Question about 1998 Plymouth Grand Voyager

1 Answer

Fan relay assembly? - 1998 Plymouth Grand Voyager

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,565 Answers

Http://www.youtube.com/profile?user=realfixesrealfast#p/search/0/AdIYm9kM5E0

a nice tutorial on replacement of the radiator fan relay.

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the fuse for motor fan in uplander 2006?


there is 2 fuses that you have to check
one will be in the big fuse assembly in the engine bay, the other probably in the fuse assembly in the cab
If they prove ok then it is possible that the coolant temperature SENSOR is faulty and needs replacing
don't confuse it with the temperature sender which operates the temp gauge.

Aug 10, 2015 | 2006 Chevrolet Uplander

2 Answers

2002 jeep grand cherokee larado is over heating. The cooling fanonly runs if I hotwire it. I changed th thermostat. Temp gauge is reading . Could it be the cooling fan relay if so where is it located. The...


Fan relay is located under pass headlight. Remove light assembly, use 2 1/2 " hole saw to drill hole in plastic housing ,3"from back wall, 3'' from left side.This will put you right over relay. Unscrew two bolts,replace. Relay was $40.... dealer wanted$350 to remove front bumper to replace it.

Sep 02, 2010 | 2002 Jeep Grand Cherokee

1 Answer

I need to remove the cooling fan shroud from my 1995 Lincoln Continental. How is the easiest way to go about this?


Engine Fan REMOVAL & INSTALLATION 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the radiator upper sight shield.
  3. Disengage the electrical connector, then remove the integrated relay control/constant control relay module assembly located on the radiator support.
  4. Disconnect the fan electrical connector. Fig. 1: Disengage the fan electrical connector 86873115.jpg

  5. If necessary, remove the air bag crash sensor.
  6. Unbolt the fan/shroud assembly from the radiator and remove. Fig. 2: Unbolt the fan assembly from the radiator 86873116.jpg
    Fig. 3: Remove the fan from the engine 86873117.jpg
    Fig. 4: Slide the fan as an assembly up and away from the radiator. Be careful not to dislodge the mounting stud on the left side. 93143p56.jpg

  7. Remove the retainer and the fan from the motor shaft and unbolt the fan motor from the shroud.
  8. Installation is the reverse of the removal procedures. Tighten the fan shroud retaining bolt to 23–33 inch lbs. (2.6–3.7 Nm). Tighten the fan shroud retaining nut to 71–106 inch lbs. (8–12 Nm). Fig. 5: Constant control relay module location — 3.8L engines 86873118.gif
4.6L Engine
  1. Loosen the fan clutch-mounting shaft from the water pump hub.
  2. Loosen the fan shroud from its radiator mounting and remove the lower hose from the shroud.
  3. Lift the fan and clutch assembly and the fan shroud from the vehicle.
  4. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch. CAUTION
    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage. To install:
  5. Assemble the fan and fan clutch. Tighten the retaining bolts to 15–20 ft. lbs. (20–27 Nm).
  6. Install the fan and clutch assembly and the fan shroud. Mount the fan clutch shaft to the water pump hub and tighten to 37–46 ft. lbs. (50–62 Nm).
  7. Slip the shroud into the lower mounting clips and install the shroud retaining screws. Fig. 6: Fan and fan clutch assembly — 4.6L engine 84173064.jpg
5.0L Engines
  1. Loosen the fan clutch-to-water pump hub retaining bolts.
  2. If necessary, remove the drive belt from the water pump pulley.
  3. Remove the fan shroud upper retaining screws. Lift the shroud to disengage it from the lower retaining clips.
  4. Remove the fan clutch-to-water pump hub bolts and remove the fan and clutch assembly and the fan shroud.
  5. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch. CAUTION
    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage. To install:
  6. Assemble the fan and fan clutch. Tighten the retaining bolts evenly and alternately to 12–18 ft. lbs. (16–24 Nm).
  7. Install the fan and clutch assembly and the fan shroud.
  8. Install the fan clutch-to-water pump hub bolts.
  9. Slip the shroud into the lower mounting clips and install the shroud retaining screws.
  10. If removed, install the water pump drive pulley and adjust the belt tension; refer to Section 1.
  11. Tighten the fan clutch-to-water pump hub bolts evenly and alternately to 15–22 ft. lbs. (20–27 Nm). Recheck the belt tension.
prev.gif next.gif

Jul 14, 2010 | 1995 Lincoln Continental

2 Answers

Where would I find the fan motor relay


The cooling fan relay on a 1996 to 2000 Plymouth Voyager The SSFR (Solid State Fan Relay) Cooling fan relay is located on the left front inner frame just behind the radiator. The radiator coolant fan relay is located on the inside front of the engine compartment near the left headlight assembly. You have to remove the air filter assembly, then look for a simple square relay with 4 wires running into it. It is mounted with 2 screws. It is the only relay at that location. If it has burned, you will need to replace the pigtail wiring harness.

Remove the air box beside the battery a 10 mm bolt and the relay is a four prong square box bolted on the frame with two 8mm bolts
www.autozone.com

May 26, 2010 | 1999 Plymouth Grand Voyager

1 Answer

Over heated , radiator fan not working


fan not working is one of three problems, the fan motor ,fan relay which is located in the front bumper under the passenger head light assembly,or a wiring problem. first check fuses then check voltage to the fan motor if no voltage check voltage to relay if relay has voltage to it replace relay and check fan motor again

May 23, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Hi i have a 2000 jeep grand cherokee the problem is the elec fan dose not turn on where is the sensor the turn on the fan. the fuels are ok.


This is controlled by a relay module .The location is under the passenger head assembly.Dumb location i know but that is were it is at.There is also problems with the fan assembly it self .Test for power on the red wire at the fan with the ac on this will make the computer tell the relay to start the fan. The relay module is not easy to get at :( i hope this helps .

Aug 11, 2009 | 2000 Jeep Grand Cherokee

1 Answer

WHERE IS THE FAN MOTOR RELAY


usually mounted on the fan housing, with the relay assembly sticking inside the fan housing. Locate the fan housing in the engine compartment and look for a plug and board. Unplug and unscrew the board and lift the relay out of the fan housing. Usually looks like a couple of coils on a circuit board.

Replace and re assemble in reverse order.

Aug 05, 2009 | 1994 Mazda B-Series

1 Answer

My fan also has quit the assembly is new so i


Use a known working relay of the same type and turn on your a/c on high, then put in the relay where the old high speed fan relay was. If it comes on, it's the relay. Try this on low speed as well. If they don't come on when the A/C is on, it could be your pcm/ecu as well. If it doesn't communicate with the sensor, it won't turn on. Check with A/C running to narrow it down. If they work here, look into the engine coolant temperature sensor.

Jul 17, 2009 | 1999 Chrysler 300M

1 Answer

Cooling fan relay


its not an actual relay is like a relay assembly

Constant Control Relay Module (CCRM)


The Constant Control Relay Module is located at the LH front of the engine.

May 27, 2009 | 1999 Ford Escort

1 Answer

Fan assembly and relays


You did something wrong, recheck those relays, bypass the relay at the relay socket, if the fans run then the relays may be wrong, are they factory relays?

Oct 19, 2008 | 1998 Ford Contour

Not finding what you are looking for?
1998 Plymouth Grand Voyager Logo

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...