Question about 2001 Honda CR-V

Open Question

2001 honda crv - my tail lights are out - took off light cover and can find only 3 bulbs - blinker, brake and back-up - they all work. also checked fuses - all OK. Where is the tail light bulb? thanks. Jay.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: replace tail light bulb

open hatch, look for two screws, remove , push tail light gently back and forth to release from clips pull light assembly out , twist bulb socket to remove from housing, replace bulb.

Posted on Sep 19, 2008

Ad
  • 651 Answers

SOURCE: both brake lights do not work

try changing the bulbs

Posted on Dec 02, 2008

johnny5846
  • 379 Answers

SOURCE: 2001 dodge neon tail lights inop

looking at your schematics and , you say tail lights don't work , you didn't mention if front parking lights and license plate lights are working , they all come from the same source , a black /yellow wire , a good clue if front work and rear don't , please advise .if fronts work then you have a open circuit somewhere between junction S118 (near breakout for left headlamp) and rear sockets.

Posted on Dec 31, 2008

  • 15 Answers

SOURCE: 2005 Honda CRV dome light goes out, but not burned out

Without seeing it, I would guess that you have a problem with clean contacts. Especially in cars with smokers, the contacts of something like a fuse or a light bulb can become corroded just enough to stop the light from working. Wiggling it scrapes away the debris and allows for contact. I suggest that you take some steel wool and lightly scrub the contact points on both the light and the fixture. **Be sure to have all the doors closed so you dont short out the steel wool.** If you are concerned with the abrasive nature of the steel wool, a pencil eraser will sometimes work just as well. Either way, it just sounds dirty which is par for any car. Good luck!

Posted on Feb 27, 2009

  • 1 Answer

SOURCE: 2001 ford explorer sport trac

Just found the answer on another site. Sure enough went out removed the 3 philips head screws in the steering column opened it up and walla a wire connection had pulled itself free. When my son uses my truck he always uses the tilt steering, when I get in I have to readjust it. because of this the wire connection pulled itself out. I simply pushed it back in an blinker and brake light are now working. My husband is now trying to figure a way to secure the wire connection so it doesn't pull itself out again. Hope this helps others, either by saving the cost of a dealership or machanic or from getting rear ended.

Posted on Mar 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2008 f350 cab and Chasse front blinkers work but my back blinkers and brake lights don't work


brakes and turn signal lights work together not tail and turn your mistaken

Jul 15, 2017 | Cars & Trucks

1 Answer

Seems like the brake/tail light bulbs are backwards. the large filament(brake/ blinker) is staying on when the lights are on rather than the small filament(running lights).


Well you will have to check for a short or melted plug for the lights otherwise you might have to cut the 3 wires to the lights and replace the sockets to the bulbs because the corrosion or melted plug internally is bad

Mar 29, 2014 | Cars & Trucks

1 Answer

2001 DODGE DURANGO RT REAR TAIL LIGHT OUT AND FRONT LEFT HEADLIGHT GOES OUT BUT TAP HEADLIGHT AND IT COMES BACK ON


Check the harness connection for trailer hitch lights near back bumper in chassis rail. launching a boat gets this connector corroded.

May 17, 2017 | Dodge Durango Cars & Trucks

2 Answers

My brake lights and rear blinkers are not working. I have replaced the bulbs in both brake lights. What next?


most blinkers uses relays, and when they flashes fast one light is out, but you replaced your burnt bulb might be a bad relay.

Sep 17, 2012 | 2007 Hummer H2 SUT

2 Answers

2007 tail light fuse location honda crv


I had this problem with my 2007 Honda CRV -- all the lights worked EXCEPT the tail/running lights and the license plate light. The other tail lights worked -- brake, reverse, indicators, and hazards. Front headlights also worked, but when the headlights went on the back tail lights did not (not to safe for driving at night!!)
The fuse was #15 in the interior fuse box (under the dash driver side) with the label "small exterior lights" ( also check fuse #19 labeled "small lights main"). The cause of my problem, I believe, is a bad or lose wire in my license plate light.

Jan 16, 2012 | Honda Civic Cars & Trucks

1 Answer

My brake lights and rear blinkers are not working, I checked light bulbs (tail lights work) and fuses. what next


typically with gm the brake light and turn signals work on the same filament, so just because the tail lights come on does not mean that the bulb is not burned out. try simply replacing the bulbs.

Feb 21, 2011 | 2001 Chevrolet Cavalier

1 Answer

Brake Lights and Hazard still dont work


TEST FRONT RIGHT BLINKER CIRCUIT AND REPLACE THE BULB,,WITH PROPER BULB...A DOUBLE CIRCUIT BULB IN A SINGLE SOCKET WILL DO THAT ALSO A SINGLE SOCKET BULB IN A DOUBLE SOCKET HOLDER....CHECK LEFT SIDE BULB FOR ACURANCY

Aug 29, 2009 | 1993 Chevrolet Astro

2 Answers

2001 chevolet cavilier brake lights & blinkers burning up


sounds like you put a 21 watt bulb in place of a 6 watt bulb ,or you have put single pole bulb in place of a double filament,double pole bulb

Feb 02, 2009 | 2001 Chevrolet Cavalier

1 Answer

2001 ford explorer sport trac


Just found the answer on another site. Sure enough went out removed the 3 philips head screws in the steering column opened it up and walla a wire connection had pulled itself free. When my son uses my truck he always uses the tilt steering, when I get in I have to readjust it. because of this the wire connection pulled itself out. I simply pushed it back in an blinker and brake light are now working. My husband is now trying to figure a way to secure the wire connection so it doesn't pull itself out again. Hope this helps others, either by saving the cost of a dealership or machanic or from getting rear ended.

Aug 02, 2008 | 2001 Ford Explorer Sport Trac

Not finding what you are looking for?
2001 Honda CR-V Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...