Question about 1997 Volkswagen Jetta

1 Answer

How do i take an ignition switch off step by step???

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Remove plastic covers surrounding ignition sw.
Place ign key into cylinder.
On the bottom of the cylinder, there will be a small "button" that you must push in when the ignition sw is placed in the accessory position.
Pull switch out with key still in.

Posted on Nov 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I havever a Pontiac Bonneville SSEI 2001, I want to replace the neutral safety switch but I can't find it. Is this where it should be?


Before you replace a part you don't need ! Are you familiar with how the starting system works on this vehicle . Did you test with a scan tool or even a voltmeter to see if the PCM is receiving voltage through the Park neutral safety switch . You can't find it because it is inside the transmission. An it is called Transmission Internal Mode Switch .
Moving the ignition switch to the START position sends a 12 V signal to the PCM Ignition Crank Sense. The PCM verifies that the transmission is in the PARK or NEUTRAL position. The PCM then grounds the control circuit of the START relay. When the START relay is energized it allows battery positive voltage to the starter solenoid S terminal.
Starter Solenoid Does Not Click
2
Turn the ignition switch to the START position.
Does the engine crank?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3

3
Is the security indicator flashing?
YES - Go to Diagnostic System Check - Theft Deterrent in Theft Deterrent
NO - Go to Step 4

4
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, observe the Starter Relay Command parameter in the PCM data list.
Turn the ignition switch to the START position.
Does the scan tool display Yes?
YES - Go to Step 6
NO - Go to Step 5

5
Turn ON the ignition, with the engine OFF.
Verify that the transmission is in Park or Neutral.
With a scan tool, observe the IMS parameter in the Transmission data list.
Does the scan tool display Park or Neutral?
YES - Go to Step 12
NO - Go to Transmission Internal Mode Switch Logic in Automatic Transaxle - 4T65- E
6
Turn the ignition switch to the START position.
Do you hear the STARTER relay click?
YES - Go to Step 9
No - Go to Step 7

7
Turn OFF the ignition.
Disconnect the STARTER relay.
Turn ON the ignition, with the engine OFF.
Connect a test lamp between the battery positive voltage circuit of the STARTER relay coil and a good ground.
Does the test lamp illuminate?
YES - Go to Step 8
NO - Go to Step 20

8
Connect a test lamp between the battery positive voltage circuit of the STARTER relay coil and the control circuit of the STARTER relay.
Turn the ignition to the START position.
Does the test lamp illuminate?
YES - Go to Step 16
NO - Go to Step 14
9
Turn OFF the ignition.
Disconnect the STARTER relay.
Connect a test lamp between the battery positive voltage circuit of the STARTER relay switch and a good ground.
Does the test lamp illuminate?
YES - Go to Step 10
NO - Go to Step 21

10
Connect a 30 amp fused jumper between the battery positive voltage circuit of the STARTER relay switch and the starter solenoid crank voltage circuit.
Does the engine crank?
YES - Go to Step 16
NO - Go to Step 11

11
Does the fuse in the jumper open?
YES - Go to Step 22
NO - Go to Step 13

12
Turn OFF the ignition.
Disconnect the PCM harness connector.
Connect a test lamp between the crank request input circuit of the PCM and a good ground.
Turn the ignition to the START position.
Does the test lamp illuminate?
YES - Go to Step 19
NO - Go to Step 15

13
Test the starter solenoid crank voltage circuit for a high resistance or open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 27
NO - Go to Step 17
13
Test the starter solenoid crank voltage circuit for a high resistance or open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 27
Go to Step 17

14
Test the control circuit of the STARTER relay for an open or short to battery voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 27
NO - Go to Step 19

15
Test the crank voltage circuit of the PCM for a high resistance or open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 27
NO - Go to Step 18

16
Inspect for poor connections at the STARTER relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 27
NO - Go to Step 23

17
Inspect for poor connections at the starter solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 27
NO - Go to Step 24

18
Inspect for poor connections at the ignition switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 27
NO - Go to Step 25

19
Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 27
Go to Step 26

20
Repair an open or high resistance in the battery positive voltage circuit of the STARTER relay coil. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 27
--

21
Repair the open or high resistance in the battery positive voltage circuit of the STARTER relay switch. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 27
--

22
Repair the short to ground in the starter solenoid crank voltage circuit. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 27
--

23
Replace the STARTER relay.
Did you complete the replacement?
Go to Step 27
--

24
Replace the Starter Motor. Refer to Starter Motor Replacement .
Did you complete the replacement?
Go to Step 27
--

25
Replace the ignition switch. Refer to Ignition and Start Switch Replacement in Instrument Panel Gauges and Console.
Did you complete the replacement?
Go to Step 27
--

26
Important:: Perform the set up procedures for the PCM. Refer to Powertrain Control Module Programming in Engine Controls - 3.8L.
Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 3.8L.
Did you complete the replacement?
Go to Step 27
--

27
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jun 30, 2016 | Pontiac Cars & Trucks

Tip

How to remove the ignition key cylinder 2001 chevy malibu


first disconnect the battery.
second you will need the ignition key.

step 1: remove the radio cover
step 2: remove the radio
step 3: remove the 2 bolts holding the ignition switch in place
step 4: work the switch out through the radio hole
step 5: gently unplug the white and the yellow wires from the side of the cylinder
Optional: completely remove the switch by disconnecting the ignition wires and cable.
( you do not have to completly remove the switch if you are just changing the cylinder)
step 6: follow the video
a: put the key in
b: turn key two clicks
c: push the holding pin with a small screwdriver
d: pull the cylinder out

use cation when unplugging and replugging and the white and yellow wires, these are the anti-theft security wires. they plug into the chip on the cylinder. the car will not run without them or if the chip gets damaged.

on Jul 04, 2015 | Chevrolet Malibu Cars & Trucks

1 Answer

No turning signals


Turn Signal Lamps
The turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL, CORN LPS Fuse. Battery voltage is then applied through the TURN SIGNAL, CORN LPS fuse circuit to the hazard warning switch. The hazard switch supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the body control module (BCM) . The front turn lamps are grounded at G101. The rear turn lamps are grounded at G301 and G302.
Turn Signal Lamps and/or Indicators Inoperative

2

  1. Turn the ignition switch to the ON position.
  2. Place the turn signal switch in the LH and RH on position.
Do the turn signals operate properly?
Go to Testing for Intermittent Conditions and Poor Connections yes
Go to Step 3 no

3

Are all of the turn signal lamps and indicators inoperative?
Go to Step 5 yes
Go to Step 4 no

4

Are only the turn signal indicators inoperative?
Go to Step 16 yes
Go to Step 9 no

5

Check the TURN SIGNALS CORN LPS fuse for an open.
Is the TURN SIGNALS CORN LPS fuse open?
Go to Step 25 yes
Go to Step 6 no

6

  1. Disconnect the hazard switch.
  2. Turn the ignition to the ON position, with the engine OFF.
  3. Connect a test lamp between the ignition positive 1 voltage circuit of the hazard switch and a good ground.
Does the test lamp illuminate?
Go to Step 7 yes
Go to Step 27 no

7

Connect a test lamp between the ignition 1 positive supply voltage circuit of the hazard switch and the ground circuit of the hazard switch .
Does the test lamp illuminate?
Go to Step 8 yes
Go to Step 23 no

8

  1. Install a fused jumper between the ignition 1 positive voltage circuit of the hazard switch and the turn signal flasher signal circuit of the hazard switch.
  2. Place the turn signal switch in the RH on position and the LH on position.
Do the turn signal lamps illuminate?
Go to Step 17 yes
Go to Step 15 no

9

Is a front turn signal inoperative?
Go to Step 10 yes
Go to Step 13 no

10

  1. Turn the ignition switch to the ON position.
  2. Disconnect the inoperative front turn signal lamp.
  3. Connect a test lamp between the supply voltage circuit of the inoperative front turn signal lamp and a good ground.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 14 yes
Go to Step 11 no

11

  1. Disconnect the body control module (BCM) connector.
  2. Connect a test lamp between ground and the front turn signal switch signal circuit of the BCM.
  3. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 12
Go to Step 22

12

Test for an open or for a high resistance in the supply voltage circuit of the inoperative front turn signal lamp. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 21

13

  1. Turn the ignition switch to the ON position.
  2. Disconnect the inoperative rear turn signal lamp.
  3. Connect a test lamp between the supply voltage circuit of the inoperative turn signal lamp and a good ground.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 14
Go to Step 28

14

Connect a test lamp between the ground circuit of the inoperative turn signal lamp and supply voltage circuit of the inoperative turn signal lamp.
Does the test lamp illuminate?
Go to Step 20
Go to Step 26

15

Test for an open or high resistance in the turn signal flasher signal circuit. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 18

16

  1. Turn OFF the ignition.
  2. Disconnect the instrument panel cluster (IPC).
  3. Connect a test lamp between the supply voltage circuit of the inoperative turn signal indicator and the instrument panel cluster (IPC) ground circuit.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 19
Go to Step 24

17

Inspect for poor connections at the harness connector of the hazard switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 30

18

Inspect for poor connections at the turn signal switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 29

19

Inspect for poor connections at the instrument panel cluster (IPC). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 31

20

Inspect for poor connections at the inoperative turn signal lamp. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 32

Sep 05, 2015 | 2001 Oldsmobile Intrigue

1 Answer

Program key fob


  1. Close all vehicle doors.
  2. Insert the key into the ignition.
  3. Hold down the power UNLOCK button on the driver's door panel-continue to hold down until instructed to release in step 9.
  4. Perform steps 5 through 8 in fairly rapid succession.
  5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
  6. Turn the ignition switch to the OFF position.
  7. Turn the ignition switch to the ON position.
  8. Turn the ignition switch to the OFF position.
  9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
  10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
  11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
  12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

Mar 12, 2015 | 2002 Chevrolet Chevrolet Tahoe

1 Answer

How do i program a keyless remote for a chevy 2002 S10?


1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.

Mar 05, 2010 | 2002 Chevrolet S-10

1 Answer

Battery went dead in 2007 Chevy Silverado truck. Now, remote does not work. Replaced battery in remote and it still does not work.


Make sure you have one working ignition key and all remotes for the vehicle.

1) Close all vehicle doors.
2) Insert the key into the ignition.
3) Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
4) Perform steps 5 through 8 in fairly rapid succession.
5) Turn the ignition switch to the ON position (as far as you can go without starting the engine).
6) Turn the ignition switch to the OFF position.
7) Turn the ignition switch to the ON position.
8) Turn the ignition switch to the OFF position.
9) Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
10) Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
11) Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
12) Turn the ignition switch OFF then to the ON position in order to exit the transmitter programming mode.

Feb 28, 2010 | 2007 Chevrolet Silverado 1500 2WD

1 Answer

How do i remove ignition switch on a 1991 f150 ?


HI, follow the steps below to help with this issue.



Step 1

Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them.

Step 2

Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

Step 3

Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

Step 4

Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

Step 5

Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

Step 6

Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.



Jul 11, 2009 | 1991 Ford F150

1 Answer

Lost working keys extra will unlock but does not start how do i program extra key to start car


On 2002 model try the following:
1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.


from ProgramyourRemote

Jul 04, 2009 | 2002 Chevrolet Tahoe

1 Answer

Need the procedure to program my new remote...THANKS!!!


1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.

May 20, 2009 | 2005 Chevrolet Silverado

1 Answer

Reprograming a keyless remote


program transmitter code(s) as follows:
1) Confirm that all the doors are closed and the ignition key is out of the ignition cylinder.
2) Open the driver’s door. Insert the key and turn the ignition switch to ON position within 10 seconds.
3) Turn the ignition switch to OFF position within 10 seconds, remove ignition key from lock cylin-der.
4) Push and release the driver’s door switch (1) 3 times within 20 seconds.
5) Insert the ignition key and turn the ignition switch to ON position within 10 seconds.
6) Turn the ignition switch to OFF position within 10 seconds, remove ignition key from lock cylin-der.
7) Press and hold both LOCK and UNLOCK buttons (2) on the transmitter (3) for more than 5 seconds
within 20 seconds of removing the ignition key from the lock cylinder in step 6.
8) Press LOCK or UNLOCK button (2) on the transmitter (3) within 5 seconds (after step 7). All the
doors will lock/ unlock to confirm that this process has been properly done.
With this process, the transmitter has been programmed.
9) If you want to program an additional transmitter, repeat the procedure from Step 1) through Step 8).
10) Make sure that the keyless entry system properly operates by operating each transmitter.

Nov 08, 2008 | 2000 Chevrolet Tracker

Not finding what you are looking for?
1997 Volkswagen Jetta Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...