Question about 2005 Chevrolet Malibu

Open Question

WHERE IS THE PURGE SOLENOID AT ON A 2005 MALIBU 3.5L v6 located at

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 109 Answers

SOURCE: thermostat location 2005 malibu

it should be located on the laft side of the motor just follow the bottom hose on your radiator cause that runs directly into the thermostat..

Posted on Dec 04, 2008

  • 1596 Answers

SOURCE: location of the evaporative cannister solenoid? 2003 saturn vue

Depends if the engine is 3.0 or a 2.2?
3.0 purge is on the top, back side of the intake. Black, cylinder. Looks the same on a 2.2, but is located next to the air filter.

Posted on Jan 24, 2009

SOURCE: purge solenoid location

which vehicle are you actually looking for the purge solenoid on? you have 2 vehicles listed in your question. i'll answer both, lol

the locations are described as if you are looking at the engine from the front of the car with hood open.

on the blazer:

it is located on the left side of the intake manifold just under and behind the throttlebody. it is a canister looking device.

on the silverado:

it is located on the intake manifold on the left side in about the same spot as the blazer. providing the silverado has the 5.3 or 5.7 liter engine. if it also has the 4.3 then obviously it will be the same.

hope this helps!

Posted on Feb 17, 2009

longbow243
  • 103 Answers

SOURCE: 2007 SILVERADO V6 EVAP PURGE SOLENOID

The evap purge solenoid is located on the intake manifold. The evap vent valve is located on the side of the fuel tank. If you have a P0449 or P0452 (I think) DTC, it will be the one on the tank that you need to replace.

Posted on Sep 01, 2009

johnjohn2
  • 5763 Answers

SOURCE: I have a 2005 chevy malibu v6 3.5 motor and was

this car doesnt have a power steering pump, this car uses an electric motor to provied power steering, this motor is located under the dash connected to steering column shaft,when replacing the motor the module must also be replaced, here is a diagram to help you locate the motor,94445b2.gif

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the canister purge valve located on a 2005 Buick LaCrosse CXS with a 3.6 L


Remove the plastic cover off top of engine . purge valve solenoid under it.

Evaporative Emission (EVAP) Canister Purge Solenoid Valve
Top rear of the engine, on the intake manifold, near the fuel injectors. If you don't know what it looks like google part to see a picture .

Dec 31, 2016 | 2005 Buick LaCrosse

1 Answer

Where is the purge valve solenoid on a 2005 v-6 Mustang located?


Near the carbon canister at rear of car near the gas tank..

Feb 28, 2016 | 2005 Ford Mustang V6

1 Answer

Where is the evap vent solenoid fuse located on 2005 nissan altima


It doesn't have a "fuse" specific to the purge valve solenoid. What he is telling you is that you need to have this circuit troubleshot. Either the PCM the wiring going to the purge valve solenoid, or the purge valve solenoid itself is malfunctioning.

This requires a scanner, a digital volt ohm meter and some knowledge of when the purge valve actuates and under what conditions.

The car must be running and operating at cruising speed before the PCM sends a command to the purge valve to operate. Some scanners have the ability to send a request to the PCM to actuate the purge valve, but that scanner is usually a dealer's or equivalent.

May 08, 2015 | 2005 Nissan Altima

2 Answers

Where is the purge solenoid on an 01 Dodge Stratus 3.0L V6?


On top of the fuel tank, it plugs into the tank in a groment and has a vacume line on it and a three wire connector with a weather tight plug.

Dec 26, 2010 | 2001 Dodge Stratus

2 Answers

Check engine light code p1676 Chevy lumina Ltz


Trouble Code: P1676 (3.8L V6 VIN K Auto)
Evaporative Emission (EVAP) Purge Solenoid

Number of Trips to Set Code: 1
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
Conditions for Setting the DTC.
  • The ignition is on.
  • An improper voltage level has been detected on the output circuit which controls the EVAP purge solenoid.
  • The above conditions are present for at least 30 seconds.

Possible Causes:
  • Poor connection at the PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection.
  • Damaged harness.
  • Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM, turn the ignition on and observe a voltmeter connected between the EVAP purge solenoid control circuit and ground at the PCM harness connector while moving connectors and wiring harnesses related to the EVAP purge solenoid. A change in voltage will indicate the location of the malfunction.

1998 Chevrolet Lumina - Powertrain - Engine Controls - 3.8L - DTC P1676 Evaporative Emission (EVAP) Purge Solenoid Control Circuit

Aug 13, 2010 | 1998 Chevrolet Lumina

1 Answer

Were is the evap located on 2001 Chevy s-10 blazer with v6


The EVAP service port is located in the EVAP purge pipe between the EVAP purge solenoid and the EVAP canister. The service port is identified by a green colored cap.

47e8f38.jpg

Fig. Showing location of (1) Evaporative Emissions (EVAP) Canister Purge Solenoid and (2) Exhaust Gas Recirculation (EGR) Valve


4d7b3e9.jpg

Fig. EVAP Purge valve solenoid (3) mounting bolt (2) and insulator (1) on 2000-2005 4.8L, 5.3L, 6.0L Engines

Hope this help (remember rated the post).

Mar 26, 2010 | 2001 Chevrolet Blazer

1 Answer

2007 SILVERADO V6 EVAP PURGE SOLENOID


The evap purge solenoid is located on the intake manifold. The evap vent valve is located on the side of the fuel tank. If you have a P0449 or P0452 (I think) DTC, it will be the one on the tank that you need to replace.

Sep 01, 2009 | 1999 Chevrolet Silverado 1500

3 Answers

Where is the purge solenoid location on a 1996 Chevrolet silverado 1500 ???? trucks runs bad and I was told it was that or some other vacuum leak also I have code p0300 and p1441 if anyone can help...


A P0300 DTC is a misfire code. The P1441 is a no flow during purge code which has to do with the purge solenoid. With the misfire code present I would say you have a vacuum leak on one of the hoses. The purge solenoid is located in the passenger side, rear of the intake manifold.

May 09, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Thermostat location 2005 malibu


it should be located on the laft side of the motor just follow the bottom hose on your radiator cause that runs directly into the thermostat..

Dec 04, 2008 | 2005 Chevrolet Malibu

Not finding what you are looking for?
2005 Chevrolet Malibu Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...