    Fig. Oil pan bolt removal sequence-2000-04 3.0L (VIN S) engine


    2272e92.jpg
    Fig. Oil pan bolt tightening sequence-2000-04 3.0L (VIN S) engine
Hope helps (remember rated and comment this).

Aug 15, 2010 | 2000 Ford Taurus

1 Answer

Oilpan replacement


Is it 4WD? if so, I believe your truck may unfortunately be of the vintage where in order to replace the oil pan you need to either remove the engine or front end. If the oil leak in the pan isn't horrible, you may be better off to invest in a quality steel epoxy. Drain the oil, dry it with brakleen real well and goop it up with epoxy.

Mar 29, 2009 | 1991 Ford F150

1 Answer

1994 oilpan


Remove the starter, remove the flywheel dust shield, remove the motor mounts center bolt, jack the engine as far up as possiable, this will then give you access to the oil pan bolts.

Oct 14, 2008 | 1994 Ford F350 Crew Cab

1 Answer

Oil pan removal


see if anything is stopping you from removeing the oil pan make sure you have a jack r somthing under the oilpan in case it drops make sure all bolts have been removed check for hiden 1s you might be surprised it shoul come free if not come back to me

Sep 20, 2008 | 2001 Audi A4

1 Answer

Removal of oilpan


the engine needs to be supported from the top. your oil pan is most likely hanging up on the oil pump. to remove, the subframe must be lowered abit after you've supported the engine from the top.

Jun 10, 2008 | 1995 BMW M3

Not finding what you are looking for?
2000 Lincoln Navigator Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...