Question about 2005 Mazda 3

1 Answer

Changing Low Beam Headlamp Replacement 2005 Mazda 3.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,188 Answers

Check out the following:
It's not easy. You need a flashlight. First, take the batter vent assembly off by removing the screw over the headlamp assembly. Open the battery box by snapping off the tabs, lift out, and move the vent to the side. Second, disconnect the headlight wire by pressing down on the opposing tabs located on the side of the connector and pull straight back. Move the wire to the side. Next, peel the rubber fitting around the bulb (located on the back of the headlamp assembly). Look inside the headlamp assembly with a flashlight to see what you got yourself into. You'll have to unhook the retainer wire that holds the bulb in place. This requires you to push the top part of the wire toward the front of the car and lift up. The wire should swing to the left (passenger side) releasing the bulb and bulb housing. Pull the old bulb out of the housing (it might be tight), replace with the new one (try not to touch the glass). Replace the bulb/housing. Make sure the little tap fits back into its slot (upper diver side). Push the wire clamp back over the bulb, pushing up back and down making sure it's hooked and your done. It seems easy once you've done it.
Good luck! EJ Kudelka

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Ford escape right head light stays on after shut down. Checked switch, it's good. Pulled fuse it still stays on. What's going on?


First off you need to know how these thing's work , computer controlled . The SJB - smart junction box , a combination of fuse /relay & computer .
Do you know what DTC'S are ? SJB diagnostic trouble codes < not one's for the engine OBD 2 system . Need a factory or professional scanner to view these code's , Autozone , advance etc... can not read these code's .
Before replacing parts an taking the vehicle apart an checking wiring etc... Checking DTC'S should be the first step. So you know what diagnostic steps to use >
Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU Is Defective SJB CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new SJB. REFER to Section 419-10 . B1472 Headlamp (Low Beam) ON Switch/Circuit Short to Ground SJB Go To Pinpoint Test F . B1510 Flash-to-Pass Switch/Circuit Short to Ground SJB Go To Pinpoint Test F . B1570 Lamp Headlamp High Beam Circuit Short to Ground SJB Go To Pinpoint Test E . B1797 Lamp Headlamp Low Beam Circuit Short to Ground SJB Go To Pinpoint Test D . B2501 Headlamp, Left Low Beam Circuit Failure SJB If the low beam is inoperative, Go To Pinpoint Test D .
If the low beam is always on, Go To Pinpoint Test F . B2503 Headlamp, Right Low Beam Circuit Failure SJB If the low beam is inoperative, Go To Pinpoint Test D .
If the low beam is always on, Go To Pinpoint Test F . B2505 Headlamp, Left High Beam Circuit Failure SJB If the high beam is inoperative, Go To Pinpoint Test E .
If the high beam is always on, Go To Pinpoint Test F . B2507 Headlamp, Right High Beam Circuit Failure SJB If the high beam is inoperative, Go To Pinpoint Test E .
If the high beam is always on, Go To Pinpoint Test F . You would have no clue as to what you were doing without doing this first . Your best bet , take it to a qualified repair shop.

Apr 26, 2018 | 2005 Ford Escape

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

1 Answer

2006 buick allure , automatic low beams do not come on when key starts car


Headlamps
You can use the headlamps two different ways.
?€¢
Place the headlamp switch in the HEAD position for normal operations


?€¢
Place the headlamp switch in the OFF position for automatic lamp control (ALC) operation. During ALC the low beam headlamps are ON for daytime running lamp (DRL) operation in daylight conditions at reduced intensity or low beam headlamps ON at full intensity with exterior park lamps ON in low light conditions. The ambient light sensor is a light-sensitive transistor that varies its voltage signal to the body control module (BCM) in response to changes in the outside (ambient) light level. When the BCM receives this signal the BCM turns ON just the low beam headlamps at reduced intensity for the daytime running lamp (DRL) operation. A resistor wire is used (CKT312) to reduced the voltage which reduces the light intensity for the DRL's function. The ambient light sensor can also turn ON the low beam headlamps and the exterior lamps for automatic lamp control (ALC). Any function or condition that turns ON the headlamps will cancel the DRL operation (this means no reduced voltage to the low beam lights). Thirty seconds after you start the engine with the headlamp switch in the OFF position, the DRL will perform one of two actions:
?€¢
Illuminate the low beam headlamps at reduced intensity in daylight conditions


?€¢
Illuminate the low beam headlamps and exterior park lamps for low light conditions

The DRL operates when the ignition switch is in the RUN position, the parking brake is not set and the transmission is not in the PARK position When these conditions are met and the DRL ambient light sensor indicates daylight conditions the DRL will illuminate
Should have BCM scanned for DTC'S - diagnostic trouble codes , could have DTC'S stored in memory !
DTC B2645 Ambient Light Circuit
The body control module (BCM) monitors the ambient light sensor signal circuit in order to determine if the daytime running lights (DRL) or the auto headlights (ALC) should be turned ON in the AUTO mode. When the BCM senses the ambient light sensor voltage is between 1.75-4.9 volts, either the DRL will be commanded ON or the ALC will be commanded ON.

  1. Turn ON the headlamps.
  2. Ensure that the headlamp dimmer switch is in the LOW position.
Do both low beam headlamps illuminate?
Is only one low beam headlamp inoperative? YES / NO
IF no
  1. Disconnect the lamps switch assembly.
  2. Install a jumper between the headlamp switch headlamps ON signal circuit and ground.
Do the low beam headlamps illuminate?
Do the low beam headlamps illuminate?
Go to Step 18
Go to Step 7

7

  1. Remove the headlamp module.
  2. Install a fused jumper between battery positive voltage and the switched low beam voltage supply circuit.
Do the low beam headlamps illuminate?
Go to Step 8
Go to Step 11

8

Test for the following in the headlamp module control circuit:
?€¢
An open


?€¢
A poor connection


?€¢
A short to ground

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 10

9

Inspect for a poor connection at the harness connector of the lamp switch assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 14

10

Inspect for a poor connection at the headlamp module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 15

11

Test for a short to ground in the low beam voltage supply circuit. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 12

12

Inspect for a poor connection at the harness connector of the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 17

13

Inspect the inoperative low beam headlamp voltage supply and ground circuit for a high resistance, a short to ground, or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 16

14

Replace the lamp switch assembly. Refer to Headlamp Switch Replacement .
Did you complete the replacement?
Go to Step 19
--

15

Replace the headlamp module. Refer to Relay Replacement in Wiring Systems.
Did you complete the replacement?
Go to Step 19
--

16

Replace the inoperative low beam headlamp. Refer to Headlamp Assembly or Headlamp Bulb Replacement .
Did you complete the replacement?
Go to Step 19
--

17

Replace the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections .
Did you complete the replacement?
Go to Step 19
--

18

Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 19
--

19

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 3

IF

Sep 30, 2015 | Buick Cars & Trucks

1 Answer

Were is headlight low beam relay


It is located in the under hood fuse/relay box . It's non -replaceable ,if bad whole fuse box has to be replaced ! The low beam headlamps may be turned ON in 3 different ways:
?€¢
When the headlamp switch in the HEAD position for normal operations


?€¢
When the headlamp switch is in the AUTO position, for automatic lamp control (ALC)


?€¢
When the headlamp switch is placed in the AUTO position, with the windshield wipers ON in daylight conditions, after a 6 second delay

Battery voltage is applied at all times to the coil and switch sides of the LOW BEAM PCB Relay located in the underhood fuse block. When the headlamp switch is placed in the HEAD position, ground from G202 is applied through headlamps ON switch signal circuit to the body control module (BCM), signaling the headlamps ON request. In response to this signal, the BCM applies ground through the headlamp low beam relay control circuit energizing the low beam relay. With the relay energized, battery voltage is applied through the switch side of the relay, the left and right low beam fuses, and the low beam supply voltage circuits illuminating the low beam headlamps. Ground for the left headlamp is provided at G101 and the right headlamp at G100.
Low Beam Relay Test

  1. Ignition OFF, disconnect the C2 harness connector at the underhood fuse block.
  2. Connect a test lamp between the control circuit terminal A5 and B+.
  3. Ignition ON, command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  4. ?‡'
    If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.


    ?‡'
    If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.

  5. If all circuits test normal, replace the underhood fuse block.
  6. Ignition OFF, disconnect the harness connector at the inoperative low beam headlamp. Test for less than 5.0 ohms between the ground circuit terminal B and ground.
    ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

    Connect a test lamp between the supply voltage circuit terminal A and ground. Ignition ON, command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
    ?‡'
    If the test lamp is always ON, test the supply voltage circuit for a short to voltage. If the circuit tests normal, replace the underhood fuse block.


    ?‡'
    If the test lamp is always OFF, test the supply voltage circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the underhood fuse block.

    If all circuits test normal, test or replace the low beam headlamp.

Jun 10, 2015 | 2006 Chevrolet Chevrolet Impala LS

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

Headlights not working


Not a fuse problem , same fuse power's low an high beams . Looking at wiring diagrams an using a DVOM - digital volt ohm meter to test the electrical circuit's is the way to find the problem . The light's staying on for 3 or 4 min's. is a function of the BCM - body control module ! Do you know anything about automotive electrical testing ? Do you know what a wiring diagram is an how to read one . Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. Year , make , model an engine size . Under system click on lighting ,then under subsystem click on headlamps .Click the search button then the blue link. get yourself a cheap DVOM an test the electrical circuit's , this is how electrical problems are solved .
Electric Testing Techniques You Need to Know
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts

Plus reading factory service repair info for how it should work would be a good idea .

Headlamps
The headlamps may be turned on two different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the OFF position, for automatic lamp control (ALC). During ALC, the headlamps will be in day time running lamp (DRL) operation in daylight conditions, or low beam operation in low light conditions. The LH HDLPand RH HDLP fuses, supply battery positive voltage from the underhood junction block to the left and right headlamps. The circuit continues through both low and high beam lamps, then back to the underhood junction block. The low beam and high beam circuits continue to the headlamp switch. The low beam and high beam circuits also provide the body control module (BCM) with both low and high beam inputs. The headlamp switch includes the dimmer switch and the flash-to-pass switch. When the headlamp switch is placed in the HEADLAMP position a path to ground is provided. Ground is provided at G201. Depending on the position of the high/low beam switch, either the low or high beam circuit will now have power and ground.
The LH HDLP fuse in the underhood junction block, supplies battery positive voltage to the automatic lamp control (ALC) headlamp relay coil circuit. The ALC relay switch circuit is connected to the low beam circuit at the headlamp switch. When the headlamp switch is placed in the OFF position, the BCM will automatically turn on the low beams in low light conditions. The BCM energizes the ALC relay, closing the switch contacts and grounding the low beam circuit. Ground is provided at G201. With the headlights in the low beam position, the high beams may be momentarily turned on or flashed with the dimmer switch handle. The flash-to-pass feature is accomplished by pulling the dimmer switch handle toward the driver. The headlights may be switched to high beam with the opposite movement of the dimmer switch lever. When the headlamp dimmer switch handle is pulled toward the driver, the flash-to-pass switch closes grounding the high beam circuit. Ground is provided at G201. Both high beams will remain on until the driver releases the switch handle.
If the driver places the headlight switch in the HEADLAMP position , the headlights will remain on until turned off or the battery runs dead.
Do you know what a factory diagnostic trouble shooting chart is ?

Headlamps Inoperative - Low Beams

Step
Action
Yes
No
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics
1
Did you perform the Lighting System Diagnostic System Check?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Lighting Systems
2
Place the headlamp switch in the HEADLAMP position.
Place the headlamp dimmer switch in the LOW position.
Do the low beam headlamps illuminate?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Disconnect the turn/headlamp wiper switch assembly connector C2.
Connect a 15 amp fused jumper between the headlamp low beam signal circuit and a good ground.
Do the low beam headlamps illuminate?
YES - Go to Step 4
NO - Go to Step 5
4
Inspect for poor connections at the harness connector of the turn/headlamp wiper switch assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 7
NO - Go to Step 6
5
Repair an open or high resistance in the headlamp low beam signal circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you complete the repair?
NO - Go to Step 7
--
6
Replace the turn/headlamp wiper switch assembly. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?
Go to Step 7
--
7
Operate the system in order to verify the repair.
Did you correct the condition?
YES - System OK
NO - Go to Step 3

Dec 24, 2017 | 2002 Pontiac Grand Am

2 Answers

How do I replace the headlight bulb on a 2005 Town Car?


1. Remove the three pin-type retainers, two screws and the radiator defector.
2. Remove the 4 bolts securing the headlamp assembly and remove headlamp assembly.
- Disconnect electrical connector
3. Remove the 3 hex-head bolts and 2 torx-head screws and remove headlamp protective cover.
4. *****Standard low-beam bulb*****
Disconnect the connector from the bulb and remove the low beam bulb.
5. *****HID low beam bulb*****
Release the spring tabs and remove the HID low beam bulb
Disconnect the connector from the bulb
6. *****High beam bulb*****
Disconnect the electrical connector and remove the high beam bulb.
Reverse order to install
dttech_6.gif
.
.

dttech_7.gif

Jan 27, 2011 | 2005 Lincoln Town Car

1 Answer

How to change headlight fo 2005 chevrolet uplander


Headlamp Removal & Installation Bulb Replacement To Remove:
  1. Remove the Headlamp Assembly. Headlamp bulbs gm-06-00-3206.gif

  2. Turn the high/low beam bulb socket counterclockwise to remove.
To Install:
  1. Turn the high/low beam bulb socket clockwise to install.
  2. Install the Headlamp Assembly.
Headlamp Assembly (Park, Turn, Cornering and Side Marker Lamps) To Remove:
Headlamp assembly R &I gm-06-00-3207.gif

  1. Rotate the headlamp assembly retainer pins and pull up to remove.
  2. Remove the mounting bolts.
  3. Disconnect the harness connectors.
To Install:
  1. Connect the harness connectors.
  2. Position the headlamp assembly on the panel.
  3. Rotate the retainer pins and push down to lock in place.
  4. Install and secure the mounting bolts.
prev.gif next.gif

Oct 07, 2010 | 2005 Chevrolet Uplander

1 Answer

How to replace the high beam bulb on a 98 GMC Suburban. What needs to be removed to get to it?


Headlamp Bulb: Service and Repair
REMOVAL PROCEDURE
1. Make sure the headlamp switch is in the OFF position.
CAUTION: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments.
To help avoid personal injury:
- Turn off the lamp switch and allow the bulb to cool before changing the bulb. Leave the lamp switch off until the bulb change is
complete
- Always wear eye protection when changing a halogen bulb.
- Handle the bulb only by its base. Avoid touching the glass.
- Do not drop or scratch the bulb.
- Keep dirt and moisture off the bulb.
- Place the used bulb in the new bulb's carton and dispose of it properly.
- Keep halogen bulbs out of the reach of children
NOTE
: Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause
the bulb to explode when the bulb is turned on. It either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and
wipe the bulb dry.
2. Remove the bulbs from the headlamp capsules by reaching from the engine compartment and by twisting the bulb counterclockwise.
3. Remove the 2 long screws from the top of the radiator support.
4. Pull forward the headlamp assembly (3).
5. Disconnect the electrical connector (2) from the burned out bulb assembly (1).
INSTALLATION PROCEDURE
IMPORTANT
:
- Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
- Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.
1. Install the new bulb assembly (1) into the headlamp assembly (3).
Twist clockwise the bulb assembly.
2. Seat the bulb assembly with the connector facing down.
3. Connect the electrical connector (2) to the bulb assembly.
4. Install the headlamp assembly.
5. Install the 2 long screws through the top of the radiator support.
6. Tighten the screws.

Oct 30, 2009 | 1998 GMC Suburban

1 Answer

Front turn signal bulb replacement


HEADLAMP BULB REPLACEMENT

REMOVAL PROCEDURE

CAUTION: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:

  • Turn off the lamp switch and allow the bulb to cool before changing the bulb.
  • Leave the lamp switch OFF until the bulb change is complete.
  • Always wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • Keep dirt and moisture off the bulb.
  • Properly dispose of the used bulb.
  • Keep halogen bulbs out of the reach of children .
NOTE : Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause the bulb to explode when the bulb is turned on. If either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry.


  1. Open the hood.
  2. Remove the headlamp. Refer to Headlamp Replacement .
  1. Remove the access cover from the rear of the headlamp.
  2. Disconnect the electrical connector from the socket.
  3. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  4. Disconnect the electrical connector from the socket.
  5. Remove the bulb and socket from the headlamp.
INSTALLATION PROCEDURE

IMPORTANT :
  • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket.
  • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.
    1. Position the bulb and socket to the headlamp.
    2. Connect the electrical connector to the socket.
    3. Install the bulb and socket to the housing by rotating the bulb and socket clockwise, locking the retaining tabs to the housing.
    4. Install the access cover to the rear of the headlamp assembly
    5. Install the headlamp

REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the headlamp.
  3. Rotate the bulb and socket counter-clockwise in order to remove the bulb and socket from the housing.
  4. Remove the side marker bulb (3) or turn signal/park bulb (4) from the socket.
INSTALLATION PROCEDURE


  1. Install the side marker bulb (3) or turn signal/park bulb (4) to the socket.
  2. Wipe the bulb with a clean cloth to ensure the bulb is free of any dirt or oil.
  3. Install the bulb and socket to the headlamp by rotating the bulb and socket clockwise, locking the retaining tabs to the headlamp.
  4. Install the headlamp.

Jul 10, 2009 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
2005 Mazda 3 Logo

871 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...