Question about 1992 Toyota Corolla

1 Answer

The coolant temperature sensor wires came undone and I need to know how to connect them back.

Posted by on

Ad

1 Answer

Undone how?

Backed out of terminals?

Release the terminals from connector and remake,then solder

Posted on Nov 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code p1115


The Engine Coolant Temperature Sensor measures the rise and fall of the Engine Coolant Temperature. Common Problems That Trigger the P0115 Code Defective Engine Coolant Temperature Sensor Rusty and/or corroded Engine Coolant Faulty or corroded Engine Coolant Temperature wiring or connections

Sep 25, 2014 | 2000 Kia Sportage

1 Answer

89 dodge ram truck 2500 2wd code reader says 4 codes dont know what they mean p1509, p1298, p0118 andp0113


P1509 Dodge - Leak Detection Pump Switch or Mechanical Fault

P1298 Dodge - Air/Fuel Ratio Lean Under Wide Open Throttle Condition
- Plugged air filter
- Plugged fuel filter
- Defective fuel pump
- Ignition system weak-misfires
- Defective coil

P0118 Dodge - Engine Coolant Temperature Sensor Circuit High
- Low engine coolant level
- Faulty Engine Coolant Temperature (ECT) sensor
- Faulty engine coolant thermostat
- Engine Coolant Temperature (ECT) sensor harness is open or shorted
- Engine Coolant Temperature (ECT) sensor electrical circuit poor connection

P0113 Dodge - Intake Air Temperature Sensor 1 Circuit High
- Faulty Intake Air Temperature (IAT) sensor
- Dirty air filter
- Intake Air Temperature (IAT) sensor harness is open or shorted
- Intake Air Temperature (IAT) sensor circuit poor electrical connection

Dec 16, 2013 | Cars & Trucks

1 Answer

Location of engine coolant temperature sensor


Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.


12_5_2011_5_38_05_pm.jpg

Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

Dec 05, 2011 | 2000 Ford Escort

1 Answer

I want to replace cooling temperature sensor but I can't locate where it is? I have a Haynes Repair Manual book but it is not clear. My car is Volkswagon Jetta TDI 2000. Does anyone know please give me...


COOLANT TEMPERATURE SENSOR THREADS INTO A COOLANT PIPE NEAR THE COOLANT OUTLET.LOOK AT SMALL COOLANT PIPES AT RADIATOR.YOU WILL SEE A SENSOR WITH WIRES CONNECTING TO IT.WITH COOLANT COOLANT HOSES CONNECTED TO IT.COOLANT TEMPERATURE SENSOR IS BETWEEN TWO COOLANT HOSES CANT MISS IT.YOU HAVE TO SQUEEZE CLAPS ON HOSES WITH PLIERS IN ORDER TO REMOVE HOSES FROM COOLANT SENSOR.

Apr 13, 2011 | 2000 Volkswagen Jetta TDI

1 Answer

Need to know where the coolant temperature sensor is located on a 2002 Lincoln ls 3.9 V8 engine any help would be highly appreciated


The coolant temperature is read off of the (CHT) cylinder head temperature sensor. It is located on the inside on the passenger side (right) cylinder head and is connected to the harness through Ford connector C107. The Ford basic part# is 6G004. It's connected by WH/VT and BR/WH wires to pins 40 and 17 of the vehicles PCM (computer). Keep in mind that if the coolant level is low, if there is air in the system, or if there is a wiring concern, you could have concerns with this sensors reading. Good luck.

Apr 04, 2011 | 2002 Lincoln LS

1 Answer

The check enging light comes on then goes off. I foud out the code po118 engine coolant temp circut high input. is it the coolant temp sensor. if so how do I replace it. It is on a 2004 jetta tdi


According to Autozone.com:

Because ECT (engine coolant temperature) sensor procedures vary depending upon their location, first locate the part. You may need to partially drain the engine coolant to prevent coolant spillage.
  • Disconnect the negative battery cable.
  • Unplug the ECT.
  • Then, unscrew it.
  • Reverse the removal procedures to install the new part.
  • Connect the negative battery cable to the battery.



    Related Parts:
---
Coolant Temperature Sensor printpage_icon.gif



0900c152801bfc38.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the coolant temperature sensor
The coolant temperature gauge sensor is a temperature-variable resistor, or thermistor. As coolant temperature increases, the resistance of the sensor decreases or decreases, depending on the type of sensor.
A1 and A2 platforms use a different type of circuit that A3 vehicles. On A1 and A2 vehicles, the circuit is a "resistance to ground" type. A3 vehicles use a "variable voltage" type, where a voltage is supplied to the sensor. Because of the circuitry design on A3 vehicles, testing of the coolant temperature gauge is limited.
The engine coolant temperature gauge uses a heat sensitive sending unit to transmit an electrical signal to the gauge. The sending unit is a heat sensitive variable resistor that is located on or near to the cylinder head and threads into an engine coolant passage. The sensors are a Negative Temperature Coefficient (NTC) type. As the temperature increases, the electrical resistance of the sensor decreases. As the coolant temperature changes, so does the resistance of the sensor. The gauge is calibrated within the operating range of the sensor and interprets the resistance value to display the coolant temperature.
Beginning with model year 1994, the engine coolant gauge and the Engine Control Module (ECM) temperature sensors were combined into one sensor with 4 terminals. The basic operation remains the same in that their resistance decreases as the coolant temperature increases, however the actual resistance values of the 2 sensor circuits are different. The electrical connector of the 4-wire terminal sensor ( 1 and 2 ) is keyed to prevent improper connection of the sensor's electrical circuit.

0900c152801bfc39.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Beginning with model year 1994, the Engine Coolant Temperature Sensors combined the sensors for the ECM and the gauge into one sensor-1997 2.8L V6 sensor shown


0900c152801bfc3a.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. The electrical connector for the combined temperature sensors is keyed to avoid improperly connecting the sensor's wiring-1997 2.8L V6 connector shown

Oct 17, 2010 | 2004 Volkswagen Jetta

2 Answers

My low coolant light stays on although water level is okay. I have a 1997 Mercury Cougar.


Hi the problem you are having is with the low level sensor this is located in the coolant filler cap and all you need to do is get this replaced, they are not expensive to buy and it will solve your problem.

first check the wires are not loose or shorting give them a good wiggle and see if the warning light goes off also get someone to press the switch by hand and see if that turns the light off or not.

let me know if you need further assistance ok

plz rate this solution as i have a whole page of unrated posts, thanks

Sep 15, 2010 | Mercury Cougar Cars & Trucks

1 Answer

Oil temperature 90 C, coolant temperature 0 C. Where is the senso


not easy.
back of the engine , below intake boot.
4 wire sensor.

Apr 13, 2010 | 2000 Audi A6

1 Answer

Error code po0117. Vw beetle


16501/P0117 - Engine Coolant Temperature Sensor (G62): Signal too Low Possible Symptoms
  • Difficulties with starting a cold engine.
  • Starting the engine when engine is warmish or warm, idle rpm immediately is 1200 - 3000 rpm.
  • RPM at idle is irregular.
  • With all engine temperatures seldom idle rpm will vary between 900 - 1000 rpm.
  • With engine warm (90 °C) the engine temperature suddenly drops (70 °C) and slowly comes back to 90 °C.
  • Bad acceleration during warming up.
    • Diesel: an indication is extreme long time burning time of the glow indication light.
Possible Causes
  • The electrical signal coming from G62 is too low
  • Wiring and/or connections faulty (short circuit?)
  • Engine Coolant Temperature Sensor (G62) faulty
Possible Solutions
  • Check wiring and connections
  • Check / Replace Engine Coolant Temperature Sensor (G62)
Special Notes
  • In MY 1995-2002 (?) in Europe at VW-cars the G2/G62 had the bad reputation of breaking down often. The default G2/G62 is black and all replacements are green.

Mar 21, 2010 | 1999 Volkswagen Beetle

3 Answers

Where is the temperature sending unit on a 1999 VW Passat located.


VW Passat & Audi A4 1990-2000

Motronic System
The Engine Coolant Temperature (ECT) sensor is mounted in the water outlet on the back side of the head. If you vehicle still has a original VW part it will be black in color with a four terminal connector. This device signals the engine management system with the current coolant temperature, the ECU takes this information and uses it to control other such circuits as the idle speed, knock control system, oxygen sensor circuit, exhaust gas recalculation, and fuel tank venting. It is also important to note that if at any time ECU does not receive a signal from the ECT it will substitute a value of 176°F (80°C).

VR6
The Engine Coolant Temperature sensor is mounted in the thermostat housing. The body of the sensor will be blue and the sensor will be blue and have two terminals if it is an original factory VW part.


The engine coolant temperature gauge uses a heat sensitive sending unit to transmit an electrical signal to the gauge. The sending unit is a heat sensitive variable resistor that is located on or near to the cylinder head and threads into an engine coolant passage. The sensors are a Negative Temperature Coefficient (NTC) type. As the temperature increases, the electrical resistance of the sensor decreases. As the coolant temperature changes, so does the resistance of the sensor. The gauge is calibrated within the operating range of the sensor and interprets the resistance value to display the coolant temperature.On models produced prior to 1994, the engine coolant gauge temperature sensor is a single wire terminal sensor.

Beginning with model year 1994, the engine coolant gauge and the Engine Control Module (ECM) temperature sensors were combined into one sensor with 4 terminals. The basic operation remains the same in that their resistance decreases as the coolant temperature increases, however the actual resistance values of the 2 sensor circuits are different. The electrical connector of the 4-wire terminal sensor (1 and 2) is keyed to prevent improper connection of the sensor's electrical circuit.

WARNING When trouble shooting electrical components, always consult a wiring diagram for the particular year, make and model to ensure proper test equipment connection and diagnosis. Failure to use suitable test equipment and testing methods could permanently damage the electrical component(s).

225902c.jpg

Fig. Beginning with model year 1994, the Engine Coolant Temperature Sensors combined the sensors for the ECM and the gauge into one sensor-1997 2.8L V6 sensor shown


2ae243e.jpg

Fig. The electrical connector for the combined temperature sensors is keyed to avoid improperly connecting the sensor's wiring-1997 2.8L V6 connector shown

I hope help you with this, good luck (remember rated this help).

Oct 13, 2009 | 1999 Volkswagen Passat

Not finding what you are looking for?
1992 Toyota Corolla Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...