Question about 1994 Pontiac Grand Prix

1 Answer

Steering wheel walbuls - 1994 Pontiac Grand Prix

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Sounds like a bad tire.

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REPLACED STEERING GEAR BOX IN 2003 CADILLAC ESCALADE NOW WHEEL IS OFF CENTERED


IF you have a rack and pinion steering pull the steering shaft of the pinion splines and centre the wheels . Centre the wheel and put the steering shaft back on the splines. If it is master splined then centre the steering wheel and adjust each side tie rod until the wheels are centred . (one in -other out ). Remember that when the wheels are straight ahead then the steering wheel will be slightly to the left (USA) to compensate for the camber of the road.. IF a steering box pull the pitman arm off --centre the wheels and the steering wheel and refit the pitman arm

Mar 02, 2014 | Cadillac Cars & Trucks

Tip

Chevrolet Truck Steering Wheel Removal Instruction


1 Turn the steering wheel from side to side until it locks into place. This will make the process a bit easier, as the wheel won't be turning as you work.<br /><br />2 Remove the horn button in the center of the steering wheel by pulling it off towards you. This will expose the steering wheel nut at the center.<br /><br />3 Unbolt the center bolt from the steering wheel, using the 1/2-inch ratchet, extension and socket. This might free the steering wheel right away, but most likely you'll have to proceed to the next step.<br /><br />4 Position the steering wheel puller on the steering wheel such that the center bolt on the puller is on the center shaft of the wheel. Then thread in the bolts supplied with the puller into the two threaded holes on either side of the center shaft on the wheel.<br /><br />5 Tighten down the center bolt on the steering wheel puller using the 1/2-inch ratchet and socket until the steering wheel pops free. Then remove the steering wheel puller from the steering wheel.

on May 28, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Remove steering wheel on 85 dodge diplomat


Disconnect the negative battery terminal. Remove the horn pad on the steering wheel-Phillips head screws from the back side of wheel. Then loosen the nut on the steering wheel center. Mark the steering wheel to column shaft position, so the wheel goes back in exact same position on the shaft. You may need a steering wheel puller to get the wheel off the shaft, not always, but sometimes the wheel is on pretty tight. Do not hammer on the wheel to get it off, use a puller if needed. These pullers are at parts stores and not expensive.

Dec 31, 2013 | 1985 Dodge Diplomat

1 Answer

Replace steering wheel of toyota corolla 1990 model


The steering shaft has splines that allow the steering wheel to be positioned correctly with the front wheels.
Try tapping behind the streering wheel with a hammer to loosen so you can pull the steering wheel off.
If this does not work then you need a wheel puller to pull the steering wheel off the steering shaft.

Jun 10, 2012 | 1990 Toyota Corolla

2 Answers

How do you take the steering wheel off of a 1986 chevrolet c10


1. Turn the steering wheel from side to side until it locks into place. This will make the process a bit easier, as the wheel won't be turning as you work.

  • 2 Remove the horn button in the center of the steering wheel by pulling it off towards you. This will expose the steering wheel nut at the center.

  • 3 Unbolt the center bolt from the steering wheel, using the 1/2-inch ratchet, extension and socket. This might free the steering wheel right away, but most likely you'll have to proceed to the next step.

  • 4 Position the steering wheel puller on the steering wheel such that the center bolt on the puller is on the center shaft of the wheel. Then thread in the bolts supplied with the puller into the two threaded holes on either side of the center shaft on the wheel.

  • 5 Tighten down the center bolt on the steering wheel puller using the 1/2-inch ratchet and socket until the steering wheel pops free. Then remove the steering wheel puller from the steering wheel.
  • May 28, 2011 | 1986 Chevrolet C1500

    1 Answer

    1997 S-10 Pickup location of horn relay, horn not working. I found 3 relays in club compartment which one is it?


    I would check the horn to see if it gets power with a testlight, and try to ground out one of the leads to see if it sounds. It should have power at all times and the button on the steering wheel controls the ground. That can be a source of the problem as well, the button on the steering wheel may not be grounding out the wire to the horn.

    Can also take apart the steering wheel until you get down to the horn switch contact and try to ground it out with a screwdriver or test light to see if sounds the horn.

    May have to remove the air bag first, though.

    ---
    The following talks about the steering wheel disassembly:

    Steering Wheel Removal & Installation Except Models With Air Bag To Remove:
    1. Disconnect the negative battery cable.
    2. Center the steering wheel so that the front wheels are straight.
    3. If equipped, remove the horn cap from the center of the steering wheel. NOTE: If the horn cap or shroud is equipped with an electrical connector it must be unplugged in order to remove the cap/shroud from the steering column.
      Exploded view of a steering wheel mounting 85388063.gif

      Steering wheel alignment and installation 85388064.gif

    4. Remove the steering wheel-to-steering shaft retainer clip (snapring), then loosen and remove the nut. NOTE: Since the steering column is designed to collapse upon impact, NEVER hammer on it!
    5. Matchmark the relationship of the steering wheel to the steering shaft. Some models may already be equipped with one or more alignment marks. If not, make your own using a permanent marker.
    6. Using a suitable steering wheel puller, such as No. J-1859-03 or equivalent, carefully draw the wheel from the steering column.
    To Install:
    NOTE: Before installing the steering wheel, be sure that the turn signal switch is in the Neutral position. DO NOT mis-align the steering wheel more than 0.8 in. (20mm) from the horizontal centerline.
    1. Align the match marks and carefully fit the wheel onto the steering shaft splines.
    2. Install the retaining nut and tighten to 30 ft. lbs. (40 Nm).
    3. If equipped, install the horn pad.
    4. Connect the negative battery cable. Remove the horn pad 88458p19.gif

      Unplug the horn wire 88458p20.gif

      Loosen and remove the wheel retaining nut 88458p21.gif

      Use a suitable threaded puller to loosen the steering wheel from the shaft 88458p22.gif

      Remove the steering wheel 88458p23.gif

      Matchmark the relationship of the steering wheel to the steering shaft 88458p24.gif

    Models With Air Bag To Remove:
    CAUTION
    These models are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.
    1. Disconnect the negative battery cable.
    2. Disable the Supplemental Inflatable Restraint System (SIR). Refer to Section 6 of this manual for this procedure.
    3. Position the steering wheel so that it is in the horizontal position and the front wheel are straight.
    4. Remove the air bag system inflator module as follows:
      • Make sure the air bag system is disabled and the negative battery disconnected.
      • Turn the steering wheel 90 degrees, this will enable you to gain access to the rear shroud holes-to-inflator module.
      • Insert a prytool and push the leaf spring to release the pin.
      • Turn the steering wheel 180 degrees to access the remaining shroud holes, then repeat the procedure to release the pin using the prytool.
      • Tilt the inflator module rearward from the top to access the module electrical wiring, then disengage the wiring from the module and the steering wheel.
      • Unplug the Connector Position Assurance (CPA) and retainer from the module.
    5. Remove the steering wheel retaining nut and the horn plunger contact. NOTE: Since the steering column is designed to collapse upon impact, NEVER hammer on it!
    6. Matchmark the relationship of the steering wheel to the steering shaft. Some models may already be equipped with one or more alignment marks. If not, make your own using a permanent marker.
    7. Using a suitable steering wheel puller, such as No. J-1859-03 or equivalent, carefully draw the wheel from the steering column.
    To Install:
    1. Align the match marks and carefully fit the wheel onto the steering shaft.
    2. Install the retaining nut and tighten to 30 ft. lbs. (40 Nm).
    3. Install the inflator module as follows:
      • Attach the Connector Position Assurance (CPA) and retainer to the module.
      • Attach the inflator module wiring to the steering wheel and to the module.
      • Install the inflator module by pressing it into the steering wheel enough to engage and latch all four notched pins in the leaf spring. Make sure the wires are not pinched.
    4. Connect the negative battery cable.
    5. Enable the air bag system. Refer to Chasis Electrical.
    prev.gif next.gif

    Oct 13, 2010 | Chevrolet S 10 Cars & Trucks

    1 Answer

    I have a 2002 Yukon Denali and I was wanted to know, how do u change the bulb in the steering wheel?


    Steering Wheel Control Switch Assembly Replacement Removal Procedure
    1. Remove the steering wheel. Refer to Steering Wheel Replacement .
      399638.gif
      tif.gif
    2. Remove the horn switch from the steering wheel.
      755486.gif
      tif.gif
    3. Remove the steering wheel shroud retaining screws from the back of the steering wheel.
    4. Remove the steering wheel shroud from the steering wheel.
      408596.gif
      tif.gif
    5. Remove the steering wheel control switch mounting screws.
      780085.gif
      tif.gif
    6. Disconnect the steering wheel control switch (2) electrical connector (1).
      408598.gif
      tif.gif
    7. Remove the steering wheel control switch from the steering wheel.

    Steering Wheel Replacement Tools Required J 1859-A Steering Wheel Puller
    Removal Procedure
    1. Disable the supplemental inflatable restraint (SIR) system. Refer to Disabling the SIR System in SIR.
    2. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
    3. Remove the horn switch. Refer to Horn Switch Replacement - On Vehicle .
    4. Make an alignment mark in order to note the relationship of the steering wheel to the steering shaft.
    5. Remove the steering wheel nut.
      374820.gif
      tif.gif
    6. Remove the steering wheel, using the J 1859-A .
    Installation Procedure

    Oct 04, 2010 | 1995 GMC Yukon

    1 Answer

    I need to put in another steering collum and I dont know how to do it.its a 91 ford F150.hope you can help me.I got another one out of the junk yard for 125,00 is that a good price .thanks for helping my...


    I'd say $125.00 is a good price for a steering column.

    First, have to remove steering wheel (but I don't have instructions for the steering column. For that, maybe try alldata.com, but that will cost):

    STEERING Steering Wheel REMOVAL & INSTALLATION Without Air Bag EXCEPT F-SUPER DUTY STRIPPED CHASSIS MODELS AND MOTOR HOME CHASSIS MODELS Fig. 1: Remove the screws from behind the wheel - F-150 model without air bag 88288p12.jpg
    Fig. 2: Pull away the cover with the wiring still connected 88288p13.jpg
    Fig. 3: Disconnect the wiring at the steering wheel 88288p14.jpg
    Fig. 4: Matchmark the steering wheel 88288p15.jpg
    Fig. 5: Remove the center nut from the steering wheel 88288p16.jpg
    Fig. 6: Use a steering wheel puller to remove the wheel 88288p17.jpg
    Fig. 7: Remove the steering wheel from the shaft 88288p18.jpg
    Fig. 8: Correct steering wheel installation 84928058.gif
    NOTE: The factory recommends that the front wheels be set in the straight-ahead position and you paint or make chalk marks on the column and steering wheel hub for alignment purposes during installation. Of these two safeguards, it is more important to mark the column so even if the column is moved slightly, the steering wheel can still be repositioned in its original position.
    1. Disconnect the negative battery cable.
    2. Remove the one screw from the underside of each steering wheel spoke, and lift the horn switch assembly (steering wheel pad) from the steering wheel. On vehicles equipped with the sport steering wheel option, pry the button cover off with a suitable prytool.
    3. Disconnect the horn switch wires at the connector and remove the switch assembly. On trucks equipped with speed control, squeeze the J-clip ground wire terminal firmly and pull it out of the hole in the steering wheel. Don't pull the wire out without squeezing the clip.
    4. Remove the horn switch assembly.
    5. Remove the steering wheel retaining nut and remove the steering wheel with a puller. WARNING
      Never hammer on the wheel or shaft to remove it! Never use a knock-off type puller.
    6. Install the steering wheel in the reverse order of removal. Tighten the shaft nut to 40 ft. lbs. (54 Nm)
    F-SUPER DUTY STRIPPED CHASSIS MOTOR HOME CHASSIS MODELS
    1. Set the front wheel in the straight-ahead position and make chalk marks on the column and steering wheel hub for alignment purposes during installation.
    2. Disconnect the negative battery cable.
    3. Remove the one screw from the underside of each steering wheel spoke, and lift the horn switch assembly (steering wheel pad) from the steering wheel.
    4. Disconnect the horn switch wires at the connector and remove the switch assembly.
    5. Remove the horn switch assembly.
    6. Remove the steering wheel retaining nut and remove the steering wheel with a puller. WARNING
      Never hammer on the wheel or shaft to remove it! Never use a knock-off type puller.
    7. Install the steering wheel in the reverse order of removal. Tighten the shaft nut to 30-42 ft. lbs. (41-57 Nm).
    With Air Bag Fig. 9: Remove the air bag module and disconnect the wiring harnesses 88288g00.gif
    CAUTION
    Read the air bag service precautions in Section 6 prior to doing work involving an air bag equipped steering column component. Always wear safety glasses when servicing an air bag vehicle and handling the air bag to avoid possible injury.
    1. Turn the front wheels to the straight-ahead position.
    2. Disconnect the battery-to-starter relay cable for at least one minute to let the air bag back-up power supply discharge.
    3. Remove the air bag module from the steering wheel (refer to Section 6).
    4. Disconnect the horn/speed control wiring from the steering wheel.
    5. Remove the steering wheel retaining bolt.
    6. Install the Differential Bearing Cone Remover/Replacer, No. T77F-4220B1, or equivalent, and remove the steering wheel. Route the contact assembly harnesses through the steering wheel as it is lifted off of the shaft. To install: NOTE: Make sure the front wheels are still in the straight-ahead position prior to installation.
    7. Route the air bag sliding contact wiring through the steering wheel at the 3 o'clock position. Position the steering wheel on the shaft an align the marks. Make sure not to pinch the contact wire. WARNING
      Make sure no air gets trapped between the steering wheel and air bag sliding contact.
    8. Install a new steering wheel retaining bolt, then tighten to 23-33 ft. lbs. (31-45 Nm).
    9. Connect the horn/speed control wiring and clip in place. Connect the air bag wire harness. Tighten the module retaining nuts to 35-53 inch lbs. (4-6 Nm). NOTE: When the battery cable has been disconnected, then reconnected, some abnormal driving symptoms may occur for the first 10 miles (16 km) until the PCM re-learns it adaptive strategy.
    10. Connect the battery to starter cable. Verify the air bag warning indicator light on the instrument panel.
    prev.gif next.gif

    Sep 24, 2010 | 1991 Ford F150

    1 Answer

    Ok i need to know how to assemble the steering wheel


    Steering Wheel Removal & Installation Special Service Tools (SST) Required:
    • J1859-A Steering Wheel Puller
    • J42578 Steering Wheel Puller Legs
    To Remove:
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Place the ignition into the OFF position.
    3. Perform the SIR System Disabling procedure.
    4. Remove the inflator module
    5. Scribe an alignment mark onto the steering wheel hub in line with the mark on the steering shaft.
    6. Loosen the steering wheel nut.
    7. Position the steering wheel nut flush with the end of the steering column shaft.
    8. Loosen the steering wheel using the J1859-A SST.
    9. Remove or disconnect the following:
      • The steering wheel controls electrical connector (if equipped)
      • The horn switch lead from the steering hub
      • The steering wheel nut
      • The steering wheel from the steering shaft
      • The steering wheel controls and the steering wheel controls harness from the steering wheel (if equipped)
    To Install:
    1. Install or connect the following:
      • The steering wheel controls and the steering wheel controls harness to the steering wheel (if equipped)
      • The SIR connector properly routed through the steering wheel
      • The mark on the steering wheel with the mark on the steering shaft
      • The steering wheel CAUTION
        The fastener is prevailing torque type and may only be reused if the fastener and its counterpart are clean and free from rust and the fastener develops 27 inch lbs. (3 Nm) of torque or drag against its counterpart prior to the fastener seating. If the fastener does not meet these criteria it must be replaced.
      • The steering wheel nut
        1. Torque to: 33 ft. lbs. (45 Nm)
      • The horn switch lead to the steering hub
      • The steering wheel controls electrical connector (if equipped)
      • The inflator module
      • Enable the SIR system.
    2. Ensure that the steering Wheel controls operate properly (if equipped).
    3. Ensure proper horn operation.
    prev.gif next.gif

    Jul 03, 2010 | 1997 Chevrolet Venture

    1 Answer

    I need to know how to take off a steering wheel from a 2002 chevy pick up truck


    1 remove negative battery cable 2 remove air bag module from steering wheel, this is usually bolted thru from the back of the steering wheel 3 remove steering wheel retaining nut. 4 Using a steering wheel puller pull steering wheel from steering shaft.

    Mar 16, 2010 | 2002 Chevrolet Silverado

    Not finding what you are looking for?
    1994 Pontiac Grand Prix Logo

    Related Topics:

    16 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...