Question about 1984 Ford F 150

1 Answer

Replaced key and switch, main ignition and the starter solnoid with no start. tested the solnoid engine turns. electronic in cab work as while. help

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,422 Answers

I know a lot about fords from the eightys i have an 85 iv;e had it for 23 years runs great Im sure i could help you but you need to give more information about what the problem think about it and get back to me Then i can give you some answers

Posted on Nov 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fixed wont start engine..


test the following and fix it. GOD BLESS you.fe35589e-c7d2-4fa3-a813-99841956a6cb.gif
If nothing happens when you turn the ignition key to the "Start" position, it means that the starter motor doesn't turn over the engine. Most commonly this could be caused by a dead battery;
If the battery checks out OK, but the starter still won't crank, there could be a number of possible reasons. Here are some of them:

The ignition switch could be bad - it's a common problem. An ignition switch is an electrical switch installed at the back of the ignition lock mechanism. If jiggling the key in the ignition helps start the car, the ignition switch should be checked first.
The starter solenoid control wire could have a bad connection.
The starter motor itself or a starter solenoid could be bad.
A neutral safety switch is bad. If a car doesn't start with the transmission in Park, but starts in Neutral, it could be caused by a problem with a neutral safety switch.
.
A problem with vehicle's security system or some other electronic control module (e.g., ECM, BCM) may also prevent the starter from operating.

Jul 27, 2013 | 2004 Chevrolet Aveo

1 Answer

How to test ignition switch 1994 nissan


Check the harness for any missing wires, its the main bundle of wires under the dash. If all is in place then check the fuses to see if any needs to be replaced. If all are tested and working, check the relays located in the main engine compartment. If all are intact and working, check the ground wires that connect to the frame of the engine and body or directly to the negative of the battery. The main wires you need to see that are connected is on the alternator, starter, and battery.

Hope this hepls

May 06, 2012 | 1994 Nissan Pickup

3 Answers

I have a 1991 nissan king cab and when i turn the key to on, all electronics in the cab work, fan lights radio ect, then i turn it to start and nothing happens, not a click not turning over nothing....


You could be correct, if the starter solenoid is bad and not making contact it will kill the entire electrical system and also not engage the starter motor. I would replace the solenoid. Please rate this answer, thanks.

Feb 01, 2011 | 1991 Nissan King Cab

2 Answers

I drove my 1999 accord EX to work & 8 hrs. later I tried to start it and it did nothing. Tried jumping still nothing. Put new battery on and it still did nothing.What is the problem?


Hi, diagnosing a no-start condition requires a logical approach to figuring out what might be preventing your car from starting. First, if the engine won't even crank over when you turn the ignition to START, your car obviously won't start.
When you turn the ignition key to start your car, voltage from the battery flows through the ignition switch to the Park/Neutral safety switch and/or brake pedal or clutch pedal safety switch (you have to push the pedal down before the circuit will complete) to the starter relay or solenoid. When the relay or solenoid is energized by voltage from the ignition switch circuit, it closes a contact that routes more power from the battery directly to the starter to crank the engine. The starter motor spins, pushes the starter drive gear to engage the flywheel and cranks the engine.

If the engine fails to crank, there is a fault in one of the components in the battery/ignition/starter circuit.

Ten Reasons why you car won't start..
  1. Low battery (Check battery voltage, recharge if low, or jump start with another vehicle or battery charger).
  2. Loose or corroded battery cables (Inspect, clean and tighten BOTH ends of BOTH battery cables).
  3. Bad starter relay wiring connections or ground connection (Inspect, clean, tighten wiring connections).
  4. Bad starter relay/solenoid (Check for voltage at relay, if relay has voltage but there is no "click" when key is turned to start, replace relay).
  5. Bad starter (Jump battery voltage direct to starter to see if it spins, or remove starter and have it bench tested at auto parts store).
  6. Damaged starter drive or teeth on flywheel (Remove starter and inspect drive gear and flywheel teeth, replace damaged parts if necessary).
  7. Bad ignition switch (Check to see if voltage reaches starter relay/solenoid when turn to start. If not, check for open P/N switch and brake or clutch pedal switch. Replace ignition switch if defective).
  8. Open P/N safety switch, or open Brake Pedal Safety Switch (automatic transmission) or open Clutch Pedal Switch (manual transmission). Bypass switch with jumper wire to see if engine cranks, or use test light or voltmeter to check for voltage passing through switch when ignition is turned to start.
  9. Engine seized due to bearing failure or internal damage (Use socket and long handle to see if engine can be turned by hand, if not engine is locked up).
  10. Engine hydrolocked due to coolant leak from leaky head gasket (Use socket and wrench to see if engine rotates, remove spark plugs and see if coolant comes out or engine can not be cranked with plugs out).

Hope it helps identify and solve the problem

Jan 16, 2011 | 1999 Honda Accord

2 Answers

1998ford f150 starter won't crank or turn over.full charged battery.starter ingages when crossing small hot bolt with upper larger bolt.clicks with ignition.


First make sure you can turn engine over with a socket and that it is not seized. Second if engine checks out fine does the starter just click with the ignition key? If it does perform what is called a voltage drop test on the starter cables. Connect a volt meter on each end of the cable you are testing you should read no more that a half a volt drop when loading the circuit. If cables check out fine pull the starter and have it bench tested at an auto parts store. But be carefull bench testing can show a starter is ok with out putting a load on it, if it still shows good on the bench you still may need to replace it. If you don't get a click with the key check for 12 volts at the starter connector unplugged, if no trace starter wire noting color code back through the starter safety switch back to the ignition switch.

Oct 14, 2010 | 1998 Ford F150 Regular Cab

1 Answer

Key want work 2001 ford ranger, it will turn ignition but want crank truck.


CHECK VOLTAGE AT STARTER BIG WIRE COMES FROM BATTERY, SMALL WIRE FROM IGNITION SWITCH , WITH TEST LIGHT CHECK VOLTAGE AT SMALL WIRE WHILE SOME ONE TURNS KEY TO START POS. IF THERE IS VOLTAGE STARTER NO GOOD. IF NO VOLTAGE CHECK IGNITION SWITCH AND SAFETY NEUTRAL SWITCH.

Nov 06, 2009 | 2002 Ford Ranger Regular Cab

2 Answers

All electronic accessories work when key is in


test power at the starter's power wire. If there is voltage, replace starter. If there is no power, check fuses/relays, if those are fine, check ignition switch (there is a recall on this since 2002). Typical symtoms of ignition switch failure on these vehicles include: Some warning lights not lit when key is turned to ON (ABS, battery, check engine, oil light etc.), Intermitted hard start/No start, stalling while driving, intermitted guage failure. If it is an ignition switch failure, call your local honda dealer for possible free repair under the recall(have your VIN# at hand). hopefully this helps

Sep 11, 2009 | 1998 Honda Prelude

1 Answer

1998 buick lesabre wont start


Do you have a Chip in the Key? if so that Could be the Problem,Ya see the chip is a resistor and if it looses its ELECTRONIC VALUE in its Case Resistance it wont start to test this Turn the Key in the ON posission then do the Screwdriver thing If it Starts Key is Good and Most Likely the Ignition (SWITCH) is Bad <<ELECTRICAL Side NOY LOCKEST SIDE For More Info Recontact Me
rejakwilson@aol.com<<<<<<<<<<<<<<<

Dec 23, 2008 | 1998 Buick LeSabre

2 Answers

95 F150 wont crank


the starter should be replaced. The solenoid is kikcing the pinion out but there is no contact being made to turn the starter motor. I have the exact same truck and before i changed the starter used the old starter tap trick. Tap the starter casing with a hammer and it should start turning again. hope this was helpful for you. Good luck.

Sep 16, 2008 | 1995 Ford F150 Styleside Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...