Question about Mitsubishi Pickup

1 Answer

I need tourqe settings for a 1982 mitsubishi truck for flywheel

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 643 Answers

The torque range is from 33-67lbs

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flywheel keeps breaking


By breaking I assume you mean into pieces? The only thing that would cause this is a badly misaligned transmission. Any other problems would cause such vibration you would not drive the vehicle .

Oct 14, 2015 | 1986 Ford Ranger 2WD

1 Answer

Tourqe converter bolts dont line up


possibly wrong torque convertor or flywheel

Dec 25, 2013 | 1991 Plymouth Grand Voyager

1 Answer

Replacing the transmission in my 2000 chevy truck 5.3 four wheel halfton got the tranny and the tourqe converter is still on the flywheel but can't figure a way too loosten the tourqes holding it to...


You'll need a box end wrench and a pry bar. Use the pry bar to hold the ring gear against the motor while you use the box end wrench to remove one bolt. Then rotate the engine with the bar to bring the next bolt around to where you can get the wrench on it. Repeat until you have the bolts off. Do not lose those bolts. If you do they will have to be ordered at the dealer.
When you put the torque convertor back in the transmission it has to go in two steps. It will slide in so far and then you will have to turn and push until it goes in again. If you don't do this the trans will not mount flush with the engine. When it's in the transmission properly it should sit about an inch inside the housing. Hope this helps.

May 06, 2011 | 1999 Chevrolet K1500

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

1 Answer

Where is the flywheel located on this truck


its in the bell housing on the transmission the flywheel is bolted to the crankshaft and either the tourqe converter or clutch is bolted to that.

Dec 16, 2010 | 1998 Dodge Dakota

1 Answer

Tourqe specs for an 07 jeep wrangle flywheel


1. Position the flexplate onto the crankshaft and install the bolts hand tight.
2. Tighten the flexplate retaining bolts to 95 N·m (70 ft. lbs.) in the sequence shown.
3. Install the transmission.


4687c60.gif

Sep 24, 2010 | 2007 Jeep Wrangler Unlimited Rubicon 2...

2 Answers

Need tourqe settings


I do belive it is 18 ftlbs.

Mar 22, 2009 | 1993 Chevrolet Lumina

1 Answer

1982 ford f1504x4 truck


sounds like you need a heavier duty starter. Talk to a starter re builder and tell him the problem and he will probably come up with a heavier starter that will do the job.

Jul 03, 2008 | 1982 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...